• Journal of Welding and Joining
• /
• v.17 no.6
• /
• pp.38-45
• /
• 1999

Shielding gas has significant effects on arc stability, metal transfer and weld quality in the gas metal arc welding (GMAW) process. The double gas-shielded MAG(DMAG) and auxiliary gas-shielded MAG (AMAG) torches are investigated for their capability to provide argon-rich gas mixture using small amount of argon gas through the inner and auxiliary nozzles, respectively. Argon composition with the DMAG torch is calculated numerically, and compared with the measured data using the gas chromatogrphy. Gas flow pattern of the DMAG torch is calculated to change from the laminar to turbulent flow when total gas flow rate becomes larger than 4.5 liter/min at room temperature. While argon-rich shielding gas was obtained using both the AMAG and DMAG torches, the AMAG torch provides higher argon composition than the DMAG torch, which demonstrates that argon gas can be utilized more efficiently with the AMAG torch.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.323-326
• /
• 1998

The current-voltage characteristic have been measured in a gas stabilized DC arc generated in a non-transferred arc plasma torch operating on a mixture of argon and nitrogen. Relation between voltage and current to these arcs has been examined by plasma power and current under different flow rates and gas mixture ratios. Firstly, the voltage and current of arc plasma used argon was measured and secondly, in argon-nitrogen mixed gas regime, the flow rate of nitrogen was increased slowly. When the flow rate of nitrogen was increased, electrode drop of potential was increased.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.94-97
• /
• 1997

We investigated the sheet resistance properties of tungsten nitride thin films deposited by RF and DC sputtering system. It deposited at various conditions that determine the sheet resistance. The properties of the sheet resistance of these films were measured under various conditions. Sheet resistance analysed under the flow rate of the argon gas and contents of nitrogen from nitrogen-argon gas mixtures. We found that these sheet resistance were largely depend on the temperature of substrate, gas flow rate and RF power. Very high and low sheet resistance of tungsten films obtained by DC sputtering. As the increase of contents of nitrogen gas obtained from nitrogen-argon gas mixture, tungsten nitride thin films deposited by the reactive DC sputtering and the sheet resistance of these films were increased.

• Electrical & Electronic Materials
• /
• v.8 no.2
• /
• pp.196-203
• /
• 1995

We presented Tungsten and Tungsten Nitride thin films deposited by RF and DC sputtering. It deposited at various conditions that determining the resistivity and sheet resistivity by stabilizing the basic theory. We investigated properties of the resistivity and sheet resistivity of these films under various conditions, temperature of substrate, flow rate of the argon gas and content of nitrogen from nitrogen-argon mixtures. As the temperature of substrate increased and the flow rate of the argon gas decreased, the resistivities of these films reduced by structural transformation. We found that these resistivities were depend on the temperature of substrate, flow rate and electric power. Very highly resistive tungsten films obtained at 10W RF power. On the contrary, we found that films deposited by DC sputtering, from which very lowly resistive tungsten films were obtained. Tungsten nitride thin films deposited by reactive DC sputtering and the resistivities of these films increased as the content of nitrogen gas increased from nitrogen-argon mixture. And also we found the results show very good agreement, compared with experimental data.

• 전기의세계
• /
• v.26 no.2
• /
• pp.104-110
• /
• 1977

This paper investigates temperature distribution of plasma jets which used argon gas, and nitrogen gas mixed with argon as working fluids in spectroscopic method, and studies correlations between them main results are as follows; 1) The temperature at the center of plasma jet increases with are current and gas flow, and decreases with magnetic flux density along the axial direction. 2) The changing rate of temperature of plasma jet in the radial direction decreases rapidly beyond 2mm from central axis. 3) Temperature drop rate of plasma jet in the central axis direction appears most apparant beyond 13mm above the nozzle exit. 4) When argon gas mixed with a small amount of nitrogen, plasma temperature increases at same are current compared with the case of argon gas only.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.1
• /
• pp.87-94
• /
• 2023

TMCP(Thermo Mechanical Control Process) steel was continuously cast (CC) by varying the argon gas flow rate and vacuum time in the Ruhrstahl Heraeus (RH) refining process. Using the CC specimens, the distribution of the inclusions and the mechanical properties were evaluated. A lot of oxides and Al-O type inclusions were observed. The average Vickers hardness did not show a constant, but showed dispersion in a certain range. The shape and scale parameters of the CC specimen with an argon gas flow rate of 160Nm³ and a vacuum time of 12 minutes was the best. Mechanical properties (tensile strength, yield strength and elongation) were consistent with the Weibull probability distribution analysis results. The impact resistance was the best for CC specimens with an argon flow rate of 140 Nm³ and a vacuum time of 12 minutes. Although the inclusions and mechanical properties of the CC specimens were evaluated according to the argon gas flow rate and vacuum time, these values were no significant difference.

• Analytical Science and Technology
• /
• v.8 no.4
• /
• pp.443-448
• /
• 1995

Three anode configurations of six-jet, cone-jet and cylindrical-jet are tested for their analytical performance under power mode operation. The effect of pressure, power and gas flow rate on atomic absorption signals have been studied. The increase of atomic absorption signal of sample element is observed at a fixed pressure in all configurations as the gas flow rate increase up to 300-600 seem, and as the power dissipated in the glow discharge cell increase. The lower the pressure is in the glow discharge cell at a fixed discharge power and argon flow rate, the greater the absorbance of sample element is. The optimum conditions are taken from these data and a calibration curve of Cu in low-alloy steel sample is obtained. In this calibration curve, six-jet configuration shows the best analytical results varies as the sample element.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.2
• /
• pp.91-95
• /
• 2000

The effects of argon gas flow on the axial temperature gradient near the interface, the oxygen concentration, and the radial oxygen uniformity was investigated for 8-inch CZ silicon growth. As argon flow rate was increased, the temperature gradient was increased in the crystal near the crystavmelt interface and the oxygen content in the crystal was decreased. But the radial oxygen uniformity was deteriorated. It was found that argon flow is one of the important growing parameters to affect the quality of crystals such as oxygen content and uniformity.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.18 no.2
• /
• pp.169-177
• /
• 2020

Here, the stability of stainless steel 316 (SS-316) was investigated to identify its applicability in the oxide reduction process, as a component in related equipment, to produce a complicated gas mixture composed of O₂ and Cl₂ under an argon (Ar) atmosphere. The effects of the mixed gas composition were investigated at flow rates of 30 mL/min O₂, 20 mL/min O₂ + 10 mL/min Cl₂, 10 mL/min O₂ + 20 mL/min Cl₂, and 30 mL/min Cl₂, each at 600℃, during a constant argon flow rate of 170 mL/min. It was found that the corrosion of SS-316 by the chlorine gas was suppressed by the presence of oxygen, while the reaction proceeded linearly with the reaction time regardless of gas composition. Surface observation results revealed an uneven surface with circular pits in the samples that were fed mixed gases. Thermodynamic calculations proposed the combination of Fe and Ni chlorination reactions as an explanation for this pit formation phenomenon. An exponential increase in the corrosion rate was observed with an increase in the reaction temperature in a range of 300 ~ 600℃ under a flow of 30 mL/min Cl₂ + 170 mL/min Ar.

• Journal of Powder Materials
• /
• v.17 no.5
• /
• pp.379-384
• /
• 2010

In the present work, bismuth nanopowders with various particle size distributions were synthesized by controlling argon (Ar) gas flow rate and chamber pressure of a gas condensation (GC) apparatus. From the analyses of transmission electron microscopy (TEM) images and nitrogen gas adsorption results, it was found that as Ar gas flow rate increased, the specific surface area of bismuth increased and the average particles size decreased. On the other hand, as the chamber pressure increased, the specific surface area of bismuth decreased and the average particles size increased. The optimum gas flow rate and chamber pressure for the maximized electrochemical active surface area were determined to be 8 L/min and 50 torr, respectively. The bismuth nanopowders synthesized at the above condition exhibit 13.47 $m^2g^{-1}$ of specific surface area and 45.6 nm of average particles diameter.