• Journal of Advanced Marine Engineering and Technology
• /
• 제23권3호
• /
• pp.284-291
• /
• 1999

Recently the ductile cast iron is being used successfully to the parts for processing machinery vessels and gear etc. This study is mainly concerned with the heat treatment for the specimens of crank shaft which are made of ductile cast iron. The results obtained are summarized as follows. Comparing the mechanical properties of the specimens for the normalized ductile cast irons the specimen heat treated at $550^{\circ}C$ was the best for crank shaft of air-compressor. After austenizing at $910^{\circ}C$ it was observed that the higher the reheating temperature is the less tensile strength and the hardness became which was supposedly attributed to the fact that the amount of pearlite. Austenite matrix was reduced by reheating after normalizing and that as the reheating tem-perature went up the pearlite generated was less and the distance between the pearlites were widened at last made pearlite globular. In the comparsison of crank shaft for air compressor made of ductile cast iron with that made by forged steel the crank shaft made of ductile cast iron was superior in economical terms. And ductile cast iron could be practically enough if only the elonga-tion which was inferior mechanical property to forged steel could be reinforced by increasing the diameter of crank pin when designing the crank shaft.

• Archives of Plastic Surgery
• /
• 제34권1호
• /
• pp.18-23
• /
• 2007

Purpose: Anthropometry can be divided into two methods, direct anthropometry and indirect anthropometry. The most ideal and accurate method is a direct anthropometry. However, it is difficult to measure in the case of children because of poor cooperation, and it lacks re-productivity. Cast model has advantages of three dimensional featuring, inexpensive and easy fabrication. This study is conducted to find out an accuracy of indirect anthropometry on cast model by comparing it with direct anthropometry. Methods: Total 48 cleft lip nasal deformity patients (unilateral, 40; bilateral, 8) were included in this study. Cast models were made before surgery under general anesthesia with alginate impression material and model plaster. Eleven linear measurements among 7 landmarks were taken as direct anthropometry before surgery with Castroviejo spreading caliper. At the same time, indirect anthropometry on cast model was done at the same linear distances as well. Results: Of the total 11 linear measurements, both ala lengths, both columella lengths, nose width, projective distance between facial insertion points of the ala, projective distance between the alar base points, right nostril floor width, and columella width were statistically correlated between indirect anthropometry on cast model and direct anthropometry. However, the nasal tip protrusion and the left nostril floor width were not statistically correlated. Conclusion: Accuracy of indirect anthropometry on cast model can be influenced by cast model fabrication techniques and correct identification of landmarks. Nasal tip protrusion could be reduced by compression of the nasal tip in the process of cast model fabrication and nostril floor width can be varied by muscle relaxation of anesthetics and incorrect identification of subalare in cleft lip nasal deformity. If sufficient care is taken to make cast model and to define landmarks exactly, indirect anthropometry on cast model can be a reliable method as direct anthropometry.

• 비파괴검사학회지
• /
• 제32권2호
• /
• pp.155-161
• /
• 2012

초음파 속도를 이용하여 다양한 종류의 주철에 대해 미세구조와 품질 특성을 평가하였다. 상용으로 사용되는 3종의 회주철 및 3종의 구상흑연주철을 준비하였으며, 열처리 미세구조의 영향을 평가하기 위해 구상흑연주철을 어닐링 열처리를 다르게 하여 시편을 준비하였다. 초음파 전파 속도 측정, 미세구조(펄라이트 분율, 흑연의 길이 및 구상화율) 정량화, 경도 측정을 행하여 이들 파라미터 사이의 경험적 상관관계를 확인하였다. 구상흑연주철의 초음파 전파 속도가 회주철에서의 속도보다 크게 나타났다. 구상흑연주철에서 펄라이트 미세조직의 분율이 감소할수록 경도 및 초음파 속도는 감소하였다. 초음파 속도를 주철 소재의 품질관리를 위한 비파괴평가 파라미터로서 사용할 수 있는 가능성을 보여주었다.

• 한국유기농업학회지
• /
• 제11권1호
• /
• pp.55-66
• /
• 2003

본 연구에서는 음식물쓰레기와 축분의 vermicomposting 처리로 얻어지는 지렁이 분립을 이용하여 채소의 육묘상토 자재로서의 이용가능성을 조사하기 위해, 시판상토 100％, 지렁이분립 100％, 지렁이분립 50％ ＋ vermiculite 50％, 지렁이분립 50％ + Perlite 50％ 및 지렁이분립 40％ ＋ vermiculite 30％ ＋ perlite 30％의 각각 다른 지렁이분립 혼합비율이 토마토(Lycopersicum esculentum Mill.) 유묘의 생육에 미치는 영향을 조사하였다. 토마토 생육 2주째까지는 시판상토구가 전 처리구에서 초장, 엽수, 경경, 엽중, 경중, 지상부중, 근중 및 생물수량이 가장 높았지만, 이후부터는 지렁이 분립 100％구가 다른 처리구보다 유의하게 높았으며 (p<0.05), 시판상토구에 비해서도 양호한 생육을 나타내었다. 지렁이 분립과 Vermiculite를 혼합한 구는 시판상토구와 유사한 생육을 나타내었다. 한편 생물수량의 상대생장율(BYRGR), 지상부 무게의 상대생장율(RGR) 및 지하부무게의 상대생장율(RWGR)은 생육 4주 째까지 지렁이 분립 100％ 구가 다른 처리구 보다 유의하게 높았다(P<0.05).

• Restorative Dentistry and Endodontics
• /
• 제19권1호
• /
• pp.64-72
• /
• 1994

Zinc Phosphate Cement hand been used for about more than 100 years in luting of cast gold inlay. But many scientists had been trying to develop the new form of luting agent because the ZPC hand shown the lack of adhesiveness on the tooth structure and the toxicity to the pulp tissue. Recently many researches about the surface treatment of the cast body are being done to increase the adhesion of cement to it. The conventional Class I gold inlays were fabricated in the 20 permanent molars. After the internal surface of the cast body was sandblasted with $Al_2O_3$ particles and was tin-plated, the inlays were cemented with adhesive cement [G I cement and resin cement(Super-Bond & $Panavia_{EX}$)] and the evaluation on the adhesion pattern, adhesive strength and the fracture pattern of the adhesive cast gold inlay was compared to that of the cast gold inlay cemented conventionally with ZPC. The results were as follows : 1. The surface roughness of the cast body was increased significantly after sandblasting with the $Al_2O_3$ particles and the tin oxide layer, which was consisted of round particles, came into being. 2. The bond strength was in the order of Super-Bond, ZPC, Fuji I, $Panavia_{EX}$ group. The group cemented with Super-Bond showed statistically greater strength than the other groups(p<0.05). 3. The group cemented with ZPC was fallen apart by principal adhesion failure and that with Fuji I was by complete adhesion failure. But the group with Super-Bond showed pricncipal cohesive failure pattern and in the group with $Panavia_{EX}$, complete cohesive fracture pattern was shown and small protion of tooth structure was fractured out with cast body and the fractured surface showed the figure just as the enamel prism. 4. Various gaps were shown at the pulpal side regardless of little gap at the side walls of the cavity in all groups. Only the Super-Bond was attached to the tooth structure and the other cements were detached from both the tooth and the cast body.

• 대한의생명과학회지
• /
• 제15권1호
• /
• pp.47-53
• /
• 2009

Urinary bladder cancer is diagnosed through urine cytology and cytoscopy with biopsy. An atypical urothelial cast is often found by voided urine cytology in a papillary urothelial cell carcinoma. The objective of this study is to demonstrate the significance of the evaluation of urinary nuclear matrix protein (NMP22) level and Sure Path Liquid-based cytology (SP-LBC) as compared to the examination of atypical urothelial cast in voided urine sediment for monitoring bladder cancer. From October 2007 to January 2008, we observed 3240 patients who visited the emergency laboratory of urology of Soonchunhyang University, Cheonan Hospital. Both NMP22 measurement and SP-LBC were performed in 31 patients who were positive in an atypical urothelial cast test. In particular, 26 men and 5 women were found to be atypical urothelial cast-positive persons. The average age for both men and women is 61.8. NMP22 test is positive in 23 of 31 cases (74.2%) from patients with atypical urothelial cast, while the test is negative in 8 of 31 cases (25.8%). The percentages of negativity, atypicality, suspicious malignancy, and malignancy in SP-LBC are 25.8% (8/31), 58.1% (18/31), 9.7% (3/31), and 6.5% (2/31), respectively. The relation of NMP22 positivity with the malignant degree in LBC is significant (P<0.01). Two malignant patients resulting from SP-LBC show the same results in histological examination. Overall, the study suggests the usefulness of NMP22 measurement and LBC as well as the examination of atypical urothelial cast for the diagnosis of early bladder cancer.

• Smart Structures and Systems
• /
• 제7권4호
• /
• pp.241-262
• /
• 2011

Cast iron pipe has been used as a water distribution technology in North America since the early nineteenth century. The first cast iron pipes were made of grey cast iron which was succeeded by ductile iron as a pipe material in the 1940s. These different iron alloys have significantly different microstructures which give rise to distinct mechanical properties. Insight into the non-destructive structural condition assessment of aging pipes can be advantageous in developing mitigation strategies for pipe failures. This paper examines the relationship between the small-strain and large-strain properties of exhumed cast iron water pipes. Nondestructive and destructive testing programs were performed on eight pipes varying in age from 40 to 130 years. The experimental program included microstructure evaluation and ultrasonic, tensile, and flexural testing. New applications of frequency domain analysis techniques including Fourier and wavelet transforms of ultrasonic pulse velocity measurements are presented. A low correlation between wave propagation and large-strain measurements was observed. However, the wave velocities were consistently different between ductile and grey cast iron pipes (14% to 18% difference); the ductile iron pipes showed the smaller variation in wave velocities. Thus, the variation of elastic properties for ductile iron was not enough to define a linear correlation because all the measurements were practically concentrated in single cluster of points. The cross-sectional areas of the specimens tested varied as a result of minor manufacturing defects and levels of corrosion. These variations affect the large strain testing results; but, surface defects have limited effect on wave velocities and may also contribute to the low correlations observed. Lamb waves are typically not considered in the evaluation of ultrasonic pulse velocity. However, Lamb waves were found to contribute significantly to the frequency content of the ultrasonic signals possibly resulting in the poor correlations observed. Therefore, correlations between wave velocities and large strain properties obtained using specimens manufactured in the laboratory must be used with caution in the condition assessment of aged water pipes especially for grey cast iron pipes.

• 소성∙가공
• /
• 제8권3호
• /
• pp.295-295
• /
• 1999

In the present study, the corrosion behavior of AZ91D as-cast alloy was investigated form the viewpoint of the distribution aspect of precipitate ($Mg_{17}Al_{12}$) and the variation of Al concentration in the Mg-rich matrix. The dendrite arm spacing (DAS) of an as-cast specimen was measured as a function of degree which describes the distribution aspect of the precipitate, and the salt spray test was conducted for various grain-sired specimens fur 20 days. The dendrite arm spacing increased as the grain size increased to about 150㎛, but a constant value is indicated when the grain size exceeds that range. Although the relationship between the corrosion rate and grain size is of a nonlinear type, the linear trend between the corrosion rate and the dendrite arm spacing is maintained for the overall range of dendrite arm spacing. Since the precipitate in the as-cast alloy is discontinuously distributed, this linear relationship means that the variation of Al-solute concentration in the Mg-rich matrix has a more potent effect than the protective action of the precipitate on the corrosion behavior of an as-cast alloy.

• 대한치과보철학회지
• /
• 제31권4호
• /
• pp.461-467
• /
• 1993

The purpose of this study was to evaluate the effects of method for construction of cast post and type of dental cement on the retention of cast post. The wax patterns or Duralay resin patterns were used for construction of cast post. The dental cements used in this study were zinc phosphate cement(Fleck's zinc cement, Mizzy INc., U.S.A.), glass ionomer cement(Fuji I, G-C Co., Japan), and resin cement(Panavia-EX, Kuraray Co., Japan) and the retention of cast post was measured with Instron Universal Test Machine(Instron Engineering Co., U.S.A.). The obtained results were as follows : 1. The tensile bond strength of cast posts made by Duralay resin patterns revealed 39.13(kg) with Panavia-EX, 46.40(kg) with phosphate cement, and 37.78(kg) with glass ionomer cement. 2. The tensile bond strength of cast posts made by wax patterns revealed 39.25(kg) with Panavia, EX, 44.12(kg) with phosphate cement, and 40.23(kg) with glass ionomer cement. 3. The tensile bond strength of cast posts made by Duralay resin patterns or wax patterns were not affected by the type of dental cements(P>0.05).

• 한국지능정보시스템학회:학술대회논문집
• /
• 한국지능정보시스템학회 2006년도 춘계학술대회
• /
• pp.327-335
• /
• 2006

Case Based Reasoning (CBR) has come to be considered as an appropriate technique for diagnosis, prognosis and prescription in medicine. However, canventional CBR has a limitation in that it cannot incorporate asymmetric misclassification cast. It assumes that the cast of type1 error and type2 error are the same, so it cannot be modified according ta the error cast of each type. This problem provides major disincentive to apply conventional CBR ta many real world cases that have different casts associated with different types of error. Medical diagnosis is an important example. In this paper we suggest the new knowledge extraction technique called Cast-Sensitive Case Based Reasoning (CSCBR) that can incorporate unequal misclassification cast. The main idea involves a dynamic adaptation of the optimal classification boundary paint and the number of neighbors that minimize the tatol misclassification cast according ta the error casts. Our technique uses a genetic algorithm (GA) for finding these two feature vectors of CSCBR. We apply this new method ta diabetes datasets and compare the results with those of the cast-sensitive methods, C5.0 and CART. The results of this paper shaw that the proposed technique outperforms other methods and overcomes the limitation of conventional CBR.