• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.3
• /
• pp.213-218
• /
• 2014

CFD flow simulation of vehicles with open sunroof and passenger window help the automotive OEM(original equipment manufacturer) to identify the low frequency noise levels in the cabin. The lock-in and lock-off phenomena observed in the experimental studies of sunroof buffeting is well predicted by CFD speed sweep calculations over the operating speed range of the vehicle. The trend of the shear layer oscillation frequency with vehicle speed is also well predicted. The peak SPL from the CFD calculation has a good compromise with the experimental value after incorporating the real world effects into the CFD model by means of artificial compressibility and damping correction. The entire process right from modeling to flow analysis as well as acoustic analysis has been performed within the single environment i.e., STAR-CCM+.

• Journal of Veterinary Clinics
• /
• v.29 no.4
• /
• pp.348-351
• /
• 2012

A vaginal speculum examination of a 17-month-old Holstein heifer with a history of repeated artificial insemination (AI) failures via the cranial vagina revealed the presence of an intact hymen (imperforate hymen) beyond the external urethral orifice, which resembled the vaginal wall. An ultrasonographic examination detected hypoechoic fluid within the vaginal cavity between the intact hymen and the cervix, indicating the presence of hydrocolpos. After sedation and epidural anesthesia, the intact hymen was incised using a scalpel and scissors and removed, while the incised portions were sutured using a simple interrupted method. The heifer became pregnant after three consecutive estruses with the intervals of approximately 20 days and concomitant AIs. The heifer gave birth to a healthy male calf with no complications after a 291-day gestation period. This case reports the presence of an imperforate hymen with hydrocolpos in a Holstein heifer, followed by successful insemination, conception and delivery after removal of the imperforate hymen.

• Restorative Dentistry and Endodontics
• /
• v.22 no.1
• /
• pp.464-469
• /
• 1997

The radiopacity of glass ionomer cements is quite variable. The use of a poorly radiopaque material as a base under other restorative materials can mislead the dentist to a diagnosis of recurrent decay. This study investigates the radiopacity of these materials and proposes a minimal radiopacity under which a material should not be used as a base or liner. It is important to determine the radiopacity of glass ionomer dental materials so that the clinician can appreciate the type of restorative materials used when radiographically evaluation the possibility of recurrent dental caries. In this study, radiopacity of Vitrement and Chemfil was compared with that of Cavalite, Miracle mix and polycarboxylate cement. Tooth model of artificial cavity preparation for diagnosis of recurrent caries was omitted. Radiopacity of each material was measured using relatives between thickness and radiopacity of Aluminium step wedge. The results were as follows : 1. Radiopacity of Vitrement was some higher than enamel. 2. Chemfil, restorative glass ionomer, was less radiopaque than enamel. 3. In order of higher radiopacity than enamel, Miracle mix was highest and was followed by polycarboxylate cement, Cavalite and Vitremer. 4. Vitremer, the Glass Ionomer Cement, is useful to detection of recurrent caries, because it is slightly higher radiopaque than enamel. So, it is suitable for restorative material and luting cement.

• Journal of Korean Biological Nursing Science
• /
• v.22 no.3
• /
• pp.176-183
• /
• 2020

Purpose: : The purpose of this study was to evaluate the intrauterine insemination (IUI) success rate and to define the variables for predicting success. Methods: The secondary data analysis was used with data collected from infertile females who underwent IUI in Fertility and IVF (In Vitro Fertilization) clinics, who benefited from the 'National Medical-aid Program for ART (assisted reproductive technology) in 2016', in which the data of 34,920 IUI cases were retrospectively reviewed. The primary outcome measure was the clinical pregnancy rate in elderly and young infertile females. Data were analyzed by descriptive statistics, χ2 test and logistic regression. Results: The pregnancy rate was 12.1% (2,095 cases) in elderly infertile females and 15.6% in young infertile females (2,758 cases) (χ2 = 87.90, p< .001). Using the logistic regression analysis, clinical pregnancy was positively associated with the ovulatory factor (OR= 1.48, p< .001) and male factor (OR= 1.19, p< .05) in elderly infertile females. It was positively associated with the ovulatory factor (OR= 1.30, p= .001) and the peritoneal cavity factor (OR= 0.58, p< .05) in young infertile females. Conclusion: Our results indicate that the pregnancy rate in young infertile females was higher than that in old infertile females, and the IUI is the effective option in pregnancies in all ages with infertility due to the ovulatory factor. Additionally, further studies are necessary to fully describe pregnancy experiences for all the infertile females.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.2
• /
• pp.169-174
• /
• 2011

Acoustic emission (AE) signals were detected and analyzed in real time during the polymerization shrinkage of composite resin restoration in an artificial dental ring with a class I cavity. Most AE hit events were observed in the initial curing period of the 1st region with high contraction rate. The range of the $2^{nd}$ region for the stainless steel specimen was shorter than that for the PMMA specimen but longer than that for the human dentin specimen. AE hit events showed a blast-type signal having an amplitude in the range of 25.45 dB and a frequency band of 100.200 kHz or 240.300 kHz. These values of amplitude and frequency indicated the fracture of resin or of the adhesive layer.

• Economic and Environmental Geology
• /
• v.57 no.1
• /
• pp.17-23
• /
• 2024

Ground penetrating radar (GPR) survey is a geophysical method that utilizes electromagnetic waves reflecting from a boundary where the electromagnetic property changes. As the frequency of the antenna is about 25 MHz ~ 1 GHz, it is effective to acquire high resolution images of underground pipe, artificial structure, underground cavity, and underground structure. In this study, we analyzed the change of signals reflected from the same underground objects according to the arrangement of transceiver antennas used in ground penetrating radar survey. The antenna used in the experiment was 200 MHz, and the survey was performed in the vertical direction across the sewer and the parallel direction along the sewer to the sewer buried under the road, respectively. A total of five antenna array methods were applied to the survey. The most used arrangement is when the transmitting and receiving antennas are all perpendicular to the survey line (PR-BD). The PR-BD arrangement is effective when the object underground is a horizontal reflector with an angle of less than 30°, such as the sewer under investigation. In this case study, it was confirmed that the transmitter and receiver antennas perpendicular to the survey line (PR-BD) are the most effective way to show the underground structure. In addition, in the case where the transmitting and receiving antennas are orthogonal to each other (XPOL), no specific reflected wave was observed in both experiments measured across or parallel to the sewer. Therefore, in the case of detecting undiscovered objects in the underground, the PR-BD array method in which the transmitting and receiving antennas are aligned in the direction perpendicular to the survey line taken as a reference and the XPOL method in which the transmitting and receiving antennas are orthogonal to each other are all used, it can be effective to apply both of the above arrangements after setting the direction to 45° and 135°.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.27 no.2
• /
• pp.361-369
• /
• 2000

Enterococcus is a normal inhabitant of the human oral cavity, the vagina, and the gastrointestinal tract. Four isolates of Enterococcus in this study were identified as E. durans. These bacteria were characterized and the interaction of these bacteria with the important oral bacteria as like S. mutans and S. oralis was studied as follows. 1. The carbohydrate fermentation test and biochemical test showed similar results in 4 isolates. 2. The susceptibility test against erythromycin, penicillin, tobramycin, ampicillin, teicoplanin, ciprofloxacin, vancomycin, gentamicin, kanamycin, and streptomycin showed to be susceptible in all four isolates. 3. The optical density of absorbance at 550 nm was 1.405 in the culture of S. mutans in disposable cuvette, whereas being 0.855, 0.867, 0.797, and 1.083 in the combined culture of S. mutans and each E. durans. 4. The mean weight of produced artificial plaque on the wires in the beaker was $1566{\pm}103mg$ in culture of S. mutans only, whereas being reduced to $44{\pm}5mg,\;41{\pm}12mg,\;34{\pm}7mg,\;and\;38{\pm}12mg$ in the combined culture of S. mutans and each E. durans. The viable cells were $2.0\times10^9$ per ml in the culture of S. mutans wheras being $2.0\times10^7\;to\;6.0\times10^7$ per ml in the combined culture S. mutans and E. durans. 5. The viable cells were $2.1\times10^8$ per ml in the culture of S. oralis, wheras being $1.4\times10^7\;to\;7.0\times10^7$ per ml in the combined culture of S. oralis and E. durans. 6. Plasmid of about 60 kb was isolated in three isolates of E. durans. These results suggested that E. durans isolated from the oral cavity inhibited the replication of S. mutans and formation of artificial plaque, while inhibiting the replication of S. oralis a little.

• Journal of dental hygiene science
• /
• v.4 no.3
• /
• pp.103-109
• /
• 2004

The present study prepared 72 test samples - 24 made of amalgam alloy, 24 of Verabond (Ni-Cr alloy) for crown and 24 of Talladium $^{TM}alloy$ for denture - according to the manufacturers' manuals and general method in consideration of the width of the mesial-distal dental crown of the lower $1^{st}$ molar and MOD cavity in clinics, put them in a 200 ml beaker containing 80 ml of artificial saliva, and measured their galvanic corrosion at distances of 0 mm, 7 mm and 40 mm after 7 days. Isolated metals in the electrolyte such as Cu, Ag, Ni, Cr, Sn, Zn and Hg were quantitatively analyzed with Inductively Coupled Plasma - Atomic Emission Spectrometer (ICP-AES, JY-50P, VG Elemental Co. France), and from the results were drawn conclusions as follows. First, Cu, Sn, Ag, Hg and Zn were highly advantageous when amalgam contacted gold alloy compared to Ni-Cr alloy for crown and Talladium alloy for denture. In addition, although gold alloy was finest in terms of oral tissue and biocompatibility, it was most disadvantageous when it was with amalgam. Second, when amalgam contacted gold alloy, heavy metals such as Ni and Cr were not isolated at all because gold alloy did not contain such elements but Sn was isolated as much as $227.1{\pm}18.0035{\mu}g/cm^2$ although it was not included in the composition either. Hg was also isolated. These elements are assumed to have been isolated from amalgam itself. Third, when amalgam alloy was apart from gold alloy 0 mm, 7 mm and 40 mm, Cu and Ag showed significance but Hg did not. This suggests that gold alloy must not be used together with amalgam, and must not be used between dissimilar prostheses regardless of distance. Fourth, when amalgam alloy contacted Ni-Cr alloy for crown, Ag was not isolated from the amalgam, but Zn, Ni, Sn, Hg and Cu were isolated in order of quantity. Significance was observed according to distance - 0 mm, 7 mm and 40 mm. Hg was not isolated but heavy metals Ni and Cr were isolated. If amalgam alloy was in the opposite arch or it was apart from Ni-Cr alloy for crown, the isolation Hg was less than that when amalgam alloy contacted Ni-Cr alloy for crown. Fifth, when amalgam alloy contacted Talladium alloy for denture, significance was observed at distances of 0mm, 7 mm and 40 mm. Hg was not isolated but heavy metals Ni and Cr were isolated. If amalgam alloy was in the opposite arch or it was apart from Talladium alloy for denture, the isolation Hg was less than that when amalgam alloy contacted Talladium alloy for denture. Sixth, according to the result of ICPES test on Cu, Sn, Ag, Hg, Zn, Ni and Cr of amalgam alloy, gold ally, Verabond and Talladium alloy when these alloys contacted artificial saliva, significance was observed in Cu and Hg. Seventh, when amalgam alloy contracted two non-precious metals Ni-Cr alloy for crown and Talladium alloy for denture in artificial saliva, significance was observed in the isolated by-products of Hg, Ni and Cr according to distance.

• The Journal of Korean Academy of Prosthodontics
• /
• v.47 no.2
• /
• pp.108-118
• /
• 2009

Statement of problem: Volume stability, microstructure reproducibility and fluidity along with compatibility with dental stone must be in consideration in order to use tissue conditioner as a material for functional impression. There are few studies concerning the influence of time factor in oral condition on surface roughness of the stone and optimal retention period in the oral cavity considering such changes in surface roughness. Purpose: The purpose of this study was to find out the influence of various kinds of tissue conditioner, its powder/liquid ratio and immersion time on surface roughness of the stone. Material and methods: Materials used in this study were the three kinds of tissue conditioners(Coe-Comfort, Visco-Gel, Soft-Liner) and were grouped into three: group R-mixed with standard powder/liquid ratio that was recommended by the manufacturers, group M-mixed with 20% more powder, group L-mixed with 20% less powder. Specimens were made with the size of 20 mm diameter and 2 mm width. Each tissue conditioner specimens were subdivided into 5 groups according to the immersion time(0 hour, 1 day, 3 days, 5 days, 7 days), completely immersed into artificial saliva and were stored under $37^{\circ}C$. Specimens of which the given immersion time elapsed were taken out and were poured with improved stone, making the stone specimens. Surface roughness of the stone specimens was measured by a profilometer. Results: Within the limitation of this study, the following results were drawn. 1. Major influencing factor on surface roughness of the stone model made from tissue conditioner was the retention period(contribution ratio($\rho$)=62.86%, P<.05) of the tissue conditioner in oral cavity to make functional impression. 2. In case of Coe-Comfort, higher mean surface roughness value of the stone model with statistical significance was observed compared to that of Soft-Liner and Visco-Gel as immersion time changes(P<.05). 3. In case of group L(less), higher mean surface roughness value of the stone model with statistical significance was observed compared to that of R(recommended) and M(more) group as immersion time changes(P<.05). Conclusion: We may conclude that as the retention period of time in oral cavity influences surface roughness of the stone model the most and as the kind of tissue conditioner and its P/L ratio may influence also, clinician should well understand the optimal retention period in oral cavity and choose the right tissue conditioner for the functional impression, thus making the functional impression with tissue conditioner usefully.

• Development and Reproduction
• /
• v.13 no.1
• /
• pp.1-11
• /
• 2009

Implantation itself is governed by an array of endocrine, paracrine and autocrine modulators, of embryonic and maternal origin. Window of implantation is the unique temporal and spatial expression of factors allows the embryo to implant via signaling, appositioning, attachment, and invasion in a specific time frame of $2{\sim}4$ days. When the embryo has arrived in the uterine cavity, a preprogrammed sequence of events occurs, which involves the production and secretion of a multitude of biochemical factors such as cytokines, growth factors, and adhesion molecules by the endometrium and the embryo, thus leading to the formation of a receptive endometrium. Cytokines such as LIF, CSF-1, and IL-1 have all been shown to play important roles in the cascade of events that leads to implantation. Integrin, L-selectin ligands, glycodelin, mucin-1, HB-EGF and pinopodes are involved in appositioning and attachment. The embryo also produces cytokines and growth factors (ILs, VEGF) and receptors for endometrial signals such as LIF, CSF-1, IGF and HB-EGF. The immune system and angiogenesis play an important role. The usefulness of these factors to assess endometrial receptivity and to estimate the prognosis for pregnancy in natural and artificial cycles remains to be proven. Integrins, pinopodes, glycodelin and LIF (from biopsies) are promising candidates; from uterine flushings, glycodelin and LIF are also candidates. The ideal serum marker is not available, but VEGF, glycodelin and CSF have some clinical implications. Further evaluation that includes larger groups of infertile women and fertile controls are needed to elucidate whether their presence in plasma, flushing fluid, or endometrial samples can be used as some kind of a screening tool to assess endometrial function and prognosis for pregnancy before and after artificial reproductive therapy. A better understanding of their function in human implantation may lead to therapeutic intervention, thereby improving the success rate in reproduction treatment. New molecular techniques are becoming available for measuring both embryonic and endometrial changes prior to and during implantation. The use of predictive sets of markers may prove to be more reliable than a single marker. Ultimately, the aim is to use these tools to increase implantation in artificial cycles and consequently improve live-birth rates.