• 한국공작기계학회논문집
• /
• 제11권5호
• /
• pp.23-29
• /
• 2002

The soldering is widely used installing the electronic element on circuit board in the common electronic device. Since the flux which improves the liquidity of solder make the electronic and chemical performance worse, the circuit board need to wash clearly. At present however no-washing is required for the cost reduction, the chemical stability, and the protection of environment. In this research, the solder liquidity depending on the power density and the pulse width is comparatively analyzed by the diffusion area method for achieving the no-flux soldering.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 춘계학술대회 논문집
• /
• pp.1760-1769
• /
• 2007

The cut slope sliding which has been frequently encountered in Pohang area has been reported due to the rapid reduction of shear strength in mudstone after being exposed to the air. Mudstone has characteristics that it has high enough strength and stiffness in a dry condition, but the strength and stiffness decrease in a wet condition with groundwater infiltration. The case study in this paper shows that mudstone which had enough strength in a boring stage has lost the strength after installing PRD steel pipe pile inducing an insufficient bearing capacity, which has been ascertained by the static load test. Test construction has been performed to investigate the most favorable method for increasing a pile bearing capacity in mudstone with various methods such as MSG (Micro Silica Grouting) around the tip and side of a pile, the perimeter grouting combined with Micro pile reinforcement, and concrete filling after tip reinforcing grouting. From the test construction, MSG has been turned out to be the most favorable method for increasing a pile bearing capacity in mudstone, which has been confirmed by the static load test.

• 제어로봇시스템학회논문지
• /
• 제18권8호
• /
• pp.794-799
• /
• 2012

The international standard, ISO-11783, was designed for the communication within an agriculture machinery. Even if it is based on the CAN (Control Area Network) protocol, its extended features which include point-to-point communication and large data transmission support show different network performance from the standard CAN. This paper proposes a dynamic priority allocation method to improve the real-time performance of ISO-11783. Computer simulation shows reduction of the deadline-missed cases and community latency via proposed algorithm.

• 한국결정성장학회지
• /
• 제22권6호
• /
• pp.269-273
• /
• 2012

Ammonia decomposition over titanium carbides were investigated using eight different samples which have been synthesized by TPR (temperature-programmed reduction) method of titanium oxide ($TiO_2$) with pure $CH_4$. The resulting materials which were synthesized using wo different heating rates and space velocity exhibited the different surface areas. These results indicated that the structural properties of these materials have been related to heating rates and space velocity employed. The titanium carbides prepared in this study proved to be active for ammonia decomposition, and the activity changed with the particle size/surface area. These showed the relationship between ammonia decomposition activity and the different active species. Compared to molybdenum carbide, the titanium carbides were one order of magnitude less active, suggesting the correlation between the activity difference and the degree of electron transfer between metals and carbon in metal carbides.

• 전력전자학회논문지
• /
• 제3권4호
• /
• pp.287-297
• /
• 1998

RPWM(Random Pulse Width Modulation)은 인버터의 스위칭 주파수를 랜덤하게 변화 시킴으로써 전압, 전류의 고조파 및 소음의 스펙트럼을 광대역에 분산시키는 PWM 기법이다. 스위칭 주파수 또는 펄스의 위치를 랜덤하게 변화시켜 고조파의 불연속적인 이산치 성분을 넓은 영역에 분산시켜 EMI, 진동 등에 좋은 효과를 낼 수 있을 뿐만 아니라, 전력소자의 스위칭에 의해 발생하는 가청 스위칭 소음을 저감할 수 있으므로 근래에 매우 각광 받고 있다. 본 연구에서는 펄스의 위치를 랜덤하게 함으로써 가청 스위칭 소음을 저감할 수 있는 새로운 RPPWM(Random Position Pulse Width Modulation) 방식의 제안 및 구현하였다. 제안된 방식은 각 3상 펄스들의 위치를 변조 구간 내의 임의의 위치에 랜덤하게 배치함으로써 RPWM을 구현하는 방식이다. 이를 위하여 16bit 공성능 마이크로 컨트롤러의 C167을 사용하여, 공각 벡터 변조에 의하여 각 변조 구간에서의 듀티비를 구한 후, 랜덤수 발생기를 이용하여 균일한 분포로 각 상의 펄스를 배치하였다. 그리고 제안된 RPPWM을 이용하여 실험한 결고, 전압, 전류 및 소음의 스텍트럼이 광대역화 되어 전력소자의 스위칭에 의해 발생하는 전동기의 가청 스위칭 소음이 현저히 저감 됨을 확인하였다.

• 한국물환경학회지
• /
• 제32권6호
• /
• pp.562-569
• /
• 2016

Recently, Low Impact Development (LID) is being used in Korea to control urban runoff and nonpoint source pollution. In this study, we evaluated the reduction of surface runoff from a study area, as the effect of connecting three bioretention as LID-BMP. Surface runoff and storage volume of bioretention is estimated by the Curve Number (CN) method. In this study, the storage volume of bioretention is divided by the volume of surface runoff and precipitation which directly enters the bioretention. The ratio of captured surface runoff volume to storage volume is highly influenced by the ratio of drainage area to surface area of bioretention. The high bioretention surface area-to-drainage area ratio captures more surface runoff. The ratio of 1.2 captures 51~54% of the total surface runoff, ranging from 5-30cm of bioretention depth; a ratio of 6.2 captures 81~85%. Three connected bioretentions could therefore captures much more runoff volume, ranging from $35.8{\sim}167.3m^3$, as compared to three disconnected bioretentions at their maximum amount of precipitation with non-effluent from the connecting three bioretentions. Hence, connecting LID-BMPs could improve the removal efficiencies of surface runoff volume and nonpoint source pollution.

• Tribology and Lubricants
• /
• 제30권6호
• /
• pp.337-342
• /
• 2014

The reduction of drag torque is an important research issue in terms of improving transmission efficiency. Drag torque in a wet clutch occurs because of the viscous drag generated by the transmission fluid in a narrow gap (clearance) between the friction plate and a separate plate. The objective of this paper is to observe the effects of the friction plate area and the clearance on the drag torque using finite element simulation. The two-phase flow of air and oil fluid is considered and modeled for the simulation. The simulation analysis reveals that as the rotational speed increases, the drag torque generally increases to a critical point and then decreases sharply at a high speed regime. The clearance between the two plates plays an important role in controlling drag torque peak. An increase in the clearance causes a decrease in shear stress; thus, the drag torque also decreases according to Newton's law of viscosity. An observation of the effect of the area of contact between transmission fluid and friction plate shows that the drag torque increases with the contact area. The flow vectors inside the flow channel present clear evidence that the velocity of the fluid flows is faster with a larger friction plate, that is, in the case of a larger contact area. Therefore, the optimum size of the friction plate should be determined carefully, considering both the clutch performance and drag reduction. It is expected that the results from this study can be very useful as a database for clutch design and to predict the drag torque for the initial design with respect to various clutch parameters.

• 로봇학회논문지
• /
• 제18권1호
• /
• pp.1-9
• /
• 2023

This paper presents an optimal path planning strategy for aerial searching and surveying of a user-designated area using multiple Unmanned Aerial Vehicles (UAVs). The method is designed to deal with a single unseparated polygonal area, regardless of polygonal convexity. By defining the search area into a set of grids, the algorithm enables UAVs to completely search without leaving unsearched space. The presented strategy consists of two main algorithmic steps: cellular decomposition and path planning stages. The cellular decomposition method divides the area to designate a conflict-free subsearch-space to an individual UAV, while accounting the assigned flight velocity, take-off and landing positions. Then, the path planning strategy forms paths based on every point located in end of each grid row. The first waypoint is chosen as the closest point from the vehicle-starting position, and it recursively updates the nearest endpoint set to generate the shortest path. The path planning policy produces four path candidates by alternating the starting point (left or right edge), and the travel direction (vertical or horizontal). The optimal-selection policy is enforced to maximize the search efficiency, which is time dependent; the policy imposes the total path-length and turning number criteria per candidate. The results demonstrate that the proposed cellular decomposition method improves the search-time efficiency. In addition, the candidate selection enhances the algorithmic efficacy toward further mission time-duration reduction. The method shows robustness against both convex and non-convex shaped search area.

• 한국소음진동공학회논문집
• /
• 제21권9호
• /
• pp.787-797
• /
• 2011

The noise in a vehicle is an important factor for customers purchasing a car. Particularly, reduction of the noise that is generated from HVAC(heating, ventilation and air conditioning) is very important since it has considerable effects on interior noise. In general, identification of noise source is crucial to reduce noise level. The complex acoustic intensity method is widely used to obtain the accurate measurement and identification of noise source. Therefore, in the previous study, noise source of HVAC was identified through experimental approach using the complex acoustic intensity method. In this study, we are intended to confirm reduced level of noise by comparing the result between before and after modification of cam curve that is based on identified noise source of HVAC. It is found out that noise source of HVAC are motor and cam area using the complex acoustic intensity method in the previous study. We performed experiments to compare noise level between before and after modification of cam curve. Especially, it can be seen that complex acoustic intensity method using both active and reactive intensity is vital in devising a strategy for comparison to noise level. Also, the vector flow of acoustic intensity was investigated to identify sound intensity distributions and energy flow in the near field of HVAC.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 A
• /
• pp.273-275
• /
• 1999

This paper presents a dynamic equivalencing method in large electric power system for stability analysis. This method of modeling simplified equivalents for parts of the network outside the study area is to evaluate the stability of a study area modeled in detail. Generators are closely coupled in an electrical sense tend to swing together in groups during disturbances, and this behavior can be exploited to reduce the size of the power system model. The characteristics of generators swing together are referred to as coherency Coherency groups whose generators state trajectory are similar to the other generators state trajectory in the same coherency group by a certain disturbance. In this paper, procedures for forming dynamic equivalents of control devices of coherency-based generating units are proposed and the aggregation of the control devices such as excitation system and governor-turbine system is accomplished by this method. This method can deal with the aggregation of the same type of control devices and combination of hydro and steam unit or the many types of excitation systems. etc. This method is shown to be efficient in reducing the number of control device of generating units with small error in the study group by result of case study presented latter part of this paper.