• Applied Chemistry for Engineering
• /
• v.29 no.3
• /
• pp.258-263
• /
• 2018

This study attempted to utilize ultrafine precipitated calcium carbonate for fluoride removal from the wastewater of electronics industries. An average particle size of the calcium carbonate was $0.96{\mu}m$, and pH of the aqueous slurry was 10 with 70% in mass. The suspension solution showed approximately 2 mL/hr of the sedimentation rate. The present calcium carbonate solution could be comparable to the conventional aqueous calcium source, $Ca(OH)_2$, for the neutralization and removal of fluoride ions. Depending on the amount of an additional alkali source, less amounts of test Ca-source slurries were required to reach the solution pH of 7.0 than that of using the aqueous calcium hydroxide. It was also found from XRD analysis that more calcium fluoride precipitates were formed by the addition of calcium carbonate solution rather than that of calcium hydroxide. In addition, Minteq equilibrium modelling estimated various ion complexes of fluoride and calcium in this process.

• Journal of Biomedical Engineering Research
• /
• v.8 no.2
• /
• pp.123-134
• /
• 1987

The transport phenomena of alkali metal chlorides through poly(2 hydroxyethyl methacrylate) hydrogel membrane have been studied using electrodialysis. The hydrogel membranes were prepared by the polymerization of 2-hydroxvethyl methacrylate in the presence of 45%(V/V) H2O and ethyleneglycodimethacrylate. The initiator used in the polymerization was azobismethylisobutyrate (AMIB) prepared from azobisiobtyronitrile (AIBN) using Mortimer method. The permeability of alkali metal chlorides such LiCl, NaCl and KCI at 50 voltage was obtained. The permeability of NaCl was also observed at 30, 40, 50, and 60 voltages respectively. The concentration of solutes permeated through the membrane was measurer by flame photometry. The experimental results have been discussed with the comparison of apparent solute molecular size, the self-diffusion coefficient of solutes, the transport number of cations in aqueous solution. These indic aloes that poly(2 hydroxyethyl methacrylate) hydrogel membrane shows a specific selectivity for sodium ion.

• Bulletin of the Korean Chemical Society
• /
• v.22 no.1
• /
• pp.53-58
• /
• 2001

Sulfonated poly(phenylene sulfide) (SPPS) polymers were prepared by sulfonation of poly[methyl[4-(phenylthio) phenyl]sulfonium trifluoromethanesulfonate] (PPST) with fumic sulfonic acid (10% $SO_3-H_2SO_4$) and demethylation with aqueous NaOH solution. The equilibrium constants of ion exchange reactions between alkali metal cations ($Li^+,\;Na^+,\;and\;K^+$) and SPPS ion exchanger in organic solvents such as tetrahydrofuran (THF) and dioxane were measured. The equilibrium constants of ion exchange reactions increased as the polarity of the solvent increased, and the reaction temperature decreased. The equilibrium constants of the ion exchange reaction ($K_{eq}$) also increased in the order of $Li^+,\;Na^+,\;and\;K^+$. To elucidate the spontaneity of the exchange reaction in organic solvents, the enthalpy, entropy, and Gibbs free energy were calculated. The enthalpy of reaction ranged from -0.88 to -1.33 kcal/mol, entropy ranged from 1.42 to 4.41 cal/Kmol, and Gibbs free energy ranged from -1.03 to -2.55 kcal/mol. Therefore, the exchange reactions were spontaneous because the Gibbs free energies were negative. The SPPS ion exchanger and alkali metal ion bounding each other produced good ion exchange capability in organic solvents.

• Journal of the Korean Society for Railway
• /
• v.4 no.2
• /
• pp.62-70
• /
• 2001

Pure copper, Cu-1.1wt%Cd and ACSR(Aluminum Conductor Steel Reinforced) have been used as catenary materials of the electric railway system. Since these materials may be exposed to the corrosive environments like polluted air, acid rain and sea water, it is important to investigate the corrosion rates in various corrosive environments. The aqueous corrosion characteristics of catenary materials in aerated acid, neutral and alkali solutions were studied by using immersion corrosion tests, electrochemical measurements and analytical techniques. In order to examine corrosion characteristics according to the dissolved oxygen content, pH, chloride ion concentration ion, and the addition of Cd to Cu, a series of tests such as potentiodynamic polarization, a.c impedance spectroscopy and galvanic corrosion tests were carried out with these materials. Results showed that the addition of Cd to Cu and chloride ion in the solution have an adverse effects on the resistance to corrosion. Additionally, Galvanic currents between Al and steel wires of ACSR were confirmed by using ZRA(zero resistance ammeter) method.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.16 no.3 s.43
• /
• pp.335-344
• /
• 1992

This study was conducted to investigate the influence of addition of cetyl trimethyl ammo­nium bromide (CTAB), and amine [ethylamine (EA) or ethylene diamine (EDA)] to aqueous sodium hydroxide (NaOH) solution on polyester alkaline hydrolysis, The experimental vari­ables such as CTAB concentration, EA or EDA concentration, NaOH concentration, tempera­ture and time were compared, and the changes in physical and chemical properties of alkaline­hydrolyzed PET fabrics depending on their treated conditions were measured, The results are as follows: 1. By adding CTAB and amine in aqueous NaOH solution, increasing effect on weight loss of PET fabrics was obtained in simultaneous addition of CTAB and EDA, but not in CTAB and EA. 2. By adding CTAB & EDA simultaneously, increasing effect on weight loss was obtained regardless of EDA concentration, time and temperature, and it was more effective at lower NaOH concentration. :l. The increase of void space (or irregularly grooved surface), of softness, of wickability, of dyeability on PET fabric, and the decrease of tensile strength, of molecular weight were observed according to the weight loss on the PET fabrics. These changes were equal to all alkaline-hydrolyzed PET fabrics regardless of addition of CTAB and amine. l. There was little changes on crystallinity, thermal behavior when PET fiber was treated with ,aqueous NaOH solution with CTAB and EDA. These results supported that increasing effect on weight loss take place without inducing of fine structural change of PET fibers.

• Bulletin of the Korean Chemical Society
• /
• v.23 no.4
• /
• pp.549-554
• /
• 2002

Thermosensitive poly(organophosphazenes) bearing methoxy-poly(ethylene glycol) (MPEG) and alkylamines as substituents have been synthesized and characterized by elemental analysis, NMR spectroscopy, GPC, and DSC. All the polymers exhibited crystallinity, which was probably induced by the MPEG side chain of the polymers. All the polymers exhibited the lower critical solution temperature (LCSTs) in the range of 28 to $94^{\circ}C$ depending on several factors such as mole ratio of the substituents, kinds of PEG and alkylamines. The higher content of MPEG and shorter chain length of alkylamines of the polymers afforded the higher LCST. The LCSTs of the polymers exhibited almost concentration-independent behavior in the range of 3-30 wt % of the polymers in aqueous solutions. The polymers showed the higher LCSTs in the acidic solutions than in the neutral and basic solutions. The ionic strength of the polymer solution affected the LCST, which decreased with increased NaCl concentration. The polymer bearing almost equimolar substitutuents with the -N-P-N- unit has shown the LCST more sensitive to NaCl and pH than that with the -N-P-O- unit. The polymers were found to degrade in acidic solution but be very stable in alkali solution as well as in the buffer solution of pH 7.4.

• Journal of Pharmaceutical Investigation
• /
• v.34 no.4
• /
• pp.269-274
• /
• 2004

To enhance the solubility and stability of lansoprazole (LAN), new proton pump inhibitor, we were prepared various molar ratio of inclusion complex with $2-hydroxypropyl-{\beta}-cyclodextrin$ (HPCD) and organic alkali agent, meglumine (MEG). Inclusion complex formation of LAN with HPCD was investigated by Differential Scanning Calorimetry and X-ray diffractometry. The aqueous solubilities of inclusion complexes, and the stabilities of 1:4 and 1:5 inclusion complexes in aqueous solutions containing different concentrations of MEG were examined. The stability of 1:5 LAN-HPCD inclusion complex containing MEG, which was equaled to amount of LAN, was performed in 0.9% NaCl and 5% dextrose solution. The formation of inclusion complex of LAN with HPCD was $A_L$ type and the molar ratio of complex was 1:1. The stability constant was $41.557\;M^{-1}$. As molar ratio of LAN to HPCD was increased, solubility of inclusion complex was increased. 1:5 LAN-HPCD inclusion complex was more stable than 1:4 LAN-HPCD inclusion complex. And as contained MEG amount in LAN solution was increased, stability of 1:4 and 1:5 LAN-HPCD inclusion complexes was improved. Also stability of 1:5 LAN-HPCD-MEG inclusion complex in 0.9% NaCl solution and 5% dextrose solution was similar to it in water at room temperature, but it was unstable at $40^{\circ}C$.

• Applied Chemistry for Engineering
• /
• v.23 no.3
• /
• pp.284-288
• /
• 2012

This work deals with the chemical characterization of glycine aqueous solution in $CO_2$ absorption. Three alkali elements were impregnated into the glycine in order to facilitate the formation of amino functionalities. The analysis by IR revealed the transformation of ammonium ions to the amino group. In addition, the NMR analysis showed that the substitution of metal cations to the chemical shift of hydrogen and carbon atoms in glycine; in order of lithium glycinate, sodium glycinate and potassium glycinate depending on the electro negativity. Meanwhile, the $CO_2$ absorption at room temperature was the highest in primary amine solution, but at the increasing temperature sodium glycinate could capture more $CO_2$ than that of the pure amine solution.

• Applied Chemistry for Engineering
• /
• v.8 no.2
• /
• pp.237-245
• /
• 1997

A DEAE-chitin was prepared with DEAE HCl in an aqueous alkali-chitin solution. The resulting DEAE-chitin exhibited a highly improved affinity to water and organic solvents, It was N-deacetylated by heating in aqueous 10% sodium hydroxide containing sodium borohydride for 9h at $80^{\circ}C$ to produce DEAE-chitosan. These conditions were milder than those for the N-deacetylation of chitin. In order to increase its cationic character, the DEAE-chitin was treated with ethyl halide to give TEAE-chitin. The structural changes in the chitin derivatives were confirmed by using both FT-IR and $^1H$ NMR, and their flocculating behavior, in kaoline suspension showed the optimum property at a weak alkaline pH and 8 ppm concentration of resin conditions.

• Journal of the Korean Applied Science and Technology
• /
• v.10 no.2
• /
• pp.41-47
• /
• 1993

Chitin was isolated from crab shells by modified Hackman's method, which was treated again with aqueous sodium hydroxide solution to give alkali chitin(sodium alkoxide of chitin). And after, the alkali chitin is allowed to react with monochloroacetic acid to synthesize 6-O-(carboxymethyl) chitin [CM-Chitin] under diminished pressure. In order to synthesize high performance CM-Chitin as hygroscopic agent, it was measured that the yield and degree of subsititution of each CM-Chitin according to molar ratio(monochloroacetic acid equivalent mol/N-acetyl-D-glucosamine residue) and their moisture-absorption and moisture-release properties were measured and compared with those of hyaluronic acid. The moisture-absorption and moisture-release properties of CM-Chitin, especially 0.8 in degree of substitution, were found quite similar to those of hyaluronic acid. The preliminary results show that CM-Chitin might be used as hygroscopic agent instead of hyaluronic acid in field of cosmetics.