• Journal of Korea Foundry Society
• /
• v.21 no.3
• /
• pp.198-203
• /
• 2001

In determining properties of ductile cast iron, it is well known that nodularity plays a significant role. Therefore, the national and/or international standards for ductile cast iron such as KS, ISO, ASTM and JIS have specified some methods for evaluating it. However, most of standards have not recommended the methods using image analyzer which is known as an objective analyzing tool for evaluating microstructure. In this study, a reliable method for evaluating nodularity by image analyzing method was proposed, and the result was compared with that from the common counting method proposed in KS D 4302-1999. It was found that there was a reasonable relationship in nodularities measured by these two methods.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2000.04b
• /
• pp.77-84
• /
• 2000

In this paper, the stress analysis of the cast iron insert of spent nuclear fuel disposal canister in a deep repository at 500m underground is done for the underground pressure variation. Since the nuclear fuel disposal usually emits much heat and radiation, its careful treatment is required. And so a long term safe repository at a deep bedrock is used. Under this situation, the canister experiences some mechanical external loads such as hydrostatic pressue of underground water, swelling pressure of bentonite, sudden rock movement etc.. Hence, the canister should be designed to withstand these loads. The cast iron insert of the canister mainly supports these loads. Therefore, the stress analysis of the cast iron insert is done to determine the design variables such as the diameter versus length of canister and the number and array type of inner baskets in this paper, The linear static structural analysis is done using the finite element analysis method. And the finite element analysis code, NISA, is used for the computation.

• Biomedical Science Letters
• /
• v.13 no.2
• /
• pp.91-97
• /
• 2007

Obesity is defined as increased mass of adipose tissue, conferring a higher risk of cardiovascular and metabolic disorders such as diabetes, hyperlipidemia, and coronary heart disease. To get a better understanding of the role of a male sex hormone testosterone on obesity, we thus measured the effects of testosterone on white adipose tissue (WAT) mass, adipocyte histology and hepatic lipid accumulation in male castrated (CAST) C57BL/6J mice. Compared to male CAST control mice, testosterone-treated mice had the decreased WAT mass and the increased the number of adipocytes. Especially, histological data showed that the adipocyte size was reduced in a dose-dependent manner and was most effective at dose 150 $\mu$g per mouse for testosterone. In addition, the administration of testosterone resulted in the inhibition of hepatic lipid accumulation compared with control mice. Our results suggest that testosterone regulates adipocytes development and hepatic lipid metabolism, resulting in the prevention of obesity in male CAST mice.

• Tribology and Lubricants
• /
• v.8 no.1
• /
• pp.63-69
• /
• 1992

In order to gain better understanding of wear behaviors of TiN-coated boron cast iron, tests and analyses were conducted with block-on disc type tribometer. TiN layer of thickness $2 \mu m$ and $4 \mu m$, coated by cathodic arc evaporation process, were experimentally investigated with the variation of applied load and sliding speed under dry sliding condition. Wear characteristics were expressed in terms of the three-dimentional wear map as well as the wear rate vs sliding speed and load. Comparisons of wear and friction characteristics between coated cast irons and uncoated cast irns were also made. Wear mechanism of TiN layer was explained in view of surface interaction between the mating surfaces. The thicker coating exhibited higher hardness and adhesion strength. the significance of stresses at the surface and in the subsurface was briefly discussed in relation to the wear behavior.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.6
• /
• pp.42-47
• /
• 2001

In this study, fatigue limit of ductile cast iron is evaluated based on phenomena of the microscopic observation, such as matrix structure, spheroidal ratio, size of graphite and distribution. Three different ferrite-pearlite matrix structure, GCD 45-), GCD 50, GCD 60 series, all of which contain more than 70% spheroidal ratio of graphite, were used to obtain the correlation between maximum size of graphite and fatigue strength. It was concluded as fellows. (1) In Ductile cast iron of ferrite-pearlite matrix, the fatigue limit of GCD 60 series with 73% pearlite structure was the highest. (2) From observation of the starting point of crack of all specimens, it is noted that the crack initiates, in graphite, goes through ferrite and propagates into pearlite. (3) A good quality of Ductile cast iron used in this experiment can be checked from uniformly distributed graphite. The negligible interaction effect between graphites was verified by microscopic observation and fracture mechanics investigation in surface and interior of the specimen.

• Journal of Korea Foundry Society
• /
• v.3 no.2
• /
• pp.92-99
• /
• 1983

This study has been carried out to investigate into the difference of rolling life and rolling wear characteristics for various gray cast iron under unlubricated dry rolling condition by amsler type wear test with 9.09% sliding.The results obtained from this study are summerized as follows: 1) It has been found that the amount of rolling wear id decreased when tensile strength and hardness are low, and then the rolling life up to generation of abnormal wear is conspicuously increased. 2) At the given condition the amount of rolling wear has been found to decrease as carbon equivalent of gray cast iron increases and resistance of crack propagation is an important factor on improvement of wear characteristics. 3) The amount of rolling wear is increased with increasing rolling revolution and wear of gray cast iron under dry rolling condition is characterized by three modes; initial wear, stationary wear and abnormal wear. 4) It has been found that the amount of rolling wear is increased with increasing maximum compressive stress and extremely increased when maximum compressive stress is over 59.1kg.f/mm.

• Journal of Powder Materials
• /
• v.18 no.1
• /
• pp.24-28
• /
• 2011

Effect of Cu content on microstructural and magnetic properties of a $(Nd_{26.06},Dy_{6.51})Fe_{bal.}$ $Cu_xB_{0.97}$(wt.%), (x = 0.2, 0.3, 0.4, 0.5) strip-cast was studied. The average inter-lamellar spacing in the free surface and wheel side of the strip cast increased as the Cu content increases. The grain uniformity, the grain alignment, and (00L) texture of the strip cast increased with Cu contents up to 0.4 wt.%. These microstructural changes were attributed to the decrease of the effective cooling rate of the melted alloy caused by the decrease of the melting temperature of resulting from Cu addition. Coercivity and remanence were increased because of the grain alignment and (00L) texture improvement with Cu contents up to 0.4 wt.%.

• Journal of Korea Foundry Society
• /
• v.21 no.6
• /
• pp.350-358
• /
• 2001

The machinability of cast iron is closely related to its microstructural property. In this study, the effect of graphite mophology and matrix microstructure on machinability in several commercial cast irons(GC 25, GCD 45, GCD 50, GCD 70, GCD HSMo, GCMP) was investigated. To estimate the machinability, turning test was carried out under conditions of spindle speed 80m/min, depth of cut 0.25mm, feed 0.16mm/rev and cutting distance 1 km. Thrust force in turning test decreases in the order of GCMP, GCD 70, GCD 50, GC 25, GCD 45 and GCD HSMo. i.e. machinability increases in this order. The superior machinability of GC 25 is caused by flake type graphite which acts as chip braker and provides lubrication during machining. Consequently, soft ferritic cast irons exhibit superior machinability compared with pearlitic cast irons.

• Resources Recycling
• /
• v.9 no.1
• /
• pp.15-20
• /
• 2000

The effect of different kinds of steel scraps, the raw material in the manufacturing of nodular cast iron, on the microstructures and mechanical properties has been investigated Different grades were produced by changing the steel scraps. When nodular graphite cast iron was produced by using Zn rich steel scrap, such as galvanized steel sheet and auto body sheet, mechanical properties were deteriorated due to the decomposition of graphite, so close control must be maintained over this element. Tensile strength and hardness of nodular graphite cast iron which were manufactured by using Sb rich steel scrap were increased while elongation was decreased due to the increased amounts of pearlite within matrix. Mn and Cr contents in the structural steel sheet scrap or malleable iron scrap increased tensile strength and hardness of nodular graphite cast iron by facilitating the formation of pearlite.

• The Journal of Korean Academy of Prosthodontics
• /
• v.32 no.3
• /
• pp.359-367
• /
• 1994

The number and the distribution of fixed restorations including crowns, fixed bridges, Maryland bridges, periodontal splints and cast cores were statistically investigated with two thousand seven hundred and thirty cases of crowns and bridges placed at the Department of Prosthodontics of Seoul National University Hospital, from January 4th to December 31st, 1988. The results were as follow : 1. Among the fixed restorarions, single crowns were 46.9% , fixed bridges were 41.9%, Maryland bridges were 5.0%, periodontal splints were 0.6% and cast cores were 5.6%. 2. Three thousand nine hundred and ninty two teeth were restored with the fixed restorations, among them cast gold restorations were 47.2% and metal-ceramic restorations were 52.8%. 3. Cast gold restorations of the maxillary posteriors occupied 98.5% of the maxillary cast gold restorations, and 99.7% of the mandibular cast gold restorations and metal-ceramic restoration of maxillary anteriors occupied 68.4% of the maxillary metal-ceramic restorations, and 38.7% of the mandibular metal- ceramic restorations. 4. It is recommended that the curriculum of the dental school for undergraduated students and graduated students should be changed to accomodate the relative importance of the restorations.