• Journal of the Korean Ceramic Society
• /
• v.34 no.10
• /
• pp.1021-1026
• /
• 1997

RuO2 thin film has reasonably good conductivity and stiffness and it is thought to substitute for the cantilever beam made up of Pt and Si3N4 double layers in microactuators. Therefore, anisotopic Si etching was performed using RuO2 thin film as a mask layer in 25 wt. % TMAH water solution. In the etching temperature ranging from 6$0^{\circ}C$ to 75$^{\circ}C$, the etch rates of all the crystallographic directions increased linearly as the etching temperature increased. The etch rate ratio(selectivity) of [111]/[100] which varied from 0.08 to 0.14, was not sensitive to temperature. The activation energies for [110] direction, [100] direction and [111] direction were 0.50, 0.66 and 1.04eV, respectively. RuO2 cantilever beam with a clean surface was formed at the etching temperatures of 6$0^{\circ}C$ and $65^{\circ}C$. But the damages due to formation of pin holes on RuO2 surface were observed beyond 7$0^{\circ}C$. The tensile stress of RuO2 thin films caused the cantilever bending upward. As a result, it was demonstrated that the formation of conducting oxide RuO2 cantilever beam which can replace the role of an electrode and supporting layer could be possible by TMAH solution.

• Electrical & Electronic Materials
• /
• v.8 no.1
• /
• pp.90-94
• /
• 1995

Reactive Ion Etching(RIE) of Si$_{3}$N$_{4}$ in a CF$_{4}$/O$_{2}$ gas plasma exhibits such good anisotropic etching properties that it is widely employed in current VLSI technology. However, the RIE process can cause serious damage to the silicon surface under the Si$_{3}$N$_{4}$ layer. When an atmospheric pressure chemical vapor deposited(APCVD) SiO$_{2}$ layer is used as a etch-stop material for Si$_{3}$N$_{4}$, it seems inevitable to get a good etch selectivity of Si$_{3}$N$_{4}$ with respect to SiO$_{2}$. Therefore, we have undertaken thorough study of the dependence of the etch rate of Si$_{3}$N$_{4}$ plasmas on $O_{2}$ dilution, RF power, and chamber pressure. The etch selectivity of Si$_{3}$N$_{4}$ with respect to SiO$_{2}$ has been obtained its value of 2.13 at the RF power of 150 W and the pressure of 110 mTorr in CF$_{4}$ gas plasma diluted with 25% $O_{2}$ by flow rate.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.11
• /
• pp.1686-1690
• /
• 1989

Using the anisotropic etching characteristics of N2H4-H2O solutions, Si diaphragm was fabricated for the integrated sensors. The optimal composition and temperature of the etching solution in (100) Si etching process was established to be 50mol% N2H4 in H2O at 105\ulcorner\ulcorner for both higher etch rate (=2.6\ulcorner/min) and better surface quality of etched (100) planes. Based on the above optimal etching condition, the electrochemical etch-stop technique was employed to form n-type Si diaphragm having a thickness of 20\ulcorner and the thickness of diapragm could exactly be controlled to 20\ulcorner\ulcorner.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.397-400
• /
• 1997

This paper presentes the characteristics of Si anisotropic etching and electrochemical etch-stop in aqueous TMAH/IPA/pyrazine solution. (100) Si etching rate of 0.747 $\mu\textrm{m}$/min which faster 86% than TMAH 25 wt.%/IPA 17 vol.% solution was obtained using best etching condition at TMAH 25 wt.%/IPA 17 vol.%/pyrazine 0.1 g and the etching rate of (100) Si was decreased with more additive quantity of pyrazine. I-V curve of p-type Si in TMAH/IPA/pyrazine was obtained. OCP(Open Circuit Potential) and PP(Passivation Potential) were -2 V and -0.9 V, respectively. Si diaphragms were obtained by electrochemical etch-stop in aqueous TMAH/IPA/pyrazine solution.

• Journal of the Semiconductor & Display Technology
• /
• v.10 no.4
• /
• pp.31-35
• /
• 2011

For high efficiency of Si-cells, Si wafers were textured by the KOH and NaOH etching solution to decreas the reflectance at surfaces of the cells. The textured surfaces were shown various types such as isotropic and anisotropic depending on the etching solution. The reflectance at sample of an anisotropic form with pyramid type was lower than that of isotropic form. The surface with isotropic form of general tiny circles on the surface increased the efficiency, however, the reflectance of it was increased. The efficiency was increased on surface with low roughness.

• Journal of the Korean Vacuum Society
• /
• v.9 no.2
• /
• pp.99-101
• /
• 2000

The fabrication of the submicron size hole has been interesting due to the potential application of the near field optical sensor or liquid metal ion source. The 2 micron size dot array was photolithographically patterned. After formation of the V-groove shape by anisotropic KOH etching, dry oxidation at $1000^{\circ}C$ for 600 minutes was followed. In this procedure, the orientation dependent oxide growth was performed to have an etch-mask for dry etching. The reactive ion etching by the inductively coupled plasma (ICP) system was performed in order to etch ~90 nm $SiO_2$ layer at the bottom of the V-groove and to etch the Si at the bottom. The negative ion energy would enhance the anisotropic etching by the $Cl_2$ gas. After etching, the remaining thickness of the oxide on the Si(111) surface was measured to be ~130 nm by scanning electron microscopy. The etched Si aperture can be used for NSOM sensor.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.79-79
• /
• 1999

The varous techniques for fabrication of si or metal tip as a field emission electron source have been reported due to great potential capabilities of flat panel display application. In this report, 240nm thermal oxide was initially grown at the p-type (100) (5-25 ohm-cm) 4 inch Si wafer and 310nm Si3N4 thin layer was deposited using low pressure chemical vapor deposition technique(LPCVD). The 2 micron size dot array was photolithographically patterned. The KOH anisotropic etching of the silicon substrate was utilized to provide V-groove formation. After formation of the V-groove shape, dry oxidation at 100$0^{\circ}C$ for 600 minutes was followed. In this procedure, the orientation dependent oxide growth was performed to have a etch-mask for dry etching. The thicknesses of the grown oxides on the (111) surface and on the (100) etch stop surface were found to be ~330nm and ~90nm, respectively. The reactive ion etching by 100 watt, 9 mtorr, 40 sccm Cl2 feed gas using inductively coupled plasma (ICP) system was performed in order to etch ~90nm SiO layer on the bottom of the etch stop and to etch the Si layer on the bottom. The 300 watt RF power was connected to the substrate in order to supply ~(-500)eV. The negative ion energy would enhance the directional anisotropic etching of the Cl2 RIE. After etching, remaining thickness of the oxide on the (111) was measured to be ~130nm by scanning electron microscopy.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.295-298
• /
• 1989

Using the anisotropic etching characteristics or $N_2H_4-H_2O$ solution, Si diaphragm was fabricated for the integrated sensor. The optimal composition and temperature of the solution in Si etching process was established to be 50mol% $N_2H_4$ in water at $105{\pm}2^{\circ}C$ for both higher etch rate(=$2.6{\mu}m/min$) and better surface quality of etched {100} planes. Under the optimal etching condition, the electrochemical etch stop technique was employed to form Si diaphragm for pressure sensor and diaphragm thickness was exactly controlled to $20{\pm}2{\mu}m$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.7
• /
• pp.616-621
• /
• 2009

Reduction of optical losses in crystalline silicon solar cells by surface modification is one of the most important issues of silicon photovoltaics. Porous Si layers on the front surface of textured Si substrates have been investigated with the aim of improving the optical losses of the solar cells, because an anti-reflection coating(ARC) and a surface passivation can be obtained simultaneously in one process. We have demonstrated the feasibility of a very efficient porous Si ARC layer, prepared by a simple, cost effective, electrochemical etching method. Silicon p-type CZ (100) oriented wafers were textured by anisotropic etching in sodium carbonate solution. Then, the porous Si layers were formed by electrochemical etching in HF solutions. After that, the properties of porous Si in terms of morphology, structure and reflectance are summarized. The structure of porous Si layers was investigated with SEM. The formation of a nanoporous Si layer about 100nm thick on the textured silicon wafer result in a reflectance lower than 5% in the wavelength region from 500 to 900nm. Such a surface modification allows improving the Si solar cell characteristics. An efficiency of 13.4% is achieved on a monocrystalline silicon solar cell using the electrochemical technique.

• Journal of the Microelectronics and Packaging Society
• /
• v.11 no.4 s.33
• /
• pp.81-86
• /
• 2004

A new method to improve the wet etching characteristics is described. The anisotropic wet-etching of (100) Si with megasonic wave has been studied in KOH solution. Etching characteristics of p-type (100) 6 inch Si have been explored with and without megasonic irradiation. It has been observed that megasonic irradiation improves the characteristics of wet etching such as an etch uniformity and surface roughness. The etching uniformity on the whole wafer with and without megasonic irradiation were less than ${\pm}1\%$ and more than $20\%$, respectively. The initial root-mean-square roughness($R_{rms}$) of single crystal silicon is 0.23 nm. It has been reported that the roughnesses with magnetic stirring and ultrasonic agitation were 566 nm and 66 nm, respectively. Comparing with the results, etching with megasonic irradiation achieved the Rrms of 1.7 nm on the surface after the $37{\mu}m$ of etching depth. Wet etching of silicon with megasonic irradiation can maintain nearly the original surface roughness after etching process. The results have verified that the megasonic irradiation is an effective way to improve the etching characteristics such as etch uniformity and surface roughness.