• Journal of the Korean Ceramic Society
• /
• v.52 no.5
• /
• pp.338-343
• /
• 2015

To prevent an interfacial reaction between the anode and the electrolyte layer during the conventional high-temperature co-firing process, an anode-supported type cell with a thin-film electrolyte was fabricated by low-temperature ceramic thick film coating process. Ni-GDC cermet composite was used as the anode material and YSZ was used as the electrolyte material. Open circuit voltage and maximum power density were found to strongly depend on the surface uniformity of the anode functional layer. By optimizing the microstructure of the anode functional layer, the open circuit voltage and maximum powder density of the cell increased to 1.11 V and $1.35W/cm^2$, respectively, at $750^{\circ}C$. When a GDC barrier layer was applied between the YSZ electrolyte and the LSCF cathode, the cell showed good stability, with almost no degradation up to 100 h. Anode-supported type SOFCs with high performance and good stability were fabricated using a coating process.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.45 no.4
• /
• pp.562-567
• /
• 1996

A new lateral MOS controlled thyristor, named Shorted Anode LMCT(SA-LMCT), is proposed and analyzed by a two-dimensional device simulation. The device structure employs the implanted n+ layer which shorts the p+ anode together by a common metal electrode and provides a electron conduction path during turn-off period. The turn-off is achieved by not only diverting the hole current through the p+ cathode short but also providing the electron conduction path from the n-base into the n+ anode electrode. In addition, the modified shorted anode LMCT, which has an n+ short junction located inside the p+ anode junction, is also presented. It is shown that the modified SA-LMCT enjoys the advantage of no snap-back behavior in the forward characteristics with little sacrificing of the forward voltage drop. The simulation result shows that the turn-off times of SA-LMCT can be reduced by one-forth and the maximum controllable current density may be increased by 45 times at the expense of 0.34 V forward voltage drop as compared with conventional LMCT. (author). 11 refs., 6 figs., 1 tab.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.491-492
• /
• 2006

We report on the fabrication of organic-based flexible display using an amorphous IZO anode grown at room temperature. The IZO anode films were grown by a conventional DC reactive sputtering on polycarbonate (PC) substrate at room temperature using a synthesized IZO target in a Ar/$O_2$ ambient. X-ray diffraction examination results show that the IZO anode film grown at room temperature is complete amorphous structure due to low substrate temperature. It is shown that the $Ir(ppy)_3$ doped flexible organic light emitting diode (OLED) fabricated on the IZO anode exhibit comparable current-voltage-luminance characteristics to OLED fabricated on conventional ITO/glass substrate. These findings indicate that the IZO anode film grown on PC substrate is a promising anode materials for the fabrication of organic based flexible displays.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.401-402
• /
• 2007

The preparation and characteristics of ITO anode films grown using a linear facing target sputtering (FTS) technique for use in organic light emitting diodes (OLED) and flexible OLED is described. The electrical, optical, and work function of the ITO anode, which was prepared by linear FTS at room temperature, were comparable to those of commercial ITO anode films. In particular, linear FTS-grown ITO films shows very smooth surface without defects such as pin hole and cracks due to low substrate temperature. Furthermore OLED with the linear FTS-grown ITO anode film shows comparable electrical and optical properties to those of OLED with the commercial crystalline-ITO anode film. This suggested that linear FTS is promising thin film technology for preparing high quality anode film in OLEDs and flexible OLEDs.

• Transactions of the Korean hydrogen and new energy society
• /
• v.17 no.1
• /
• pp.82-89
• /
• 2006

The redox behaviors of anode-supported flat tube for solid oxide fuel cell has been studied. The mass change of the extruded NiO/YSZ anode flat tube during redox cycling was examined by thermogravimetric analysis(TGA). The result of TGA was shown a rapidly mass change in the range of $455\;-\;670^{\circ}C$ and the reoxidation of the NiO/YSZ anode was almost completed at $750^{\circ}C$. The starting temperature of reoxidation and the maximum temperature of oxidation rate decreased with increasing the reoxidation cycle, which is attributed to the increased porosity caused by volume change. Bending strengths of the NiO/YSZ anode after redox cycling were 96 - 80 MPa and the bending strength decreased slightly with increasing the redox cycle. On the other hand, the bending strength of the NiO/YSZ anode with electrolyte showed 130 MPa after first redox cycling but decreased rapidly with increasing the redox cycle. From the results of the bending test and the microstructure observation, we conclude that the crack initiation of the electrolyte-coated NiO/YSZ anode was induced easily at interface of electrolyte/anode tube and propagated cross the electrolyte.

• Journal of the Korean Society of Safety
• /
• v.32 no.6
• /
• pp.54-60
• /
• 2017

A railway rail will be corroded by the repetitive sea wind and fog in the splash and tidal zone such as Youngjong grand bridge. And these rusts of rail could be increased by increasing service period, and it frequently occurred the safety accidents or disorders in electrical problem. In this study, the sacrificial anode cathodic protection method was proposed as a measures for reducing the corrosion of the railway rails in the oceanic climate conditions. As the results of immersion test using the salt water during four months, the sacrificial anode cathodic protection method using the aluminum anode(Al-anode) was evaluated that a distinct effect on corrosion reduction in the rails. Therefore the sacrificial anode cathodic protection method was experimentally proven that a disorders in aspects electric and signal of railway operation condition such as direct fixation track system in Youngjong grand bridge could be prevented by reducing rust falling from the rail. In addition, the installation conditions of the anodes directly affect the transmission range of corrosion potential, the sectional loss of anode, and the corrosion reduction effect. Therefore, to expect the corrosion reduction effect of rails under the oceanic climate conditions for railway track, it was important to adopted the appropriate spacing of anode installation by considering the actual field conditions.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.565-565
• /
• 2013

Free burning arcs where the work piece acts as an anode are frequently used for a number of applications. Our investigation is exclusively concerned with a simplified unified model of arcs and anode under steady state conditions at atmospheric pressure. The model is used to make predictions of arc and anode temperatures and arc voltage for a 200 A arc in argon. The computed temperatures along the axis between the cathode tip and the anode surface compare well the measured data. This knowledge of free burning arcfeatures can play a role in developing the atmospheric plasma systems, however, further investigation should include the modelling of Cu evaporation from anode and non-LTE situation near electrodes for more realistic calculations.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.968-971
• /
• 2002

Hole injection characteristics have been investigated with various metal anodes such as Ni, Pt, Cu, and AI for the top emission polymer light emitting diodes (PLEDs). Devices were composed of metal anode, Poly(3,4-ethylenedioxythiophene) doped with polystyrene sultponated acid (PEDT:PSS), poly [2-methoxy-5-(2-ethylhexyoxy)-1,4-phenylene-vinylene] (MEH-PPV) and Al cathode. The hole injection from ITO anode has been also investigated for the comparison. The I-V characteristics of the PLEDs with different metal anodes were measured. The work function of the anode is strongly related to the hole injection of the device. The current density of the device with Ni anode with higher work function was higher than that of the device with ITO or AI anode at the same operating voltage.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.1284-1287
• /
• 1996

전기도금공장 ANODE 투입 및 추출 자동화 사업은 ANODE 자동투입 Robot이 개발되어 적용되기전까지는 국내에서 적용된 사례가 전혀 없었고 선진제철소에서 일부 적용된 사례가 있는 것으로만 알고 추진되었던 사업이다. 이번에 개발하여 현장에 적용한 ANODE 자동투입 robot은 가반중량이 300kg이나 되는 이동형 특수 robot으로 국산화개발품이지만 성능의 신뢰성이 입증되지 않는 상태에서 추진되었기 때문에 위험 부담성이 컸으며 완전자동화가 되기까지 많은 시행착오를 겪었다. 시행착오의 주요원인으로는 현장여건 즉 설비의 간섭, FUME에 의한 robot의 고장 또한 robot 자체의 설계 miss등 무수히 많았다. 이번 ANODE 자동투입 robot 개발 및 현장 적용으로 향후 확대 적용시 시행착오에 의한 문제점을 최소화 할수 있는 대책을 수립할수 있는 좋은 기회가 주여져 96.12.E 준공을 목표로 2차분 ANODE투입 자동화 사업이 진행중에 있으며 1차분과 시스템을 통합하여 보다 완벽한 자동화시스템을 구축할 예정이며 97년도에는 포항제철소로 확대 적용할 예정이다.

• Journal of the Korean institute of surface engineering
• /
• v.27 no.3
• /
• pp.166-175
• /
• 1994

The effect of Co addition on the electrochemical performance and structural stability of porous Ni anode for molten carbonate fuel cell(MCFC) was evaluated by the anodic polarization and the sintering test in the simulated MCFC anode condition ($650^{\circ}C$, 80% $H_2$+20%$CO_2$). The anode current density ranged from 110mA/$cm^2$ to 144mA/$cm^2$ was obtained at +100mV overpotential by additions of Co up to 10 wt.%. The sintering resistance of Ni-Co anodes was higher than that of the pure Ni anode. The increase of sintering resistance seemed to be to the lower diffusion coefficient of Co than that of Ni.