• 한국세라믹학회지
• /
• 제32권1호
• /
• pp.57-62
• /
• 1995

The coating condition of reproducible anti-reflective coating film and the light transmittance characteristics of the prepared anti-reflective coating glass were investigated as a study for the preparation of single-layer anti-reflective coating glasss. In case of coating with the sol in which the solvent was substituted with the ethanol with the addition of 0.1 mol HNO3, the coated glass showed the minimum value of the refractive index of 1.464, light transmittance of 94.2% at 550nm standard wavelength which is 3.2% higher than that of the parent glass, and the reflectance in the entire wave range of visible light. The refractive index represented its minimum at the sol concentration of 1.0 mol per 100mols of water and the higher the sol concentration, the higher the refractive index, resulting in the decrease of the light transmitance. The production condition of the reproducible anti-reflective coating on glass with the maximum transmittance of 94.2% was 4cm/min of withdrawal speed, 40$0^{\circ}C$ and 1 hour of heat treatment temperature and time, resulting in the film thickness of 94nm.

• 한국수소및신에너지학회논문집
• /
• 제25권2호
• /
• pp.145-150
• /
• 2014

This study investigates the preparation of anti-reflective (AR) coating film to improve the efficiency of solar cell. The AR coating film was successfully obtained by dip-coating with AR coatings prepared by sol-gel method. Fluoroalkylsilane was additionally introduced into the coatings to give the self-cleaning effect of AR coating film. We performed the abrasion test, pencil scratch hardness test and cross-cut test to identify the mechanical strength of AR coating film. As the results, the transmittance of AR coating films with 9.07, 18.13 and 27.20 of IPA/MTMS molar ratios were 93.1, 93.6 and 95.3%, respectively. The water contact angle and transmittance of AR coating film increased by the introduction of hydrophobicity. The prepared AR coating film shows the high level of abrasion, hardness and adhesion. The IPA/MTMS molar ratio of 27.20 and the withdrawing speed range of 0.20 ~ 0.28cm/sec are the optimal coating condition in terms of the transmittance and mechanical strength of AR coating film.

• 공업화학
• /
• 제26권4호
• /
• pp.400-405
• /
• 2015

Tetraethylorthosilicate (TEOS)를 전구체로서 이용하여 제조된 기존의 반사방지(AR; anti-reflective) 코팅막은 대부분 수분을 쉽게 흡수할 뿐만 아니라 낮은 내마모성을 갖는다. 본 연구에서는 AR 코팅막의 투과율, 소수성 및 내마모성을 향상할 목적으로 전구체로서 methyltrimethoxysilane (MTMS)를 사용하고 불소 실란, 산 촉매, 염기 촉매 및 산-염기 2단계 촉매를 첨가하여 다양한 AR 코팅막을 제조하였다. 제조된 AR 코팅막은 UV-Vis, 접촉각 측정기, AFM, 연필경도 및 부착성 시험을 통해 특성을 분석하였다. 그 결과, 경화온도가 $300^{\circ}C$일 때 코팅되지 않은 유리 기판의 투과율은 90.5%인 반면, AR 코팅된 유리 기판의 투과율은 94.8%로 증가하였다. 불소 실란을 첨가한 경우, 소수성이 크게 향상되었음을 나타내듯이 AR 코팅막 표면에서의 접촉각은 $96.3^{\circ}$에서 $108^{\circ}$까지 증가하였다. AR 코팅막의 내마모성은 산 촉매에 의해 향상되었으며, 그것의 투과율은 염기 촉매에 의해 증가하였다. 산-염기 2단계 촉매 반응에 의해 제조한 AR 코팅막의 경우, 상승 효과에 의해 촉매의 도입 없이 제조된 AR 코팅막과 비교하여 투과율 및 내마모성이 향상되었다.

• 한국재료학회지
• /
• 제30권3호
• /
• pp.131-135
• /
• 2020

Silver nanowire (AgNW) networks have been adopted as a front electrode in Cu(In,Ga)Se2 (CIGS) thin film solar cells due to their low cost and compatibility with the solution process. When an AgNW network is applied to a CIGS thin film solar cell, reflection loss can increase because the CdS layer, with a relatively high refractive index (n ~ 2.5 at 550 nm), is exposed to air. To resolve the issue, we apply solution-processed ZnO nanorods to the AgNW network as an anti-reflective coating. To obtain high performance of the optical and electrical properties of the ZnO nanorod and AgNW network composite, we optimize the process parameters - the spin coating of AgNWs and the concentration of zinc nitrate and hexamethylene tetramine (HMT - to fabricate ZnO nanorods. We verify that 10 mM of zinc nitrate and HMT show the lowest reflectance and 10% cell efficiency increase when applied to CIGS thin film solar cells.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.449-449
• /
• 2007

OLED has many advantages of low voltage operation, self radiation, light weight, thin thickness, wide view angle and fast response time to overcome existing liquid crystal display (LCD)'s weakness. Therefore, It draws attention as promising display and has already developed for manufactured goods. Also, OLED is regarded as a only substitute of flexible display with a thin display. A considerable portion of the light originating film emissive centers buried in a solid film never escapes due to internal reflection at the air-film interface and is scattered as edge emission or dissipated within the solid film This is one of the major reasons why the luminous power efficiency of OLED remains low, in spite of research progress in OLED. Although several ways of overcoming this difficulty have been reported, no comprehensive method has been proposed yet. In this paper, we propose that use of anti-reflective coating layers.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 광주전남지부
• /
• pp.103-106
• /
• 2006

Semiconductor laser diode has a reflective facet in a both-ends side fundamentally. Laser performance for improving, Anti-Reflection and High-reflection coating on the facet of semiconductor laser diode. To prevent internal feedback from both facets for realizing superluminescent diode and reducing the reflection-induced intensity noise of laser diode, it's key techniques are AR/HR coatings. In the study AR coating film were manufactured by Ion-Assisted Deposition(IAD) system. Then manufactured coating film measurement electrical properties(L-I-V, Se, Resistor) and Optical properties (wavelength FFP)

• 한국표면공학회지
• /
• 제50권5호
• /
• pp.345-351
• /
• 2017

A double-layered anti-reflective coating with hydrophilic/abrasion-resistant properties was studied using anatase titanium dioxide($TiO_2$) and silicon oxycarbide($SiO_xC_y$) thin film. $TiO_2$ and $SiO_xC_y$ thin films were sequentially deposited on a glass substrate by DC sputtering and PECVD, respectively. The optical properties were measured by UV-Vis-NIR spectrophotometer. The abrasion-resistance and the hydrophilicity were observed by a taber abrasion tester and a contact angle analyzer, respectively. The $TiO_2/SiO_xC_y$ double-layer thin film had an average transmittance of 91.3%, which was improved by 10% in the visible light region (400 to 800 nm) than that of the $TiO_2$ single-layer thin film. The contact angle of $TiO_2/SiO_xC_y$ film was $6.9^{\circ}$ right after UV exposure. After 9 days from the exposure, the contact angle was $10.2^{\circ}$, which was $33^{\circ}$ lower than that of the $TiO_2$ single-layer film. By the abrasion test, $SiO_xC_y$ film showed a superior abrasion-resistance to the $TiO_2$ film. Consequently, the $TiO_2/SiO_xC_y$ double-layer film has achieved superior anti-reflection, hydrophilicity, and abrasion resistance over the $TiO_2$ or $SiO_xC_y$ single-layer film.

• 공업화학
• /
• 제30권3호
• /
• pp.358-364
• /
• 2019

반사 방지(anti-reflective; AR) 코팅막의 광학 특성 및 내오염성을 향상하기 위하여 tetraethylorthosilicate (TEOS)/염기 및 methyltrimethoxysilane (MTMS)/산 혼성 용액의 혼합비를 변화시키며 다양한 AR 코팅막을 제조하였다. 제조된 AR 코팅막은 UV-Vis, 접촉각 측정기, AFM, FT-IR 및 연필 경도 시험을 통해 특성을 분석하였다. MTMS/산 용액의 함량이 10 wt%인 혼성 용액으로 제조한 AR 코팅막에서 유리 기판은 매우 우수한 광학 특성(97.2%의 투과율), 우수한 내오염성($121^{\circ}$의 물 접촉각 및 $90^{\circ}$의 $CH_2I_2$ 접촉각), 중간 정도의 기계적 강도(4 H의 연필 경도)를 나타내었다. 특히 우수한 내오염성은 기판의 표면 위에서 혼성 용액 내 소량의 MTMS/산 용액으로부터 유래된 메틸기($-CH_3$)의 고른 분산에 기인한 것으로 고려되었다. 연필 경도 시험 결과로부터, AR 코팅막의 기계적 강도는 MTMS/산 용액의 함량이 증가할수록 향상되는 것으로 나타났다.

• 한국재료학회지
• /
• 제15권5호
• /
• pp.285-292
• /
• 2005

Anti-reflection film was coated by using spherical silica nano colloids. Silica colloid sol was reserved between two inclined slide glasses by capillary force, and particles were convectively stacked to form a film onto the substrate as the water evaporates. As the sliding speed increased, the thickness of the film decreased and the wavelength at the maximum transmittance decreased. The microstructure observed by SEM showed that silica particles were nearly close packed, which enabled the calculation of the effective refractive index of the film. The film thickness was measured by proffer and calculated from the wavelength of maximum transmittance and the effective refractive index. The effective refractive index of the film could be controlled by a subtle controlling of the coating speed and by mixing two different sized silica particles. When the 100 nm and 50 m particles were mixed at 4:1-5:1 volume ratio, the maximum transmittance of $95.2\%$ for one-sided coating was obtained. This is the one that has increased by $3.8\%$ compared to bare glass substrate, and shows that $99.0\%$ of transmittance or $1.0\%$ of reflectance can be achieved by the simple process if both sides of the substrate are coated.

• 공업화학
• /
• 제21권5호
• /
• pp.564-569
• /
• 2010

박막 및 디스플레이 분야에서는 광학 부품소재의 우수한 광 투과성과 투명성을 요구하는 수요가 증가함에 따라 우수한 반사방지 특성의 부여에 대하여 관심이 집중되고 있는 실정이다. 본 연구에서는 반사방지 기능을 부여하기 위하여 졸-겔법에 의한 수열합성법을 통하여 기저 물질 표면에 산화알루미늄을 나노 크기 꽃 형태의 프레임 구조를 가진 단일 산화물층을 형성시키고자 하였다. 코팅 층 시편의 특성은 UV-Vis 분광기, FT-IR 분광기, XRD 및 FE-SEM을 이용하여 분석하였다. 알루미나 졸이 코팅된 시편들의 모폴로지는 수열합성의 온도와 시간 및 초음파 제공에 의해 조절되도록 하였다. 꽃 형태의 나노 프레임 구조 형태로 구성된 코팅 층에서 높은 광투과율과 반사방지특성이 발현되었다.