• 산업경영시스템학회지
• /
• 제35권4호
• /
• pp.24-32
• /
• 2012

Of many approaches to reduce motion analysis errors, the compensation method of anatomical landmarks estimates the position of anatomical landmarks during motion. The method models the position of anatomical landmarks with joint angle or skin marker displacement using the data of the so-called dynamic calibration in which anatomical landmark positions are calibrated in ad hoc motions. Then the anatomical landmark positions are calibrated in target motions using the model. This study applies the compensation methods with joint angle and skin marker displacement to three lower extremity motions (walking, sit-to-stand/stand-to-sit, and step up/down) in ten healthy males and compares their performance. To compare the performance of the methods, two sets of kinematic variables were calculated using different two marker clusters, and the difference was obtained. Results showed that the compensation method with skin marker displacement had less differences by 30~60% compared to without compensation. And, it had significantly less difference in some kinematic variables (7 of 18) by 25~40% compared to the compensation method with joint angle. This study supports that compensation with skin marker displacement reduced the motion analysis STA errors more reliably than with joint angle in lower extremity motion analysis.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2008년도 동계학술발표회 논문집
• /
• pp.355-356
• /
• 2008

The light extraction efficiencies of GaN-based light-emitting diodes (LEDs) grown on differently patterned sapphire substrates were investigated by using the ray tracing method. It was found that angle of the pattern surface against the sapphire surface, the number of pattern per unit area were important structural factors for high extraction efficiency.

• 한국분무공학회지
• /
• 제13권3호
• /
• pp.117-125
• /
• 2008

The correlations for the prediction of maximum liquid-phase penetration in diesel spray are reviewed in this study. The existing models developed for the prediction of maximum liquid-phase penetration can be categorized as the zero-dimensional (empirical) model, the multi-dimensional model and the other model. The existing zero-dimensional model can be classified into four groups and the existing multidimensional models can be classified into three groups. The other model includes holistic hydraulic and spray model. The maximum liquid-phase penetration is mainly affected by nozzle diameter, fuel volatility, injection pressure, ambient gas pressure, ambient gas density and fuel temperature. In the case of empirical correlations incorporated with spray angle, the predicted results will be different according to the selection of correlation for spray angle. The research for the effect of boiling point temperatures on maximum liquid-phase penetration is required. In the case of multidimensional model, there exist problems of the grid and spray sub-models dependency effects.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.940-944
• /
• 2003

With the increasing demand for plastic micro components, micro-/nano-molding using the mother stamper has received much attention. If the replication temperature is too high, the adhesion between the stamper and the polymer melt may deteriorate the surface quality of the replicated part, excessively wearing down the stamper. In this paper, an experimental method analyzes the temperature dependency of the anti-adhesion property between the actual stamper with patterns of sub-micrometer and the polymer melt. As a practical example, a correlation between the contact angle of the stamper and the surface quality of the molded substrates as a function of the replication temperature, respectively, was obtained quantitatively.

• 한국기계가공학회지
• /
• 제20권5호
• /
• pp.61-68
• /
• 2021

Movable weirs with multi-stage control are necessary in many Korean rivers to actively control the water storage level. A mesh dependency test was performed to determine the appropriate number of meshes for structural analysis of movable weirs. The standing angles of movable weirs were set to 60°, 45°, 30°, and 15° for stress analysis. The standing angle of 0° was excluded from the analysis because it was unloaded. Changes in the standing angle led to changes in the water depth, maximum pressure, maximum strain, and maximum stress. The maximum average stress and the structural safety of the multi-stage control movable weir were computed and tested using the Ansys FEA software package.

• 한국항공우주학회지
• /
• 제46권6호
• /
• pp.445-451
• /
• 2018

본 논문에서는 현재 한국항공우주학회 공기역학부문위원회에서 주관하고 있는 EFD-CFD 비교 워크숍의 여러 과제 중 CASE 4 삼각날개(Delta Wing)의 천음속영역의 유동해석 결과를 작성하였다. 풍동실험은 추후에 진행될 예정이며, -5~20도 받음각 영역에서의 CFD 해석을 수행하였다. 해석을 수행한 마하수는 0.7, 0.85, 1.2이다. 삼각날개의 적합한 해석조건을 찾기 위해서 기준격자 크기를 조절하여 격자의존성 해석을 수행하였고, 선택한 격자로 받음각 변화에 따라 양력계수와 항력계수의 경향을 파악하였다.

• 한국연소학회지
• /
• 제19권4호
• /
• pp.1-7
• /
• 2014

An experimental study on downwardly spreading flame over slanted electrical wire, which is insulated by Polyethylene (PE), was conducted with applied AC electric fields. The result showed that the flame spread rate decreased initially with increase in inclination angle of wire and then became nearly constant. The flame shape was modified significantly with applied AC electric field due to the effect of ionic wind. Such a variation in flame spread rate could be explained by a thermal balance mechanism, depending on flame shape and slanted direction of flame. Extinction of the spreading flame was not related to angle of inclination, and was described well by a functional dependency upon the frequency and voltage at extinction.

• 항공우주기술
• /
• 제2권2호
• /
• pp.1-10
• /
• 2003

비행선은 주익이 없고 미익에 비해 동체 효과가 큰 형상 특성으로 인해 정적으로 불안정한 특성을 지닌다. 따라서 동안정 특성 예측이 매우 중요하다. 본 연구에서는 강제진동 풍동시험을 통한 비행선의 동안정 특성을 확보하였다. 풍동시험은 미국 BAR사의 독일소재 시설인 BAR LAMP 시설을 사용하였으며, 16회의 정적시험과 26회의 강제진동시험을 수행하였다. 시험결과, 비행선의 동안정 특성은 받음각 뿐만 아니라 옆미끄럼각, 각속도 크기와 방향에 비선형적으로 변한다. 전반적으로 세 방향의 모멘트는 댐핑이 있는 것으로 나타났으며, 수직력과 측력, 교차성분은 불안정하게 나타났다. 조종면의 영향은 작은 것으로 나타났으나 옆미끄럼각의 영향은 완전히 비선형적으로 나타났다.

• Transactions on Electrical and Electronic Materials
• /
• 제12권5호
• /
• pp.189-192
• /
• 2011

A flexible back-light unit (FBLU) is fabricated by embedding plasma discharge clusters in a flexible polymer matrix. The brightness uniformity of an FBLU was measured for various combinations of optical sheets and compared with the simulated results for various bending angles. A gap between light sources causes distinctive integrated brightness curves which have two inflection points depending on bending angle. The brightness distribution of a simulated BLU was in good agreement with that of an actual plasma BLU except for a dark area that appeared at the center of the simulated BLU. The real and simulated BLUs both clearly showed an angle dependency caused by mirror images located between point light sources. On the basis of these results, it is suggested that these mirror-like images could be a major factor in determining the characteristics of FBLUs.

• 천문학회보
• /
• 제43권1호
• /
• pp.51.2-51.2
• /
• 2018

Polarimetry is a powerful technique to investigate the physical properties of surface materials on airless bodies in the solar system. It is known that the degree of linear polarization changes as a function of the phase angle (the angle between Sun-target-Observer). Especially, the dependency of the polarization degree at large phase angle allows us to obtain information related to the particle size and porosity, which is difficult to be determined via other observation techniques (i.e., photometry and spectroscopy). However, despite the advantage, only a few asteroids were observed with polarimetric devices at large phase angles. Here, we present our new polarimetric research of Near-Earth Asteroids (NEAs) observed at the large phase angles. Among the NEAs, we focus on S- and Q-type asteroids, which include: (331471) 1984 QY1, (90075) 2002 VU94, and (66391) 1999 KW4. The observation was conducted using the Pirka 1.6-m Telescope at the Nayoro Observatory of Hokkaido University at the phase angles ${\alpha}{\sim}100degree$, which provides us the maximum polarization degrees of these objects. Considering the observational results together with two objects ((1566) Icarus and (4179) Toutatis) in reference papers [1], [2], we will discuss the implication of the regolith size on their surfaces.