• 한국안전학회지
• /
• 제23권6호
• /
• pp.131-137
• /
• 2008

SCP(Sand Compaction Pile) method that forms a composite ground by driving compacted sand piles into the soft ground. This method is one of the soil improvement techniques for reinforcing and strengthening soft ground deposits. This thesis describes the investigation on the behavior of soft ground reinforced with SCP by low improvement ratio. Direct shear test and consolidation test carried out to verified behavior of composite ground reinforced with SCP. Test results were discussed with reference to the amount of consolidation settlement, variation of shear resistance with area replacement ratio and effect of the stress concentration. And, laboratory model loading test carried out to verified the effect of the location and failure mode of reinforced embankment. Residual shear strength varies with the area replacement and constrict load in the low replacement ratio. Calculated stress concentration ratio overestimate than proposed valve by experimental, theoretical and analytical method. As regards the location, improving right below of the top of the slope was more effective than below of the toe of the slope. This thesis carried out to obtain fundamental information of behavior of the composit ground. Hereafter, centrifuge test that reproduce stress state of the in-situ must be necessary through the further study about pile penetration, reinforce position and construct time.

• 한국광학회지
• /
• 제9권2호
• /
• pp.86-91
• /
• 1998

소오다 석회유리를 기판으로 하고 전기장에 의한 $Cs^+-Na^+$ 이온교환으로 다중 모우드 평면 광도파로를 제작하였다. 광도파로의 각 모우드들에 대한 실효굴절률을 측정하였으며 변형 Fermi 함수 모양으로 맞춤한 굴절률 분포형태를 전자 현미분석기로 얻은 농도분포형태와 비교분석하여 설명하였다. 정량적인 분석결과 약 90%의 $Na^+$이온이 $Cs^+$이온으로 치환되었다. 주어진 인가전기장, 확산온도 및 확산시간으로부터 광도파로 깊이, 이동도 및 굴절률 변화를 구하는 식을 세웠다. 이 식에서 성립하는 광도파로의 깊이와 확산시간의 제곱근 사이의 선형관계 및 광도파로의 깊이와 인가전기장 사이의 선형관계를 실험으로 확인하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.432-435
• /
• 2005

Extensive width reduction of slabs is an important technology to achieve continuous production between the steelmaking and hot rolling processes. Conventionally, a vertical roll process has been used to achieve extensive width reduction. However, it is impossible to avoid the defects such as dog-bone, fish tail and camber. The deformation behavior in the width sizing process is more favorable than that in conventional vertical rolling edger, i.e. the material better flows toward the center of slab. This study is carried out to investigate the deformation of slab by two-step sizing press. The FE-simulation is utilized to predict plastic deformation mode in compression by a sizing press of slabs far hot rolling. In this paper, the various causes of the asymmetrical rolling phenomena are mentioned for the purpose of understanding of rolling conditions. Analytical results of slab-deformation by sizing press are presented below in this study.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.812-817
• /
• 2005

The objective of the present work is to develop a time-domain numerical method of broadband noise in a cascade of airfoils. This paper focuses on dipole broadband noise sources, resulting from the interaction of turbulent inflows with the flat-plate airfoil cascade. The turbulence response of a two-dimensional cascade is studied by solving both of the linearised and full nonlinear Euler equations employing accurate higher order spatial differencing, time stepping techniques and non-reflecting inflow/outflow boundary condition. The time-domain result using the linearised Euler equations shows good agreement with the analytical solution using the modified LINSUB code. Through the comparison of the nonlinear time-domain result using the full nonlinear Euler equations with the linear, it is found that the acoustic mode amplitude of the nonlinear response is less than that of the linear response due to the energy cascade from low frequency components to the high frequency ones. Considering the merits of the time-domain methods over the typical time-linearised frequency-domain analysis, the current method is expected to be promising tools for analyzing the effects of the airfoil shapes, non-uniform background flow, linear-nonliear regimes on the broadband noise due to gust-cascade interaction.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.928-933
• /
• 2004

The vibration characteristic is a primary design factor. The cylindrical shells are used as a primary components of complex structure. also, The cylindrical shells have oblique angle. In this study, The vibrational characteristics of steel and plain wave GFRP cylindrical shell with an oblique end are given by experimental and finite element method. To be find characteristic of the oblique end, the mass of the cylindrical shell is maintained. Natural frequency and mode shapes of isotropic and plain weave composite shells are obtained by modal test. The results are compared with those of the finite element method. The simply supported boundary conditions with bolts along the circumferential direction of the GFRP shell are well achieved. Also, The clamped boundary conditions is applied to the steel specimen. Those are shown to agree well with the analytical results and finite element analysis results.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제12권5호
• /
• pp.2009-2028
• /
• 2018

Considering a dual-hop energy-harvesting (EH) relaying system, this paper advocates novel relaying protocols based on adaptive time power switching-based relaying (AR) architecture for amplify-and-forward (AF) mode. We introduce novel system model relaying network with impacts of co-channel interference (CCI) and derive analytical expressions for the average harvested energy, outage probability, and the optimal throughput of the information transmission link, taking into account the effect of CCI from neighbor cellular users. In particular, we consider such neighbor users procedure CCI both on the relay and destination nodes. Theoretical results show that, in comparison with the conventional solutions, the proposed model can achieve optimal throughput efficiency for sufficiently small threshold SNR with condition of reasonable controlling time switching fractions and power splitting fractions in concerned AR protocol. We also explore impacts of transmission distances in each hop, transmission rate, the other key parameters of AR to throughput performance for different channel models. Simulation results are presented to corroborate the proposed methodology.

• Preventive Nutrition and Food Science
• /
• 제3권2호
• /
• pp.111-118
• /
• 1998

To develop a simple, rapid and simultaneous analytical method of phenolic compounds using gas chromatography (GC) and gas chromatography/mass spectrophometer (GC/Ms), this experiment was carried out to search the retention times of capillary columns and the characteristics of fragment ions in electron impact mass spectra. Most of trimethylsilyl derivatives and underivatized phenolic compounds were separated very well on three kinds of capillary columns(HP-1), Ultra-2 and HP-35). Quantitiative determination of phenolic compounds was achieved by internal standards (p-hydroxybenzoic acid iopropyl ester, p-hydroxybenzoic acid ethyl ester). Calibration plts were linear in the investigated range, and the limits of detection were about 5 ng at split mode method. When analyzed by three columns, theseparation times were fairly constant on two nonpolar columns, but a few compounds showed slightly different separation order by the itnermediate polar HP-35 column. The important characteristic patterns of TMS derivatives of phenolic compounds on the EI/MS spectrra appeared at the base peak of [M-15]+ ion and presented at high abundance in most TMS derivatives of phenoloc compounds. [M]+, [M-CH3-COO]+, [M-Si(CH3)4]+ and [M-Si(CH3)4 -CH3]+ also observed in mass spectra of these compounds . Although several compounds have the same retention times on GC column, it might be possible to identify these compounds by the different patternsof mass frgement ions. The TMS derivatives, thus , provide additional information for identification of phenolic compounds in biological systems.

• Steel and Composite Structures
• /
• 제35권2호
• /
• pp.249-260
• /
• 2020

The main purpose of this research work is to investigate the free vibration of conical shell structures reinforced by graphene platelets (GPLs) and the elastic properties of the nanocomposite are obtained by employing Halpin-Tsai micromechanics model. To this end, a shell model is developed based on Donnell's theory. To solve the problem, the analytical Galerkin method is employed together with beam mode shapes as weighting functions. Due to importance of boundary conditions upon mechanical behavior of nanostructures, the analysis is carried out for different boundary conditions. The effects of boundary conditions, semi vertex angle, porosity distribution and graphene platelets on the response of conical shell structures are explored. The correctness of the obtained results is checked via comparing with existing data in the literature and good agreement is eventuated. The effectiveness and the accuracy of the present approach have been demonstrated and it is shown that the Donnell's shell theory is efficient, robust and accurate in terms of nanocomposite problems.

• Journal of Power Electronics
• /
• 제19권6호
• /
• pp.1554-1565
• /
• 2019

When grid voltage is unbalanced, the grid-connected output current and power of Virtual Synchronous Generators (VSGs) are distorted and quadratic. In order to improve the power quality of a grid connected to a VSG when the grid voltage is unbalanced, a comprehensive coordinated control strategy is proposed. The strategy uses the positive sequence current reference command obtained by a VSG in the balanced current control mode to establish a unified negative sequence current reference command analytical expression for the three objectives of current balance, active power constant and reactive power constant. In addition, based on the relative value of each target's volatility, a comprehensive wave function expression is established. By deriving the comprehensive wave function, the corresponding negative sequence current reference value is obtained. Therefore, the VSG can achieve the minimum comprehensive fluctuation under the premise that the three targets meet the requirements of grid connection, and the output power quality is improved. The effectiveness of the proposed control strategy is verified by simulation and experimental results.

• Smart Structures and Systems
• /
• 제2권2호
• /
• pp.189-208
• /
• 2006

Monitoring large-scale civil engineering structures such as offshore platforms and high-large buildings requires a large number of sensors of different types. Innovative sensor data information technologies are very extremely important for data transmission, storage and retrieval of large volume sensor data generated from large sensor networks. How to obtain the optimal sensor set and placement is more and more concerned by researchers in vibration-based SHM. In this paper, a method of determining the sensor location which aims to extract the dynamic parameter effectively is presented. The method selects the number and place of sensor being installed on or in structure by through the tolerance domain statistical inference algorithm combined with second order sensitivity technology. The method proposal first finds and determines the sub-set sensors from the theoretic measure point derived from analytical model by the statistical tolerance domain procedure under the principle of modal effective independence. The second step is to judge whether the sorted out measured point set has sensitive to the dynamic change of structure by utilizing second order characteristic value sensitivity analysis. A 76-high-building benchmark mode and an offshore platform structure sensor optimal selection are demonstrated and result shows that the method is available and feasible.