• Journal of Sensor Science and Technology
• /
• v.26 no.3
• /
• pp.155-159
• /
• 2017

The analog-to-digital converter (ADC) is an important component in various fields of sensor signal processing. This paper presents an expandable flash analog-to-digital converter (E-flash ADC) for sensor signal processing using a comparator, a subtractor, and a multiplexer (MUX). The E-flash ADC was simulated and designed in $0.35-{\mu}m$ standard complementary metal-oxide semiconductor (CMOS) technology. For operating the E-flash ADC, input voltage is supplied to the inputs of the comparator and subtractor. When the input voltage is lower than the reference voltage, it is outputted through the MUX in its original form. When it is higher than the reference voltage, the reference voltage is subtracted from the input value and the resulting voltage is outputted through the MUX. Operation of the MUX is determined by the output of the comparator. Further, the output of the comparator is a digital code. The E-flash ADC can be expanded easily.

• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.197-200
• /
• 2002

In this paper, presents a 1.8V 8-bit 300MSPS CMOS Subranging Analog to Digital Converter (ADC) with a novel reference multiplex is described. The proposed hか converter is composed of Sub A/D Converter block, MUX (Multiplexer) block and digital block. In order to obtain a high-speed operation, further, a novel dynamic latch, an encoder of novel algorithm and a MUX block are proposed. As a result, this A/D Converter is operated 100MHz input frequence by 300MHz sampling rate.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.7 no.2
• /
• pp.7-12
• /
• 2013

In this paper, we propose a brushless DC motor drive system for active knee prosthesis and low-cost estimation method for phase current from DC-link current. To control motor torque directly, current sensing is very important and current sensing point should be synchronized with voltage switching command to minimize the effect of switching noise in current measurement, For maintaining small form factor, simplifying control schemes and achieving low-cost system, control schemes using DC-link current are used. Moreover, we incorporated phase current estimation method using analog MUX for minimizing current estimation error between DC-link current and phase current. The validity of the proposed system is verified through experimental works.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.1
• /
• pp.175-184
• /
• 2016

In this paper, we propose the method to measure the capacitances using not LCR meter but capacitance to voltage(C/V) conversion. And we design the analog MUX circuits that convert 192 channels to 6 MUX channels in order to implement the diagnosis of multi-channel ultrasonic probe. This paper derives the conversion function that converts the digital voltage of each MUX channel to the capacitance using the least squares method because the circuit characteristics that convert the voltage of each MUX channel to the capacitance are different. The developed prototype illustrates the performance test results that the measure times are measured by within 4sec and the measure error rates of maximum, minimum, and average values are within 5% in terms of the repeated measurements of all 192 channels.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.11 no.4
• /
• pp.63-69
• /
• 2012

This paper describes novel scheme of a gray scale capacitive fingerprint image for high-accuracy capacitive sensor chip. The typical gray scale image scheme used a DAC of big size layout or charge-pump circuit of non-volatile memory with high power consumption and complexity by a global clock signal. A modified capacitive detection circuit of charge sharing scheme is proposed, which uses DLC(down literal circuit) based on a neuron MOS(vMOS) and analog simple multiplexor. The detection circuit is designed and simulated in 3.3V, $0.35{\mu}m$ standard CMOS process. Because the proposed circuit does not need a comparator and peripheral circuits, a pixel layout size can be reduced and the image resolution can be improved.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.4A
• /
• pp.439-446
• /
• 2004

This paper describes high speed and low power design techniques for an 8-bit 500MSamples/s CMOS 2-step ADC. Instead of the conventional closed-loop architecture, the newly proposed ADC adopts open-loop architecture and uses a reset-switch to reduce loading time in an environment of big parasitic-capacitances of mux-array. An analog-latch is also used to reduce power consumption. Simulation result shows that the ADC has the SNDR of 46.91㏈ with a input frequency of 103MHz at 500Msample/s and consumes 203㎽ with a 1.8V single power supply. The chip is designed with a 0.18mm 1-poly 6-metal CMOS technology and occupies active area of 760${\mu}{\textrm}{m}$*800${\mu}{\textrm}{m}$.

• Proceedings of the Korean Society of Medical Physics Conference
• /
• 2002.09a
• /
• pp.468-470
• /
• 2002

We have designed X-ray detection system and multi-channel data acquisition system for Spiral CT application. X-ray detection system consists of scintillator and photodiode. Scintillator converts X-ray into visible light. Photodiode converts visible light into electrical signal. The multi-channel data acquisition system consists of analog, digital, master and backplane board. Analog board detects electrical signal and amplifies signal by 140dB. Digital board consists of MUX(Multiplex) which routes multi-channel analog signal to preamplifier, and ADC(Analog to Digital Converter) which converts analog signal into digital signal. Master board supplies the synchronized clock and transmits the digital data to image reconstructor. Backplane provides electrical power, analog output and clock signal. The system converts the projected X-ray signal over the detector array with large gain, samples the data in each channel sequentially, and the sampled data are transmitted to host computer in a given time frame. To meet the timing limitation, this system is very flexible since it is implemented by FPGA(Field Programmable Gate Array). This system must have a high-speed operation with low noise and high SNR(signal to noise ratio), wide dynamic range to get a high resolution image.

• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.951-954
• /
• 2003

본 논문에서는 고속. 저전력에 적합한 개방 구조를 갖는 8-비트 500Msmaples/s 2-Step ADC 를 제안하였다. 500Msmaples/s 의 고속 동작을 위해서 기존의 M-DAC을 이용한 폐쇄 구조 대신 개방형 구조를 사용하였다. 이와 더불어 저전력을 구현하기 위해서 analog-latch 를 제안하여 동적 동작을 수행시킴으로써 전력 소모를 줄였으며 , mux 의 구현 시 reset switch를 이용하여 로딩 시간을 개선함으로써 high-speed 에 적합하도록 설계하였다. 제안된 ADC 는 1-poly 6-metal 0.18um CMOS 공정을 이용하였으며 1.8V 전원 전압을 이용하여 250mW 의 전력을 소모하며 500M 샘플링 주파수에서 120MHz 신호 입력 시 7.6 비트의 ENOB를 얻을 수 있었다.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.10
• /
• pp.148-158
• /
• 2012

This paper presents the design of the incremental delta-sigma ADC. The proposed circuit consists of pre-amplifier, S & H circuit, MUX, delta-sigma modulator, and decimation filter. Third-order discrete-time delta-sigma modulator with 1-bit quantization were fabricated by a $0.18{\mu}m$ CMOS technology. The designed circuit show that the modulator achieves 87.8 dB signal-to-noise and distortion ratio (SNDR) over a 5 kHz signal bandwidth and differential nonlinearity (DNL) of ${\pm}0.25$ LSB, integral nonlinearity (INL) of ${\pm}0.2$ LSB. Power consumption of delta-sigma modulator is $941.6{\mu}W$. It was decided that N cycles are 200 clock for 16-bits output.

• Bulletin of the Korean Space Science Society
• /
• 2009.10a
• /
• pp.46.3-46.3
• /
• 2009

The SAR (Synthetic Aperture Radar) satellite has the advantage of implementing the imaging mission even though it is night time, cloudy weather, and all weather conditions, which is different from the satellite with the optical payload. This is the reason why the SAR satellite comes into the spotlight in the observation satellite field. The Korea Aerospace Research Institute (KARI) has been developing the first Korean SAR satellite and is currently integrating and testing the Flight Model. For the launch vehicle service, KARI finalized the selection of the launch vehicle service provider and finished Critical Design Review (CDR) of the interface between the bus and the launch vehicle. KARI and launch vehicle service provider also finished the test of the telemetry interface between the bus and the launch vehicle. The test of the telemetry interface has the purpose of checking the interface of the telemetry which is the SOH(State-of-Health) of the satellite in an early launch stage. For this test, KARI has finished the development of the spacecraft simulator which is composed of the bus simulator to generate the analog telemetry and the launch vehicle simulator to gather the telemetry. In this research, the result of the hardware implementation and the software implementation for the spacecraft simulator were described. Finally the results of the launch vehicle telemetry MUX test which were performed at the launch vehicle provider's design office by using the spacecraft simulator were summarized. It is expected that this simulator will be used in the next test after the manufacture of the launch vehicle.