• Journal of Korea Multimedia Society
• /
• v.9 no.12
• /
• pp.1628-1635
• /
• 2006

A new frequency-modulated m-sequence correlation technique was described. It has. been seen that the frequency modulation scheme leads to higher signal-to-noise ratio than direct sequencing and less hardware effort than PSK modulation scheme. The operating frequency of the correlation system was deduced. The optimal frequency for the frequency-modulated m-sequence correlation system should be 1.35 times of the center frequency of the transducer. The application of this correlation technique to electromagnetic ultrasonic system was computer-simulated.

• Management & Information Systems Review
• /
• v.21
• /
• pp.169-187
• /
• 2007

Today, the principle of competition is being applied to Non-profit sector also. It is necessary for relevant persons in charge to learn the knowledge and technique about marketing technique endlessly in connection with the development of donor out of the development of social welfare resource which is being embossed as main pending problem at the point of time when the role of private sector about welfare service increased and the criterion of competition and evaluation among institutions was introduced. Especially, as for the application of marketing technique to utilize internet to have big marketing potential, the efforts for the realization and application of positive marketing to be suitable for the real situation of each institution is necessary in connection with the donor development of social welfare institution. In this study tried to examine the charge of method to develop donor which is based on the development of information technique and the popularization of internet from the viewpoint of internet marketing and suggest the basic data about the present situation of donor marketing to use the effective scheme for internet marketing.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.3
• /
• pp.950-956
• /
• 2014

Special purpose sensor design using MEMS (Micro-Electro-Mechanical Systems) technique is commonly used in Nondestructive Testing (NDT) research for the evaluation of existing structures and for the safety control and requirements. Various sensors and network have been developed for general infrastructures as well as safety-critical applications, e.g., aerospace, defense, and nuclear system, etc. In this paper, one of sensor technique using Fiber Bragg Gratings (FBG) and Finite Element Method (FEM) evaluation is discussed. The experimental setup and data collection technique is also demonstrated. The factors influencing test result and the advantages/limitations of this technique are also reviewed using various methods.

• The Journal of the Korea Contents Association
• /
• v.12 no.8
• /
• pp.96-104
• /
• 2012

The reusability problems in the existing object-oriented development method and component development method is the problem that should be also resolved in the mobile development. Changing the function in mobile applications need to upgrade the entire mobile application, which can cause problems in mobile application in conjunction with other applications within the device. Thus, the changable functions in mobile application should be developed by considering their reusability. In this paper, we propose the customization technique that can be improved reusability for a variety of requirements of mobile application. We propose the self-adaptable customization technique that can change dynamically for the function to require changes by applying the data variability among variabilities.

• Journal of KIISE:Software and Applications
• /
• v.29 no.12
• /
• pp.895-906
• /
• 2002

Due to increased concern about the distributed web application, the interest in EJB - server-side Java component architecture that enables to make out Business Logic without writing codes related to complicated distributed framework - is also increasing. Despite of these increased interest, However, efforts for reliability of these systems have been insufficient. Thus, in this paper, we propose specification technique for applying DbC approach, which can elevate the reliability of software in the Object-Oriented system development, in writing formal specification of EJB-based application. Through this specification technique, developers can gain reliability in the EJB-based application development.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.792-793
• /
• 2005

Circuit testing process is very important in IC Manufacturing there are two ways in research for circuit testing improvement. These are ATPG Tool Design and Test simulation application. We are interested in how to use parallel technique such as one-side communication, parallel IO and dynamic Process with data partition for circuit testing improvement and we use one-side communication technique in this paper. The parallel ATPG Tool can reduce the test pattern sets of the circuit that is designed in laboratory for make sure that the fault is not occur. After that, we use result for parallel circuit test simulation to find fault between designed circuit and tested circuit. From the experiment, We use less execution time than non-parallel Process. And we can set more parameter for less test size. Previous experiment we can't do it because some parameter will affect much waste time. But in the research, if we use the best ATPG Tool can optimize to least test sets and parallel circuit testing application will not work. Because there are too little test set for circuit testing application. In this paper we use a standard sequential circuit of ISCAS89.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.775-782
• /
• 2004

Recently, the cases which are constructed close by neighboring structure or underground structure are on the increase to get the utmost out of the land exploitation of underground space in the downtown area. As the building becomes larger, the excavation depth is getting deep, and the excavation area is getting, wide too. These are frequent occasions that the application of Strut or Anchor method is difficult, because of site boundary, civil application and the ground condition. Therefore, to solve these problem, we analyze and compare design with measuring data, change the design factor and show the improvement of course through the application of self-supported diaphragm wall using counterfort technique which is a new method. It is expected to be a contribution to the suitable exploitation method of construction.

• KIEAE Journal
• /
• v.17 no.1
• /
• pp.5-13
• /
• 2017

Purpose: This study, by comprehensively the characteristics of new Hanok application techniques with the proposed site application technology in the course of the design changes that have been accumulated through Hanok technology development the second stage business, by analyzing the range of reflection, new Considering the direction reflects the efficiency of the new Hanok application techniques. Method: new Hanok application technology, it was been established through research and development of large 1 new Hanok technology it has been proposed through the "site-specific application techniques" and 2 builders and designers "space-time proposed technique" Analysis of the case, at the center of the design changes, the land the body of laws and regulations, the requirements of the public buildings, compared to the construction method and the like for the reduction of construction costs, new Hanok applied technology in the process of change by it There was analyzed whether acceleration on the range and step which is reflected in the design Result: The result of new Hanok applied technology was built through the demonstration build business case, process another major technology, foundation, woodwork, walls, roof, has been reflected in the ceiling construction, the inclusion of items in the proposed technique of construction , it was applied to the main steps in general, except for other construction work landscaping. Application techniques and construction proposal technology research team has presented, show the difference between the scope and method. With significance effort to improve the unreasonable traditional methods of these core processes that can be reflected in the field repeated the construction proposed technique as a result of the utility that can be applied for substantial construction.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.442-447
• /
• 2005

This paper presents an application of overlapping-grid technique for probe feeding simulation. The overlapping grid technique is used to solve contour path problem. In this technique, field interpolation is very important to make communication between two coordinates. By applying overlapping-grid technique, error of contour path in probe feeding simulation is reduced.

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.171-174
• /
• 1998

The development of the high-frequency induction-heating for 2700kW power range intend to make localization at forging and rolling mill part by technical innovation. And, the development makes to increase our's competitive power at technique, quality and cost. This paper describes the heart of high-frequency induction-heating technique, switching technique, a few problem in common using as an unsatisfied technique, load adjustment technique, system control, diagnostic system, and auto-interface etc.