• 한국통신학회논문지
• /
• 제7권4호
• /
• pp.161-166
• /
• 1982

本論文에서는 단일 모우드 광섬유의 고유 birefringence 및 twisting에 의한 birefringence 특성에 대해 理論的 分析과 實驗을 하였다. 分析過程에서 단일 모우드 광섬유는 선형 지연기로 모델링하였으며 측정결과 순수birefringence는 약 2.57 /m로 나타났다. 그리고 twisting에 의한 회전을 섭동이론에 의해 理論的으로 分析한 結果 회전각을 광섬유의 비틀림각에 선형적으로 변화되었으며 이러한 理論的結果는 實驗的結果와 거의 일치함이 分析되었다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.I
• /
• pp.547-550
• /
• 2005

• 한국운동역학회지
• /
• 제28권2호
• /
• pp.69-78
• /
• 2018

Objective: The purpose of this study was to investigate the feasibility of a new vault technique through a kinematic comparison of the YANG Hak Seon and Yeo 2 vaults. Method: The photographic images of the YANG Hak Seon and Yeo 2 vaults were collected using a high-speed camera, and their kinematic characteristics were analyzed using three-dimensional image analysis. Results: During the post-flight phase of the Yeo 2 and YANG Hak Seon vaults, the time of flight, height of flight, and flight distance were similar. At the peak of the post-flight phase, the trunk rotation angle of the YANG Hak Seon vault rotated $457^{\circ}$ more than did the Yeo 2 vault. During the post-flight descending period, the twist velocity of the trunk was much faster with the YANG Hak Seon vault ($1,278^{\circ}/s$) than with the Yeo 2 vault ($1,016^{\circ}/s$). Conclusion: To succeed in the new technique, the average twist velocity during post-flight must be maintained at $1,058^{\circ}/s$ and the twist velocity must be increased from the ascending phase.

• 소성∙가공
• /
• 제22권8호
• /
• pp.477-485
• /
• 2013

This paper aims to evaluate quantitatively the springback characteristics that evolve in the sheet metal forming of an S-rail in order to understand the reasons of shape inaccuracy and to find a remedy. The geometrical springback is classified into six modes: angle change of punch and die shoulders, wall curl, ridge curl, section twist, and axial twist. The measuring method for each springback mode is suggested and quantitative measurements were made to determine the tendency towards shape accuracy. Forming experiments were conducted with four types of steel sheets that have different tensile strengths, which were 340MPa, 440MPa, 590MPa and 780MPa, in order to evaluate the effect of the tensile strength and the bead shape on the springback behavior. Springback tendencies show that they are greatly affected by the tensile strength of the sheet and the shape of the tools. Almost all springback modes except the section twist and the axial twist show a linearly increasing trend as the tensile strength of the sheet increases. The results can be used as basic data for design and for compensation of the press die geometry when forming high strength steels which exhibit large amounts of springback.

• 한국운동역학회지
• /
• 제24권4호
• /
• pp.317-327
• /
• 2014

As a single subject study, it was purposed to investigate kinematic differences between Yang Hak Seon vault (i.e., handspring forward and salto forward straight with triple twist, Yang-1 vault hereafter) and Tsukahara $1260^{\circ}$ twist with salto forward straight (Yang-2 vault hereafter) in gymnastics. Yang Hak-Seon (23 years, 160 cm, and 52 kg) voluntarily participated in this study. Motion capture system, consisting of fourteen cameras, were used to measure Yang-2 vault with the sampling rate of 200 Hz. Twenty six reflective markers were placed on major anatomical points of 15 body segments. Successful two trials of Yang-2 vault were collected and analyzed for the comparison. Compared Yang-1 results were based on the previous study of Park and Song (2012). Results indicated superior linear kinematics of Yang-1 vault to those of Yang-2 vault before the touchdown of vault table. However, Yang-2 vault revealed superior angular kinematics to Yang 1 vault showing more trunk twist angle (a triple and a half twist) and its faster angular velocity during the airborne. The Yang 2 vault could has advantage of increasing angular motion than Yang 1 vault as a result of a half turn off the springboard onto the vault table and a sequential touchdown of the hands.

• 소성∙가공
• /
• 제23권8호
• /
• pp.501-506
• /
• 2014

Progressive shearing with blanking dies is commonly employed to produce large quantities of tiny sheet metal electronic parts. Sheet metal pins, which are narrow and long, that are sheared with a progressive die set are often twisted. The twist in the sheet metal pins, which usually occurs in the final shearing operation, generally decreases with increasing blank holding force. The blank holding forces in all shearing operations are not the same because of different shearing positions and areas. In the current study, the optimal layout of the springs in a progressive die set to minimize the twist of the sheet metal pin is proposed. In order to find the holding force acting on the tiny narrow blanks produced with the proposed springs during the shearing process, the equivalent area method is used in the structural analysis. The shearing of the sheet-metal pin was simulated to compute the twist angle associated with the blank holding force. The constraint condition satisfying the pre-set blank holding force from the previous shearing operations was imposed. A design of experiments (DOE) was numerically implemented by analyzing the progressive die structure and by simulating the shearing process. From the meta-model created from the experimental results and by using a quadratic response surface method (PQRSM), the optimal layout of the springs was determined. The twist of sheet metal pin associated with the optimal layout of the springs found in the current study was compared with that of an existing progressive die to obtain a minimal amount of twist.

• 한국공간구조학회논문집
• /
• 제21권4호
• /
• pp.23-30
• /
• 2021

In this paper, a twisted shape structure with an elevation form favorable to the resistance of vibration caused by wind loads is selected from among the forms of high-rise buildings. The analytical model is a square, triangular, and hexagonal plane with a plane rotation angle of one degree from 0 to 3 degrees per each story. As a result of the analysis, as the twist angle increased, story drift ratio is increased. Responses with different eccentricity rates were shown by analytical models. Therefore planar shapes designed symmetrically to the horizontal axis of X and Y are considered advantageous for eccentricity and torsion deformation. In the case of the bending moment of the column, the response was amplified in the column supporting the base floor, the roof floor, the floor in which the cross-section of the vertical member changes, and the floor having the same number of nodes as the base floor. Finally, the axial force response of the column is determined to be absolutely affected by the gravity load compared to the lateral load.

• 한국운동역학회지
• /
• 제13권3호
• /
• pp.81-98
• /
• 2003

The purpose of this study is to closely examine kinematic characteristics by jump phase of Li Xiaopeng motion in horse vaulting and provide the training data. In doing so, as a result of analyzing kinematic variables through 3-dimensional cinematographic using the high-speed video camera to Li Xiaopeng motion first performed at the men's vault competition at the 14th Busan Asian Games, the following conclusion was obtained. 1. It was indicated that at the post-flight, the increase of flight time and height and twisting rotational velocity has a decisive effect on the increase of twist displacement. And Li Xiaopeng motion showed longer flight time and higher flight height than Ropez motion with the same twist displacement of entire movement. Also the rotational displacement of the trunk at peak of COG was much short of $360^{\circ}$(one rotation) but twist displacement showed $606^{\circ}$. Likewise, Li Xiaopeng motion was indicated to concentrate on twist movement in the early flight. 2. It was indicated that at the landing, Li Xiaopeng motion gets the hip to move back, the trunk to stand up and the horizontal velocity of COG to slow down. This is thought to be the performance of sufficient landing, resulting from large security of rotational displacement of airborne and twist displacement. 3. It was indicated that at the board contact, Li Xiaopeng motion made a rapid rotation uprighting the trunk to recover slowing velocity caused by jumping with the horse in the back, and has already twisted the trunk nearly close to $40^{\circ}$ at board contact. Under the premise that elasticity is generated without the change of the feet contacting the board, it will give an aid to the rotation and twist of pre-flight. Thus, in the round-oH phase, the tap of waist according to the fraction and extension of hip joint and arm push is thought to be very important. 4. It was indicated that at the pre-flight, Li Xiaopeng motion showed bigger movement than the techniques of precedented studies rushing to the horse, and overcomes the concern of relatively low power of jump through the rapid rotation of the trunk. Li Xiaopeng motion secured much twist distance, increased rotational distance with the trunk bent forward, resulting in the effect of rushing to the horse. 5. At horse contact, Li Xiaopeng motion makes a short-time contact, and maintains horse take-off angle close to vertical, contributing to the increase of post-flight time and height. This is thought to be resulted from rapid move toward movement direction along with the rotational velocity of trunk rapidly earned prior to horse contact, and little shave of rotation axis according to twist motion because of effective twist in the same direction.

• 한국생산제조학회지
• /
• 제6권4호
• /
• pp.138-146
• /
• 1997

The optimal drill helix angle, point angle, and cutting conditions are recommended in the study so as to maximize the drilling performance by investigating the experimental reaults concerning with the state of chip formation, roundness of machined holes, and geometry of projected burr at hole exit, which are examined under the conditions of various helix angles, drill point angles of twist drill, cutting speeds, and feeds in operional parameters. In the easiness of chip escape, the helical type of chip is producted when a helix angle is 30$^{\circ}$, drill point angle 118$^{\circ}$, 140$^{\circ}$and feed is st between 0.1 and 0.15mm/rev. Roundness of machined hole is improved when the helix angle is 37$^{\circ}$, drill point angle is 118$^{\circ}$, and feed is 0.15mm/rev. The height of projected burr at the button of machined hole increases when the drill point angle and helix angle becomes large.

• Fibers and Polymers
• /
• 제4권4호
• /
• pp.161-168
• /
• 2003

An investigation of the dimensionless torque in the newly developed cone drum twister texturing mechanism is reported. The cone drum twister is one of the outer surface contacting friction-twisting devices in false-twist texturing. In this cone drum twister, a filament yam passes over the surface of the cone drum that rotates by the passing yarn without a special driving device. This research is composed of the theoretical analysis of the false twisting mechanism and the experimental analysis at room temperature. The equations have been derived which shows interrelationship of the conical angle of cone drum, the wrapping angle, the drag angle, and the yam helix angle. Theoretical values of dimensionless torque were calculated and were compared with the experimental results. It is shown that, as the conical angle and the projected wrapping angle increased, the dimensionless torque also increased. But the conical angle was reached to ${30.75}^{\circ}C$, the dimensionless torque decreased.