• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.1
• /
• pp.33-39
• /
• 2008

In this paper, a broadband rectangular reflector antenna with 16-array elements for WiBro/WiMAX band(2.3${\sim}$3.5 GHz) is designed, and its radiation characteristics are investigated. The designed antenna is composed of the IBBD(Integrated Balun Bow-tie Dipole) elements and has the feed circuit at the rear of the reflector to reduce the unwanted electromagnetic wave from it. To confirm the broadband characteristics of the designed antenna, test antenna is fabricated and its radiation characteristics are measured, compared with calculated results. The measured results show good agreement with the calculated results. As a result of measurements, 1.8GHz of bandwidth(VSWR<1.6) is achieved at $2.06{\sim}3.89GHz$ and the antenna gain over 10.3 dBi. We confirm that the designed antenna can be used as a broadband antenna for WiBro/WiMAX.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.7
• /
• pp.597-605
• /
• 2015

Negative impedance converter(NIC)-based non-Foster impedance matching is proposed for an electrically small antenna. The antenna considered in this work is a resistively loaded vee dipole(RVD) antenna, which has considerable reflection at the feed point because of its large negative input reactance. The non-Foster matching circuit built near the feed point consists of two-stage NIC circuit and a capacitor connected between the stages. The NIC is realized by using operational amplifiers(op-amps) and resistors. The circuit is designed by considering of the input impedance according to the finite open-loop gain of the practical NICs. The stability test of the impedance-matched RVD antenna is performed. The non- Foster matching circuit is implemented with the RVD antenna. The measured impedance demonstrates that the proposed non-Foster matching circuit effectively reduces the input reactance of the RVD antenna.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.9
• /
• pp.940-946
• /
• 2010

In this paper, we proposed the internal antenna on PCB(Planar Circuit Board) for achieving WWAN(Wireless Wide Area Network) operation in the laptop computer. The proposed antenna has a metal structure instead of printed pattern on PCB to improve the antenna characteristics for GSM850/900 bands. Compared to PCB embedded antenna without metal structure, the proposed antenna occupies similar area of $74{\times}11{\times}0.5\;mm^3$ with before and the bandwidth of the proposed one for GSM850/900 bands is increased 13 MHz than before. Further we confirmed that the proposed antenna has higher radiation gain of -4.45~-2.29 dBi for GSM850/900 bands than PCB embedded antenna without metal structure.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.10
• /
• pp.820-826
• /
• 2013

In this paper, a compact and wideband CLAS(Conformal Load bearing Antenna Structure) was studied using smart skin technique. In order to satisfy the electrical performance of the CLAS antenna, the proposed CLAS antenna is composed of conductive mesh, face-sheet, radiator, honeycomb, housing. Especially, radiator is composed of composite magneto-dielectric material and radiating element etched on the PCB (Printed Circuit Board). The radiating element is inserted into the composite magneto-dielectric material and has sloted Folded LP(Log Periodic) structure. By fabricated composite magneto-dielectric, the resonance frequency is decreased and the impedance matching characteristics is improved. We verified that the antenna has wideband characteristics and compact size using the antenna test results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.3 s.118
• /
• pp.298-304
• /
• 2007

In this paper, the antenna which has a multiband operation (GSM850, EGSM, DCS1800, USPCS, W-CDMA) is proposed. This antenna was designed by the commercial software HFSS 3-D EM simulator, and it is organized by using a meander branch structure which has a via and lines on FR-4$(\varepsilon_r=4.4)$ substrate. Especially, it has a gap feeding structure which makes good operation at overall bandwidth. The designed antenna is manufactured by PCB processing, and measured by using a network analyzer and a test chamber. The manufactured antenna with the dimension of 8 mm width, 20 mm height and 3.2 mm thickness is able to applied as an internal antenna for multiband mobile phones.

• Journal of the Korean Society for Railway
• /
• v.18 no.2
• /
• pp.105-110
• /
• 2015

This paper presents a $4{\times}1$ beam-forming reader antenna system for a new type of RFID based train position detection technology. The required beamwidth of the reader antenna is analytically expressed for different train speeds. The proposed antenna system consists of four rectangular patch elements and two switching couplers which are designed, without any impedance matching networks, for two different antenna modes. The switching coupler is a rectangular quadrature coupler with Pin diodes connecting its center line and the ground plane. The beamwidth of the antenna when the diodes are off and on is $18^{\circ}$ and $39^{\circ}$, respectively. The proposed antenna system will be used for a real train test in the near future.

• The Journal of Korean Institute of Next Generation Computing
• /
• v.13 no.1
• /
• pp.7-21
• /
• 2017

Multiple antenna techniques employed in fourth generation mobile communication systems are affected on their performance mostly by transmission environments and antenna configurations. The performance of the indoor LTE(Long-term Evolution) MIMO(multiple input multiple output) has been rigorously evaluated with considering various diversity transmission schemes and propagation conditions in the paper. Specifically, MAC TP(medium access control throughput) and LTE system parameters related to the MIMO technique are analyzed for several indoor propagation conditions. The performance comparison between multiple antenna diversity mode and single antenna mode has been derived as well. The results performed in the paper give the guideline on antenna configurations of polarization diversity in LTE 2×2 MIMO for various indoor channel environments, and possibly are exploited by network operators and antenna manufacturers.

• Journal of Space Technology and Applications
• /
• v.1 no.1
• /
• pp.33-40
• /
• 2021

Based on the requirements of a total weight of 42 kg or less, the NEXTSat-2 SAR (synthetic aperture radar) system was developed. As the NEXTSat-2 is a small-sized satellite, the SAR system was designed to account for about 40% of the dry mass of the payload relative to the total mass. Among the major components of the SAR system - which are an antenna, an RF transceiver, a baseband signal processor, and a power unit - a part with a particularly large dry mass is the antenna, the core of the SAR system. Whereas various selections are possible in consideration of gain and efficiency when designing the antenna, the micro-strip patch array antenna was adopted by reflecting the dry mass, power, and resolution required by the NEXTSat-2 project. In order to meet the mission requirement of the NEXTSat-2, the antenna was developed with a frequency of 9.65 GHz, a gain of 42.7 dBi, and a return loss of -15 dB. The performance of the antenna was verified by conducting a field test onboard the vehicle.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.5
• /
• pp.27-36
• /
• 2012

We propose a new scheme combining the calibration of the path imperfections and the compensation of HPA nonlinearity in the downlink OFDM smart antenna systems. We use a two term third-order polynomial (without second-order term) and the indirect learning architecture for calibration and compensation, to make each path of the antenna array have equal characteristics. We test our scheme with computer simulations. The result shows that, with the addition of only one third-order term, the adverse nonlinear effects as well as the those of linear imperfections can be effectively compensated.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1568-1572
• /
• 2004

This paper proposes a new online calibration algorithm for the array antenna system. As you know, the several previous calibration methods for the mutual coupling did not estimate but measure mutual coupling effect at the real or test-bed system directly. Therefore we suggest some idea to compensate the calibration errors due to mutual coupling effect and mismatch in cables and electronic modules without the off-line calibration. In this work, we can calibrate the array antenna system under the operation of the system using Independent Component Analysis(ICA). This is what is called an online calibration. As you know, the ICA method has permutation and scaling problems. However, we solve problems of the ICA method and apply it to the calibration of an array antenna. The method simultaneously estimates the DOA(Direction of Arrival) of the signals, and calibrates the array for that specific angle. The proposed algorithm is evaluated by computer simulation and its behavior is illustrated by a numerical example.