• 전기학회논문지P
• /
• 제60권2호
• /
• pp.53-55
• /
• 2011

The printed wide band monopole antenna having characteristics of dipole by modified coplanar wave guide(CPW) ground plane is presented. We are called a slot-arm printed monopole antenna and investigated the effect of the surface currents of the radiator on ground plane. The proposed antenna is treated as two asymmetric dipoles with the included angle of $90^{\circ}$ degrees which lie along Z-direction symmetrically. It is observed that the effect of the surface currents on the radiation patterns is similar to that of the corresponding dipole. The length and width of the ground plane correspond the radius and length of the dipole respectively. This approach is also valid to general printed monopole antennas. The simulation impedance bandwidth of the proposed antenna the range of 2.4 to 4.6 [GHz] for a voltage stand wave ratio (VSWR)${\leq}$2 and got pick gain of 6 [dBi]. So the proposed antenna is satisfied the requirement of the industry science medical (ISM) band operation.

• 한국정보통신학회논문지
• /
• 제5권7호
• /
• pp.1263-1271
• /
• 2001

There are two methods in blood pressure measurement ; Invasive methode and Non-invasive method. The Invasive methode can get the 띠cod pressure measurement but, patient feel uncomfortable. So Non-invasive methode used generally. The Oscillometric method is typical Non-Invasive method. This method is commonly used to measure BP in electric sphygmomanometer and has various algorithm. In this paper it is described about a algorithm, it controls, determinates the cuff pressure, and fillers the measured BP data. This system can interface with PC(personal computer) by RS-232 and save the measured data in PC. This system deflates the cuff pressure by Solenoid valve. The main algorithm are oscillometric and maximum amplitude algorithm(MAA). MAA has various measured oscillation, it depends on patient's age, height, weight and arm circumference size. In this paper proposed system can measure Systolic BP, Diastolic BP, and Mean BP using Interpolation, Auto Reinflation algorithm.

• Journal of Species Research
• /
• 제5권3호
• /
• pp.348-350
• /
• 2016

An asteroid specimen was collected from Jumunjin, Gangwon-do in the East Sea, Korea at a depth of 50 m using fishing nets on 26 May 2013. It was identified as Pteraster militaris (O.F. $M{\ddot{u}ller$, 1776) belonging to the family Pterasteridae of the order Velatida based on morphological characteristics. This species is usually distributed in the cold boreal zone around northern Pacific and Atlantic, and is distinctly distinguished from P. tesselatus which was reported in Korean fauna: body form, length ratio of arm to disc and surface of dorsal membrane.

• 한국자기학회지
• /
• 제1권1호
• /
• pp.30-36
• /
• 1991

전기용량법에 의한 자기이방성 측정장치를 설계 제작하였다. 균이자기장 속에서 원판 또는 구형의 시료가 자기이방성에 의해 받는 토오크를 평행판 축전기의 미소용량 변화로 변환하여, 그것을 변압기 부리지 로 검출하였다. 3% Si-Fe 단결정의(100)면에 대한 입방 이방성 $K_{1}$은 $3.3{\times}10^{4}\;J/m^{3}$가 얻어졌으며, 교정에는 Ni선의 형상이방성을 이용하였다. 기타 수종의 시료에 대한 결과도 기존치와 좋은 일치를 보였다.

• 대한기계학회논문집
• /
• 제5권4호
• /
• pp.347-353
• /
• 1981

The surging stresses of the valve spring of over head valve 4 cycle engine, which is made is Korea, were computed from theoretical analysis and these values were compared with the experimental results. For calculating surging stresses of test engine valve spring. Kato's equation should be corrected by the corretion factor C which is equal to twice rocker arm level ratio. Good agreement was found to exist between the theoretical analysis and the experimental results within.+-.5 percent differences. The stress amplitudes of test valve spring at each harmonic order were determined by the experiment and by using corrected equation, The safety considerations of test valve spring were discussed.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 춘계학술대회 논문집
• /
• pp.247-250
• /
• 2006

The growing demand for more fuel-efficient vehicles to reduce energy consumption and air pollution is a challenge for the automotive industry. The characteristic properties of aluminum, high strengrth stiffness to weight ratio, good formability, good corrosion resistence, and recycling potential make it the ideal candidate to replace heavier materials in the car to respond to the weight resuction demand within the automotive industry. In this paper, A series of compression test was carried out to find the flow stress of A6082 at 300, 400 and $500^{\circ}C$, then we tried to estimate weldability, extrusion load and effective stress of die in the aluminum extrusion process through the 3D FE simulation at non-steady state for aluminum automotive parts.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1988년도 한국자동제어학술회의논문집(국내학술편); 한국전력공사연수원, 서울; 21-22 Oct. 1988
• /
• pp.16-20
• /
• 1988

This paper presents a new algorithm for solving the inverse kinematics in real-time applications. The end-tip movement of each link can be resolved into the basic resolution unit, .DELTA.l, which depends on link length, reduction ratio and resolution of the incremental encoder attached to the joint. When x- and y-axis projection of the end-tip movement are expressed in .DELTA.l unit, projectional increments .DELTA.x and .DELTA.y become -1, 0 or I by truncation. By using the incremental computation with these ternary value and some simple logic rules, a coordinate transformation can be realized. Through this approach, it should be noted that the floating-point arithmetic and the manipulation of trigonometric functions are completely eliminated. This paper demonstrates the proposed method in a parallelogram linkage type, two-link arm.

• 대한전자공학회논문지
• /
• 제16권1호
• /
• pp.22-25
• /
• 1979

Mobility Analogy에 의하면 질량은 전기 커패시턴스에 대응되며 기계회로내에서 모든 질량은 기준점에 접지되어야 한다. 따라서 접지되지 않은 전기 커패시턴스에 대응하는 부동질량은 알려지지 않고 있다. 본 논문에서는 두개의 단체지지레버와 하나의 링크, 하나의 질량 그리고 네개의 마찰이 없는 베아링으로 부동질량을 구성했으며, 이렇게 구성된 부동질량은 레버의 길이비를 변화 시키므로서 등가질량의 같을 임의로 변화시킬 수 있음을 보였다.

• 제어로봇시스템학회논문지
• /
• 제3권4호
• /
• pp.422-434
• /
• 1997

In this paper, a two-stage kinematic optimal design for a 3 degree of-freedom (DOF) excavator subsystem, which consists of boom, arm and bucket, is performed. The objective of the first stage is to find the optimal parameters of the joint-actuating mechanisms which maximize the force-torque transmission ratio between the hydraulic actuator and the rotating joint. The objective of the second stage is to find the optimal link parameters which maximize the isotropic characteristic of the excavator subsystem throughout the workspace. It is illustrated that kinematic/dynamic performances of the kinematically optimized excavator subsystem have improved compared to those of original HE280 excavator, with respect to three performance indices such as maximum load handling capacity, maximum velocity capability, and acceleration capability.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1994년도 추계학술대회 논문집
• /
• pp.617-622
• /
• 1994

In this paper, we perform a two-stage, kinematic optimal design for 3 degree-of-freedom excavator system which consists of boom, arm, and bucket. The objective of the first stage is to find the optimal joint parameters which maximize the force-torque transmission ratio between the hydraulic actuator and the rotating joint. The objective of the first stage is to find the optimal link parameters which maximize the isotropic characteristic throughout the workspace. It is illustrated that performances of the optimized excavator are improved compared to those of HE280 excavator, with respect to the described performace index and maximum load handling capacity.