• Journal of Appropriate Technology
• /
• v.6 no.2
• /
• pp.174-182
• /
• 2020

The permissible limit of ammonia concentration in drinking water recommended by the World Health Organization (WHO) is 1.5 mg/L. However, in the case of groundwater in Kathmandu, Nepal, the concentration of ammonia fluctuates dramatically from 0 to 120 mg/L at different locations and groundwater depths (Chapagain et al., 2010). Such a high concentration of ammonia causes aesthetic problems in drinking water, such as bad taste and odor; hence, prior treatment is required. In Kathmandu, half of the population utilizes groundwater, which is also employed for drinking water, but owing to a lack of knowledge of household water filters, residents of Kathmandu tend to depend greatly on commercially available jar water than on the installation of a proper household filtration method. Thus, in our study, we employed adsorption and reverse osmosis (RO) as two of the most viable decentralized/household treatment options to address the issue of high contamination of ammonia in drinking water. We evaluated their performances from technical and the economic perspectives using synthetically prepared groundwater at varying ammonia concentrations (50 mg/L and 15 mg/L). Consequently, it was found that adsorption via ion exchange (IE) resin was a comparatively better ammonia removal technology than RO, with 100% ammonia removal even after regeneration; the removal by RO was limited to up to 90%. Furthermore, our study suggests that IE is the most suitable ammonia removal technology for places with lower water consumption (< 50 L/day), whereas RO seemed to be a cost-effective technology for places with higher water consumption, where the daily water demand exceeds 50 L/day. Lastly, these assessments suggest that installing a suitable household treatment system would be more efficient and sustainable from both technical and economic points of view than purchasing commercially bottled water.

• Journal of Korean Home Economics Education Association
• /
• v.32 no.4
• /
• pp.149-170
• /
• 2020

The purpose of this study was to develop and evaluate a Smart learning-based middle school home economics education plan to improve the online home economics education classes. The educational plan in this study was completed through the process of analysis, design, development, and evaluation. The results of this study are as follows. First, as a result of analyzing consumer life units in the middle school textbooks based on 2015-revised curriculum, Smart learning activities were presented in only two out of the 12 textbooks analyxed. Second, a Smart learning-based middle school home economics education plan was developed in this study with the following characteristics: the topics and contents are structured so that to help learners actively engage in the teaching and learning activities; the education plan to reflects various media and current issues that learners may be interested in; the lesson plans were structured with the premise of online classes; softwares that enable real-time discussion and collaboration are used; and the evaluation method are composed of online activities. Third, the expert evaluation scores for the educational plan and activity materials developed were 4.52 (5-point Likert scale), when averaged across subject, goal, content, teaching/learning activity, and evaluation, and the overall content validity index(CVI) was 0.95. The adequacy of execution, benefit, attractiveness, usefulness, and feasibility were highly with an average of 4.62. Based on the experts' comments, the education plan and activity materials were revised and completed. This study is meaningful in that it developed teaching and learning activities based on online classes after the COVID-19 outbreak, overcoming the limitations of offline classes. It has implications for face-to-face home economics classes due to COVID-19, as it suggests ways to blend online and offline teaching/learning activities depending on the situation.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.1
• /
• pp.1-9
• /
• 2022

The effect of sediments in a waste dumping area on marine organisms was evaluated using sediment toxicity tests with a benthic amphipod (Monocorophium acherusicum) and bioluminescent bacterium (Vibrio fischeri) in accordance with the Korean Standard Method for Marine Wastes (KSMMW). Nine sites in the East Sea-Byeong, East Sea-Jeong, and Yellow Sea-Byeong areas were sampled from 2016 to 2019. The test results showed that the relative average survival rate (benthic amphipods) and relative luminescence inhibition rate (luminescent bacteria) were below 30%, which were judged to be "non-toxic." However, in the t-test, a total of 12 benthic amphipod samples (6, 1, 1, and 4 in 2016, 2017, 2018, and 2019, respectively) were significantly different (p<0.05) from the control samples. To identify the source of toxicity on benthic amphipods, a simple linear regression analysis was performed between the levels of eight heavy metals (Cr, As, Ni, Cd, Cu, Pb, Zn, and Hg) in sediments and the relative average survival rate. The results indicated that Cr had the highest contribution to the toxicity of benthic amphipods (p = 0.000, R2 = 0.355). In addition, Cr was detected at the highest concentration at the DB-85 station and exceeded the Marine Environment Standards every year. Although the sediments were determined as "not toxic" according to the ecotoxicity criteria of the KSMMW, the results of the statistical significance tests and toxicity identification evaluation indicated that the toxic effect was not acceptable. Therefore, revising the criteria for determining the toxic effect by deriving a reference value through quantitative risk assessment using species sensitivity distribution curves is necessary in the future.

• Journal of the Korean Society of Radiology
• /
• v.16 no.1
• /
• pp.35-43
• /
• 2022

In this study, a survey was conducted and analyzed to find out the satisfaction of online classes among students enrolled in the radiology department of a university located in Busan city. As a result, in terms of satisfaction with online classes, male scores were higher, but there was no statistically significant difference. In the interdisciplinary system, the satisfaction score of the students enrolled in Bachelor's degree was high, and there was a statistically significant difference except for the satisfaction of learning participation (p<0.001, p<0.05). For class satisfaction by grade level, Senior had higher scores, and there were statistically significant differences except for learning participation satisfaction (p<0.001, p<0.01, p<0.05). In the satisfaction survey according to the number of lectures, the scores of the students who took 4-7 lectures were found to be high except for the satisfaction of learning participation, and there was a statistically significant difference (p<0.01, p<0.05). In the method of communication with the instructor, students who used e-mail showed high scores, and there was a statistically significant difference in lecture satisfaction (p<0.05). In the correlation analysis between sub-variables for online classes, statistically significant correlations were established in all areas. Most of the students preferred class methods such as recorded classes and classes using external content such as YouTube, and when asked about the merits of online classes, many students answered that the advantages of online classes were repetitive classes and no restrictions on time and place. When asked about the shortcomings of online classes, many students answered that it was a lack of concentration and lack of communication with the instructor. This study was conducted to provide basic data to improve the satisfaction of online classes that will increase in the future. Therefore, based on the results of this study, it is expected that more quality online classes will be produced so that students' satisfaction with online classes can be improved.

• Journal of Food Hygiene and Safety
• /
• v.37 no.3
• /
• pp.149-158
• /
• 2022

This study aimed to investigate pesticide residues in 160 stalk and stem vegetables marketed in Northern Gyeonggi-do. The QuEChERS method using GC-MS/MS and LC-MS/MS was employed to analyze the residues of 341 pesticides in the samples. The maximum or lower than the residue limit was recorded in 75 samples (46.9%), while 4 samples (2.5%) exceeded the maximum residue limit (MRL). Thirty-nine kinds of residual pesticides were detected including fungicides (14), insecticides (22), herbicides (2), and plant growth regulator (1). Carbendazim and pendimethalin were the most frequelntly detected pesticides. Fenitrothion, procymidone, and diazinon exceeded MRL in garlic chives, and Welsh onion. This indicated that these vegetables along with water celery should be constantly monitored.

• Journal of the Korean Geotechnical Society
• /
• v.38 no.7
• /
• pp.49-62
• /
• 2022

The hollow modular concrete block reinforced foundation method is one of the ground reinforcement foundation methods that uses hexagonal honeycomb-shaped concrete blocks with mixed crushed rock to reinforce soft grounds. It then forms an artificial layered ground that increases bearing capacity and reduces settlement. The hollow modular honeycomb-shaped concrete block is a geometrically economical, stable structure that distributes forces in a balanced way. However, the behavioral characteristics of hollow modular concrete block reinforced foundations are not yet fully understood. In this study, a bearing capacity test is performed to analyze the reinforcement effectiveness of the hollow modular concrete block through the laboratory model tests. From the load-settlement curve, punching shear failure occurs under the unfilled sand condition (A-1-N). However, the filled sand condition (A-1-F) shows a linear curve without yielding, confirming the reinforcement effect is three times higher than that of unreinforced ground. The bearing capacity equation is proposed for the parts that have contact pressure under concrete, vertical stress of hollow blocks, and the inner skin friction force from horizontal stress by confining effect based on the schematic diagram of confining effect inside a hollow modular concrete block. As a result of calculating the bearing capacity, the percentage of load distribution for contact force on the area of concrete is about 65%, vertical force on the area of hollow is 16.5% and inner skin friction force of area of the inner wall is about 18.5%. When the surcharge load is applied to the concrete part, the vertical stress occurs on the area of the hollow part by confining effect first. Then, in the filled sand in the hollow where the horizontal direction is constrained, the inner skin friction force occurs by the horizontal stress on the inner wall of the hollow modular concrete block. The inner skin friction force suppresses the punching of the concrete part and reduces contact pressure.

• Journal of Intelligence and Information Systems
• /
• v.28 no.2
• /
• pp.147-170
• /
• 2022

Although the number of patent which is one of the core outputs of technological innovation continues to increase, the number of low-value patents also hugely increased. Therefore, efficient evaluation of patents has become important. Estimation of patent lifespan which represents private value of a patent, has been studied for a long time, but in most cases it relied on a linear model. Even if machine learning methods were used, interpretation or explanation of the relationship between explanatory variables and patent lifespan was insufficient. In this study, patent lifespan (number of renewals) is predicted based on the idea that patent lifespan represents the value of the patent. For the research, 4,033,414 patents applied between 1996 and 2017 and finally granted were collected from USPTO (US Patent and Trademark Office). To predict the patent lifespan, we use variables that can reflect the characteristics of the patent, the patent owner's characteristics, and the inventor's characteristics. We build four different models (Ridge Regression, Random Forest, Feed Forward Neural Network, Gradient Boosting Models) and perform hyperparameter tuning through 5-fold Cross Validation. Then, the performance of the generated models are evaluated, and the relative importance of predictors is also presented. In addition, based on the Gradient Boosting Model which have excellent performance, Accumulated Local Effects Plot is presented to visualize the relationship between predictors and patent lifespan. Finally, we apply Kernal SHAP (SHapley Additive exPlanations) to present the evaluation reason of individual patents, and discuss applicability to the patent evaluation system. This study has academic significance in that it cumulatively contributes to the existing patent life estimation research and supplements the limitations of existing patent life estimation studies based on linearity. It is academically meaningful that this study contributes cumulatively to the existing studies which estimate patent lifespan, and that it supplements the limitations of linear models. Also, it is practically meaningful to suggest a method for deriving the evaluation basis for individual patent value and examine the applicability to patent evaluation systems.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.50 no.1
• /
• pp.53-67
• /
• 2022

This study started from recognizing the need to study place identity from the perspective of residents experiencing the place in daily life. The subject area of the study, Shin-Cheorwon, Galmal-eup, Cheorwon-gun, Gangwon-do area, had a low population until the division of Korea in 1945. Since then, the residents have created the milieu under Shin-Cheorwon's regional historic and cultural context. Thus, the study on this area can show the formation of the interrelationship of the region and residents. The purpose of this study is to understand the meaning and identity of the everyday places of Shin-Cheorwon. Photovoice was chosen as the method for successful Participatory Research; Participant's active intervention stage, 'Documentation (4th step)', Narration (5th step), researcher's analysis stage 'Ideation (6th step)' were specifically used. As a result, the following characteristic of the places chosen by participants could be found: the meaning and relationship with the residents, similarities, and differences in people shown based on their age, length of residence, etc. Through this, participants recollected the past places, found the meaning of the place of the present, and deduced the placeness that Shin-Cheorwon should have in the future. The study identified the place identity that holds the perspective of the residents in their daily life and provides implications on the follow-up studies of place identity. In addition, it is expected that it will apply to urban planning and spatial design in further studies of how residents perceive the space formed by urban development using photovoice methodology.

• Journal of Korea Entertainment Industry Association
• /
• v.15 no.8
• /
• pp.91-106
• /
• 2021

The purpose of this study is to define the process of leading to self-realization and social solidarity through the process of contents planning, production, and distribution as Contents Activism, and to categorize specific execution steps. Based on this, we try to analyze concrete cases to find out the social meaning and effect of the practice of Contents Activism. As for the research method, after examining the differences between traditional activism and Contents Activism through a review of previous studies, the implementation process of Contents Activism was categorized into 7 steps. By applying this model, this study analyzed two cases of Contents Activism. The first case is the 100 laps challenge in the backyard planned by an elderly man ahead of his 100th birthday in early 2020, when the fear of COVID-19 spread. Sir Tom Moore, who lives in the UK, challenged to walk 100 laps in the backyard to help medical staff from the National Health Service as COVID-19 infections and deaths increased due to a lack of protective equipment. His challenge, which is difficult to walk without assistive devices due to cancer surgery and fall aftereffects, drew sympathy and participation from many people, leading to global solidarity. The second case analyzes the case of 'The Unfreedom of Expression, Afterwards' by Kim Seo-kyung and Kim Woon-seong, who were invited to the 2019 Aichi Triennale special exhibition in Japan. The 'Unfreedom of Expression, After' exhibition was a project to display the Statue of Peace and the lives of comfort women in the Japanese military, but it was withdrawn after three days of war due to threats and attacks from the far-right forces. Overseas artists who heard this news resisted the Triennale's decision, took and shared photos in the same pose as the Statue of Peace on social media such as Twitter and Instagram, empathizing with the historical significance of the Statue of Peace. Activism, which began with artists, has expanded through social media to the homes, workplaces, and streets of ordinary citizens living in various regions. The two cases can be said to be Contents Activism that led to social practice while solidifying and communicating with someone through contents.

• Korean Journal of Heritage: History & Science
• /
• v.55 no.3
• /
• pp.46-58
• /
• 2022

This study analyzed the documentation trend of garden components such as plants, infrastructure, unit facilities, and structures, based on 188 measurement drawings of 94 old houses in a report on the documentation of the national folklore cultural heritage. The findings are as follows. First, it was found that plants and structures continuously appeared as the subject of measurement drawings, while infrastructure was often omitted. It was confirmed that unit facilities, which are smaller than other components, were frequently excluded from the documentation subject as well due to frequent changes such as movement, loss, and expansion. Second, the level of expression in measurement drawings showed different aspects for each component. The unit facilities showed a large change over time with respect to the level of documentation, and the level of documentation was somewhat polarized, particularly toward the latter stage. This suggests that the level of documenting the drawings limited to specific facilities improved, but the overall level of drawings did not improve, such as a lack of diversification of expression techniques suitable for various unit facilities. On the other hand, it was confirmed that the level of documenting the drawings for plants, infrastructure and structures did not change to a significant degree, implying that no improvements were made to the expression of components. Third, as for the technique of detailed expression, in the case of plants, vegetation status was prepared without distinction of old or protected trees that have historical value. Above all, there was no record of the vegetation structure that could help grasp the vegetation landscape of the outer area. As for the infrastructure, there was no consistent expression technique to systematically convey topographic changes such as the height and slope of the land. In addition, since there was no subtype classification defined for unit facilities and structures, there was no subject or method of documentation. This study is meaningful in that it expanded the category of documentation, which has been concentrated on buildings in old houses, to gardens, and called attention to the need for documenting the gardens for the preservation and management of old houses as an integration of the building and outer area.