• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 전력전자학술대회 논문집
• /
• pp.180-184
• /
• 1998

Recently the performance of CO2 arc welding machine has been advanced significantly through the adoption of inverter circuit topology which made it possible to control the waveform of welding current and thus to suppress the spatter generation. However, the optimum waveform is still uncertain. As a first step for figuring out the promising waveforms, this study was performed to set-up the experimental system for studying the effect of waveform variables. The overal system is controlled digital controller using single chip microprocessor of 80C196KC. As a result of performance test of this system, it was demonstrated all of the waveform variables could be set individually and the generated spatter is reduced compare to conventional inverter arc welding machine.

• Journal of Advanced Marine Engineering and Technology
• /
• 제36권5호
• /
• pp.700-706
• /
• 2012

이동식발전설비에서 시동장치의 핵심기술은 피니언기어 쉬프팅 장치와 초기 기동전압을 제한하는 것이며 기존의 제품에서는 기계적 주접점을 이용한 시동 제어장치를 사용하고 있다. 하지만 완전한 피니언기어 쉬프팅 후 시동전동기의 기동의 불확실성이나 대전류에 의한 주접점의 아크손상 등의 큰 문제점을 가지고 있다. 본 연구에서는 이러한 문제점을 해결하기 위해 기동의 불확실성 제거를 위한 피니언기어 쉬프팅 제어회로, 대전류에 의한 접점의 아크손상 방지를 위해 반도체 소자를 이용한 시동 제어시스템, 직권전동기의 소프트 스타팅을 위한 기동 안전장치 등을 새롭게 설계, 제작하여 안전성과 신뢰성을 얻고자 하였다. 또한, 피니언기어 제어회로와 전동기 전원회로를 분리하여 전기적 안전성을 확보하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.700-705
• /
• 2001

The paper presents a seam tracking controller of high speed rotating arc sensor developed by microprocessor based system. The seam tracking algorithm is based on the average current value at each interval region of four phase points on one rotating cycle. To remove the noise effect for the measured current, the area during one rotating cycle is separated into four regions of front, rear, left and right. The average values at each region are calculated, using the regional current values and a low pass filter incorporating the moving average and exponential smoothing methods is adopted.

• International Journal of Precision Engineering and Manufacturing
• /
• 제4권6호
• /
• pp.20-28
• /
• 2003

This paper presents development of a high speed rotating arc sensor system using a microprocessor based controller with tracking function for a complicate curved fillet welding line, The welding tip connected to the torch body is eccentrically positioned from the centerline of the torch, The area during one rotating cycle is divided into 4 regions of front, rear, right and left in welding direction of the torch tip to determine the horizontal deviation between the welding seam and the torch position. The average value at each region is calculated using the regional current values and a low pass filter incorporated with the moving average method is implemented. The effectiveness of the developed system is proven through the experimental results for several kinds of complicate curved fillet welding lines.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2000년도 전력전자학술대회 논문집
• /
• pp.556-559
• /
• 2000

Pulse inverter-type TIG(Tungsten Inert Gas) arc welders are studied to investigate the dynamic performance of welding. Welding currents are controlled to be pulse waveforms resulting in stable are better welding performance. The hybrid-type controller is proposed to control the welding current. Todemonstrate the practical significance of our results we present some simulation results.

• 전력전자학회논문지
• /
• 제4권2호
• /
• pp.128-137
• /
• 1999

최근 전력전자기술 및 인버터 회로의 다양한 제어기법의 발달에 따라서 용접기 분야에서의 용접성능 향상에 관한 다양한 연구가 진행되고 있으며 특히{{{{ { CO}_{2 } }} 아크 용접기의 경우 용접성능을 좌우하는 스패터 발생을 최소화 하는 기법이 활발하게 연구되고 있다. 그러나 현재까지는 용접기의 출력전압을 정전압으로 제어하는 방식을 사용함에 따라 용접기의 금속이행과정을 임의로 제어하는 것이 불가능하였고, 특히 스패터가 다량으로 발생하는 저전류영역의 금속이행과정인 단락이행에서의 스패터 저감을 기대하기가 어려웠다. 따라서 본 논문에서는 마이크로프로세서를 이용한 인버터 출력전류의 파형제어기법을 사용하여 인버터 아크 용접기의 출력전류를 순시적으로 제어함에 의하여 스패터 저감, 단락주기의 안정화 및 순간단락현상 감소의 측면에서 용접성능을 개선위한 연구를 수행하였고 이상의 연구에 대한 결과를 제시하였고, 또한 인버터 아크 용접기의 AC/DC 전력변환장치로 SMR(Switched Mode Rectifier)를 사용하여 시스템을 단위역율로 운전하였으며 입력전류의 저차 고조파 억제효과를 얻을 수 있었다.

• 전자공학회논문지SC
• /
• 제44권1호
• /
• pp.12-18
• /
• 2007

본 연구에서 설계한 AFCI는 Arc 고장 차단기로서 종속된 전기 배선상의 노화, 절연 및 배선 파괴, 연결 고장, 절연과 배선에 과도한 기계적 손상으로 인한 아크고장을 검출하여 차단하는 기능을 가지고 있으며 기존 차단기가 가지고 있던 과전류에 의한 바이메탈의 만곡 특성에 의한 동작으로 차단하는 방식은 차단에 긴 시간이 걸리나 설계한 AFCI는 전자방식으로서 과부하, 과전류에 의한 기계적 , 전기적인 스트레스를 검출하여 차단하는 기능을 가진 제품으로 차단시간이 100% 이상 단축되어 전기 화재의 발생률을 낮추도록 하였다.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제48권5호
• /
• pp.257-263
• /
• 1999

Recently the performance of CO2 arc welding machine has been advanced significantly through the adoption of inverter circuit topology which made it possible to control the waveform of welding current and thus to suppress the spatter generation. However, the optimum waveform is still uncertain. As a first step for figuring out the promising waveforms, this study was performed to set-up the experimental system for studying the effect of waveform variables, The system designed in this study is a digital controller using single chip microprocessor of 80C196KC. As a result of performance test of this system, it was demonstrated all of the waveform variables could be set individually and the resultant waveforms appeared to be pretty much the same as the intended one.

• Journal of Welding and Joining
• /
• 제34권3호
• /
• pp.40-46
• /
• 2016

The digital controlled SMA welding power source having the hot start current and short circuit waveform control was developed. The inverter power controller was used an analog circuit and the short circuit waveform controller was developed using a 8-bit MCU. For the evaluation of the developed SMA welding power source it were compared with a domestic welding power sources. Using the high titanium oxide type and low hydrogen type electrodes, the characteristics of hot start and short circuit was evaluated. Developed SMA welding power source shows good start performance. Also, arc stability and low current weldability were improved by the short circuit waveform control.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1999년도 전력전자학술대회 논문집
• /
• pp.563-568
• /
• 1999

Generally the control method of wire feeding motor in welding machine has been used full-wave phase control method. The fire-angle control generates low frequency speed ripple, and it causes the output current ripple. So it results in the variation of welding condition and low welding performances such as spatter generation and bead state. For the purpose of welding performances improvement by speed controller in wire feeding motor, in this paper the constant speed control method for welding machine is proposed. The proposed system is composed of speed control loop and current control loop. As a result of experiment by using proposed constant wire feed experiment by using proposed constant wire feed speed controller, the output voltage and current waveform and metal transfer are maintained stably. And moreover the number of instantaneous short circuit occurrence is reduced remarkably.