• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.305-344
• /
• 2008

This paper presents the active control of flexible beam vibration. The beam was excited by a steady-state point force by mini shaker and the control was performed by mini shaker. To perform active control, least-mean-square (LMS) algorithm was used because it can easily obtain the complex transfer function in real-time. So an adaptive controller based on Filtered-X LMS algorithm was used and the controller was defined by minimizing the square of the response at a location of error sensor. In order to fine out performance tendency, input amplitude was changed in several cases and active vibration control was performed.

• Proceedings of the KIEE Conference
• /
• 1999.11c
• /
• pp.643-645
• /
• 1999

In experiment, a real inverted pendulum system has state constraints and limited amplitude of input. These problems make it difficult to design a swing-up controller. To overcome these problems, we design a sliding mode controller considering physical behaviour of the inverted pendulum system. This sliding mode controller uses a switching control action to converge along a specified path derived from energy equation from a state around the path to desired states(standing position). And optimal control method is used to guarantee stability at unstable equilibrium position. The designed controller can be applied to all inverted pendulum systems regardless of the values of their parameters. Compared with previous existing controllers, it is simple and easy to tune. Experimental results are given to show the effectiveness of this controller.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.457-462
• /
• 2006

This paper is concerned with the active vibration control experiment on cylindrical shell equipped with Macro Fiber Composite(MFC) actuators. The MFC actuators were glued to the cylindrical shell in circumferential directions. To verify the theoretical result, vibration test using impact hammer and accelerometer was carried out. It was found from experiments that theoretical result predicts experimental result to some extent. The positive position feedback controllers were designed and applied to the test article. It was observed that the resonant amplitude of the fundamental mode was reduced by 20dB thus achieving active vibration control. The active vibration control of the response subject to non resonant excitation has been of interest. We developed the combination of the positive position feedback controller which can cope with the fundamental mode and the positive position feedback controller which can counteract the external disturbance with non resonant frequency. It was found from experiments that the hybrid controller can suppress the vibration amplitude successfully.

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.54-57
• /
• 1998

This paper describes a digital implementation of a pulse amplitude modulation(PAM) method for a unity-power-factor buck-booster converter. A digital controller is designed and implemented by a Digital Signal Processor(DSP) to replace the analog control circuit for PAM. Experimental results are presented and compared with simulations.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.8
• /
• pp.718-722
• /
• 2015

This paper proposes a fractional-order PID (Proportional-Integral-Derivative) control used electromagnetic strip stabilization controller in a continuous galvanizing line. Compared to a conventional PID controller, a fractional-order PID controller has integration-fractional-order and derivation-fractional-order as additional control parameters. Thanks to increased control parameters, more precise controller adjustment is available. In addition, accurate transfer function of a real system generally has a fractional-order form. Therefore, it is more adequate to use a fractional-order PID controller than a conventional PID controller for a real world system. Finite element models of a $1200{\times}2000{\times}0.8mm$ strip, which were extracted using a commercial software ANSYS were used as simulation plants, and Gaussian mixture models were used to find optimized control parameters that can reduce the strip vibrations to the lowest amplitude. Simulation results show that a fractional-order PID controller significantly reduces strip vibration and transient response time than a conventional PID controller.

• Proceedings of the KIEE Conference
• /
• 1991.11a
• /
• pp.137-139
• /
• 1991

This paper proposes a minimum power factor control for maximum efficiency operation of an induction motor, under low load condition. Minimum input or maximum efficiency operation is achived by properly adjusting the amplitude of the stator voltage, with the three phase AC voltage controller. Through the simulation, the relationships between the delay angle and input power under various load conditions are examined. Experimental results are also given, which show good coincidence with the simulation results.

• Journal of The Korean Astronomical Society
• /
• v.29 no.spc1
• /
• pp.387-388
• /
• 1996

The principles to attain improved accuracy in a new controller for large CCD and mosaics detectors with the application of 16- and 32-bit DSP are presented.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 1991.06a
• /
• pp.129-132
• /
• 1991

In this paper, the active noise controll system in duct is analyzed with real time implementation. The primary noise signal detected by microphone is modeled using adaptive algorithm and the secondary signal which has the same amplitude and 180$^{\circ}$phase shift with the primary noise signal is generated in the controller. We used the DSP56001 as a real-time processor and LMS algorithm as a adaptive technique, the experimental results shows that our system can reduce the noise level in duce to 15~40[db].

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.1
• /
• pp.131-136
• /
• 2017

In this study, we design a controller that regulates the water leveling system which suffers from the disturbance. A number of control techniques have been reported which can reduce the amplitude of disturbance. But due to input-delay, these methods do not perform as expected. To overcome the problem, this paper introduces a filter and proposes a proportional and integral (PI) controller that combined with the filter (modifed PI controller). Moreover, we combine the controller with disturbance observer (DOB) that can estimate and eliminate disturbance. The proposed controller and combined the controller with DOB are tested using MATLAB.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.6-8
• /
• 2004

The objective of this paper is to develop a powered wheelchair controller based on EMG for users with high-level spinal cord injury using a proportional control scheme. An advantage of EMG is relative convenience of acquisition by a surface electrode to users. Direction information can be easily extracted from two EMG channels and force information can be acquired by proportional relationship between the amplitude of EMG and user's power, respectively. Pattern classification algorithm is a threshold method with a supervised learning process. Furthermore, the emergency situation can be avoided using an interrupt function. We evaluated the performance of powered wheelchair controller by navigating a pre-defined path with three non-handicapped people. The results show the feasibility of EMG as an input interface for powered wheelchair and other devices for the seriously disabled.