• International Journal of Naval Architecture and Ocean Engineering
• /
• v.9 no.2
• /
• pp.227-237
• /
• 2017

In this paper, we investigated physical characteristics of an artificial supercavity generated behind an axisymmetric cavitator. Experiments for the same model were carried out at two different cavitation tunnels of the Chungnam National University and the University of Minnesota, and the results were compared and verified with each other. We measured pressures inside the cavity and observed the cavity formation by using a high-speed camera. Cavitation parameters were evaluated in considering blockage effects of the tunnel, and gravitational effects on supercavity dimensions were examined. Cavity dimensions corresponding to the unbounded cavitation number were compared. In addition, we investigated how artificial supercavitation develops according to the combination of injection positions and direction.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.9
• /
• pp.1025-1033
• /
• 2012

Fabry-Perot cavity(FPC) antennas with artificial magnetic conductor(AMC) surface are designed in order to provide scan capability by $4{\times}1$ array feed inside the cavity. The proposed antenna, excited by $4{\times}1$ thinned array, not only achieve higher directivities but also improve suppression of sidelobe level(SLL) relative to that of the thin array alone. The FPC antenna with the height of a quarter wavelength generate maximum gain of 19 dB, SLL suppression of 14 dB and maximum scan angle of $8^{\circ}$ under the feed phase difference of $90^{\circ}$ at the design frequency of 12 GHz.

• Journal of the Korean Solar Energy Society
• /
• v.30 no.5
• /
• pp.93-99
• /
• 2010

Nucleate pool boiling experiments with constant heat flux condition were performed using pure R113 for various channel heights under saturated pool condition. A circular heater of 1mm diameter, with artificial cavity in the center, fabricated using MEMS technique and the high-speed controller were used to maintain the constant heat flux. Images of bubble growth were taken at 5,000 frames per second using a high-speed CCD camera. The bubble geometry was obtained from the captured bubble images. The effects of channel height on the bubble growth behaviors were analyzed as dimensional scales for the initial and thermal growth regions. The parameters for the bubble growth behaviors were bubble radius, bubble growth rate, and bubble shapes. These phenomena require further analysis for various surface angles, but this study will provide good experimental data with constant heat flux boundary condition for such works.

• Journal of the Korean Solar Energy Society
• /
• v.29 no.4
• /
• pp.7-14
• /
• 2009

Nucleate pool boiling experiments with constant heat flux condition were performed using pure R11 and R113 for various surface angles under saturated pool condition. A circular heater of 1 mm diameter, with artificial cavity in the center, fabricated using MEMS technique and the high-speed controller were used to maintain the constant heat flux. Images of bubble growth were taken at 5,000 frames per second using a high-speed CCD camera. The bubble geometry was obtained from the captured bubble images. The effects of surface angles on the bubble growth behaviors were analyzed as dimensional scales for the initial and thermal growth regions. The parameters for the bubble growth behaviors were bubble radius, bubble growth rate, sliding velocity, bubble shape and advancing and receding contact angles. These phenomena require further analysis for various surface angles, but this study will provide good experimental data with constant heat flux boundary condition for such works.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2003.10a
• /
• pp.192-197
• /
• 2003

Three-dimensional cavity flow is analyzed with the code by using unstructured grid. Incompressible Navier-Stokes equations are used as governing equations, and governing equations are discretized by Finite Volume Method. Artificial compressibility method, proposed by Chorin, and developed by Soh, is used for coupling a pressure and a velocity. Cell-centered scheme is adopted in the code, this has the effect of having denser grid than nodal scheme when the same grid is used. Weighted Averaging scheme is used for the value at a nodal point. Cavity flow is analyzed, and this computed results are compared with the results in the research report

• Journal of the Society of Naval Architects of Korea
• /
• v.56 no.4
• /
• pp.327-334
• /
• 2019

Recently, there has been a growing interest in artificial supercavitation as a way to reduce friction drag of submerged vehicles. A cavitator plays an important role to generate the supercavity, so many studies have focused on the case of cavitator only. However, the body shape behind the cavitator affects the growth of the supercavity and this effect must be considered for evaluating the overall performance of the system. In this work, we conducted experimental investigation on artificial supercavitation generated by different combinations of the cavitator and body. We observed the supercavity pattern by using a high-speed camera and measured the pressure inside the cavity by using an absolute pressure transducer. We estimated the relation between the amount of injected air and the supercavity shape for different combinations. In summary, the disk type cavitator generates larger supercavity than that of the cone and ellipsoidal cavitators, but cavity development speed is relatively slower rather than the others. Furthermore, fore body angle plays an important role to generate the supercavity enveloping the entire body.

• International Journal of Highway Engineering
• /
• v.19 no.5
• /
• pp.69-75
• /
• 2017

PURPOSES : The purpose of this study is to evaluate different types of Ground Penetrating Radar (GPR) testing for characterizing the road cavity detection. The impulse and step-frequency-type GPR tests were conducted on a full-scale testbed with an artificial void installation. After analyzing the response signals of GPR tests for detecting the road cavity, the characteristics of each GPR response was evaluated for a suitable selection of GPR tests. METHODS : Two different types of GPR tests were performed to estimate the limitation and accuracy for detecting the cavities underneath the asphalt pavement. The GPR signal responses were obtained from the testbed with different cavity sizes and depths. The detection limitation was identified by a signal penetration depth at a given cavity for impulse and step-frequency-type GPR testing. The unique signal characteristics was also observed at cavity sections. RESULTS : The impulse-type GPR detected the 500-mm length of cavity at a depth of 1.0 m, and the step-frequency-type GPR detected the cavity up to 1.5 m. This indicates that the detection capacity of the step-frequency type is better than the impulse type. The step-frequency GPR testing also can reflect the howling phenomena that can more accurately determine the cavity. CONCLUSIONS :It is found from this study that the step-frequency GPR testing is more suitable for the road cavity detection of asphalt pavement. The use of step-frequency GPR testing shows a distinct image at the cavity occurrences.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.35 no.1
• /
• pp.45-48
• /
• 2009

Verrucous carcinoma is a distinctive form of low-grade squamous cell carcinoma. The tumor has an exophytic, cauliflower-like appearance, and usually occurs in males and tends to affect individuals over 60 years of age. It typically involves the oral cavity, larynx, esophagus and skin. Most intraoral cases involve the mandibular vestibule, the buccal mucosa and the hard palate. The cause is unknown, but most verrucous carcinomas arise from the oral mucosa in people who chronically use chewing tobacco or snuff. The treatment of oral verrucous carcinoma remains controversial. Whenever possible, surgically total excision and skin or mucosal grafting is recommended. After total excision of huge verrucous carcinoma,instead of dermal or mucosal grafting, we used artificial dermis silicone membrane. We had a good result without recurrence and present this case.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.12
• /
• pp.33-43
• /
• 2016

In order to analyze ground relaxation and cavity formation mechanism due to deteriorated sewer pipe, field test was carried out and a numerical assessments were compared with the field test results. An artificial underground cavity was intended using the ice block overlaying the buried pipe and confirmed that the cavity and relaxation of the surrounding ground were gradually formed as the ice block starts to melt down. Such mechanism was highly suspected to be involved with soil particle interlocking as a soil compaction was a typical process for the buried pipes. In exploring such mechanism numerically, commercially available DEM (Discrete Element Method) code PFC2D was used and the interlocking induced cavern behaviors were successfully simulated and compared with field test results by utilizing the clump logic imbedded in PFC code.

• Journal of the Society of Naval Architects of Korea
• /
• v.52 no.3
• /
• pp.206-221
• /
• 2015

Supercavitation is a modern technique which can be used to surround an underwater vehicle with a bubble in order to reduce the resistance of the vehicle. When the vehicle is at low speed in the deep sea, the cavitation number is relatively big and it is difficult to generate a cavity large enough to envelope the vehicle. In this condition, the artificial cavity, called ventilated cavity, can be used to solve this problem by supplying gas into the cavity and can maintain supercavitating condition. In this paper, a relationship between the ventilation gas supply rate and the cavity shape is determined. Based on the relationship a ventilation rate control is developed to maintain the supercavitating state. The performance of the ventilation control is verified with a depth change control. In addition, dynamics modeling for the supercavitating vehicle is performed by defining forces and moments acting on the vehicle body in contact with water. Simulation results show that the ventilation control can maintain the supercavity of an underwater vehicle at low speed in the deep sea.