• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.2
• /
• pp.13-18
• /
• 2008

In this paper, we consider an amplifying-and-forward(AF) dual-hop relaying system where the source node transmits to a destination node with the help of R relay nodes. We assume that the source node equips M transmit antennas, but only one antenna is equipped at the each node of relay and destination. The outage probabilities are presented when the transmit maximum-ratio-combining(MRC) is used at the source-relay(S-R) links, and the best relay selection, which selects only one relay that contributes the most to the received signal-to-noise ratio(SNR) as active relay, is combined. Simulation results validate these analytical results.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.11 no.4
• /
• pp.229-237
• /
• 2011

In this paper, a 60 GHz LTCC SiP with low-power CMOS OOK modulator and demodulator is presented. The 60 GHz modulator is designed in a 90-nm CMOS process. The modulator uses a current reuse technique and only consumes 14.4-mW of DC power in the on-state. The measured data rate is up to 2 Gb/s. The 60 GHz OOK demodulator is designed in a 130nm CMOS process. The demodulator consists of a gain boosting detector and a baseband amplifier, and it recovers up to 5 Gb/s while consuming low DC power of 14.7 mW. The fabricated 60 GHz modulator and demodulator are fully integrated in an LTCC SiP with 1 by 2 patch antenna. With the LTCC SiP, 648 Mb/s wireless video transmission was successfully demonstrated at wireless distance of 20-cm.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.4
• /
• pp.542-550
• /
• 2001

In this paper, a channel combiner is designed to combine two adjacent digital TV channels without interference to transmit these channels with one broadband antenna. A constant impedance type combiner, consisting of two identical bandpass filters and two identical 3 dB power combiners, is chosen as a channel combiner. The bandpass filter used in the channel combiner also suppresses out-of-band signal caused by digital transmitter's non-linearity. H-plane type bandpass filters and branch-line fewer combiners are adopted in the design. The simulated results of the designed bandpass filter and power combiner show excellent agreement with the theoretical results. Finally, a channel combiner is designed by combining filters with rover combiners and the characteristics are simulated. It is shown that the designed channel combiner shows excellent performance.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.4
• /
• pp.450-461
• /
• 1998

The spatial distribution of multipath fading using miniaturized experimental setup was analyzed. The spatial Fourier transform was carried out for the analysis of the period of fading and we could find out spatial frequency component of fading. Thus the analysis using this method shows the validity of miniaturized experimental setup. The miniaturized experimental setup was made by 5 times reducing of the real size. The simulation was performed at 2 GHz and the measurement was carried out at 10 GHz. Automatic antenna moving system was made for exact measurement of the multipath fading. Both simulated and measured results in miniaturized experimental setup were shown by electric field distribution and spatial frequency density distribution curves.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.3
• /
• pp.352-359
• /
• 2001

We propose the row method that is able to consider the SAR compliance test from the very beginning step of developing the mobile phone. The reason this new method is plausible is that we adopt the certified FDTD for the reliability of calculation, utilizing 1 mm high resolution model that is to model the phantom and the mobile phone almost identically to the reality. In this paper we introduce the process that will apply the proposed method in order to reduce the SAR of the mobile phone that has been problematic in satisfying the SAR compliance test. It results in dropping in the SAR that we keep the mobile phone or its antenna while we use it. Therefore here we make a claim as fellows. When we develop the new mobile phone, we should use the computer simulation combining the CAD design and radiation pattern rather than make a prototype and then use the trial and error method. Moreover the former way leads us to boost up the developing efficiency and reduce the cost.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.1
• /
• pp.26-36
• /
• 2000

A circularly polarized $12\times12$ array with application in the satellite communications is designed at 10 GHz. The radiator is an aperture-coupled ring patch, which is suitable of large arrays. The element spacing of the array is chosen to be $0.7\lambda_0$to maintain the main beam in the broadside direction. The array is a sequential array constructed on a series-parallel feed network to obtain high gain and low axial ratio. Measurement results for the array, acquired by experiments in the compact range of POSTECH, showed a directivity of 27.88 dB, a high gain of 25.55 dB, an efficiency of 60%, an axial ratio of 1.74 dB, and a side-lobe level of -13 dB. The bandwidth of the array was 43% when the VSWR was 2, and the bandwidth of the axial ratio was 16%.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.4
• /
• pp.506-514
• /
• 1998

The design and fabrication of X-band(11.7~12 GHz) 2-stage monolithic microwave integrated circuit(MMIC) low noise amplifier (LNA) for active antenna are presented using $0.15{\mu}m\times140{\mu}m$ AlGaAs/InGaAs/GaAs pseudomorphic high electron mobility transistor (P-HEMT). In each stage of the LNA, a series feedback by using a source inductor is used for both input matching and good stability. The measurement results are achieved as an input return loss under -17 dB, an output return loss under -15dB, a noise figure of 1.3dB, and a gain of 17 dB at X-band. This results almost concur with a design results except noise figure(NF). The chip size of the MMIC LNA is $1.43\times1.27$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.2
• /
• pp.182-190
• /
• 2011

A amplitude modulation(AM) range measuring system utilizes the phase difference of the modulated envelope of the reflected signal to measure the distance. It is known that the AM system has a problem in accuracy due to antenna leakage signals and spurious reflection signals, but an AM range measurement system using an active reflector, which shifts the frequency bands, has been proposed in order to minimize the measurement errors due to spurious signals. In this paper, a new phase measurement module for the AM range measurement system, which enables to measure long distance with good accuracy, is proposed. The modulation frequency is alternatively selected between 8 and 1 MHz, and the measured distance range with this module is up to 150 m within 2 cm accuracy. A JK flip-flop circuit is used for higher phase accuracy, and an XOR circuit is used to cover long distance.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.2
• /
• pp.199-207
• /
• 2011

A Ku-band low noise amplifier has been designed and fabricated by using 0.25 um SiGe BiCMOS process. The developed Ku-band LNA RFIC which has been designed with hetero-junction bipolar transistor(HBT) in the BiCMOS process have noise figure about 2.0 dB and linear gain over 19 dB in the frequency range from 9 GHz to 14 GHz. Optimization technique for p-tap value and electro-magnetic(EM) simulation technique had been used to overcome the inaccuracy in the PDK provided from the foundry service company and to supply the insufficient inductor library. The finally fabricated low noise amplifier of two fabrication runs has been implemented with the size of $0.65\;mm{\times}0.55\;mm$. The pure amplifier circuit layout with the reduced size of $0.4\;mm{\times}0.4\;mm$ without the input and output RF pads and DC bais pads has been incorporated as low noise amplication stages in the multi-function RFIC for the active phased array antenna of Ku-band satellite VSAT.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.1
• /
• pp.106-112
• /
• 2013

In this paper, human exposure of wireless devices was analyzed for various positions of the transmitter. The scenario for the position of the transmitting antenna was decided after discussion with ADD(Agency for Defense Development), and Korean male phantom model developed by ETRI were used to conduct simulations. The SAR values were analyzed by changing the position of the transmitter, and compared with Korean EMF regulations and ICNIRP guidelines. Additionally, human exposure was also investigated for two typical postures which can be posed by war-fighter.