• Journal of Microbiology and Biotechnology
• /
• v.4 no.2
• /
• pp.146-150
• /
• 1994

Production of poly-$\beta$-hydroxybutyrate (PHB) in fed-batch fermentation was studied. Utilization of carbon for PHB biosynthesis was investigated by using feeding solutions with different ratios of carbon to nitrogen (C/N). It was observed that at a high C/N ratio carbon source was more preferably utilized for PHB accumulation while its consumption for cellular metabolism appeared to be more favored at a low C/N value. A high cell concentration (184 g/l) was achieved when ammonium hydroxide solution was fed to control the pH, which was also utilized as the sole nitrogen source. For the mass production of PHB, two-stage fed-batch operations were carried out where PHB accumulation was observed to be stimulated by switching the ammonium feeding mode to the nitrogen limiting condition. A large amount of PHB (108 g/l) was obtained with cellular content of 80% within 50 hrs of operation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.04b
• /
• pp.147-151
• /
• 2000

This paper presents the electrochemical etch-stop characteristics of single-crystal silicon in a tetramethyl ammonium hyciroxide(TMAH):isopropyl alcohol(IPA):pyrazine solution. Addition of pyrazine to a TMAH:IPA etchant increases the etch-rate of (100) silicon, thus the elapsed time for etch-stop was shortened. The current-voltage(I-V) characteristics of n- and p-type silicon in a TMAH:IPA:pyrazine solution were obtained, respectively. Open circuit potential(OCP) and passivation potential(PP) of n- and p-type silicon, respectively, were obtained and applied potential was selected between n- and p-type silicon PP. The electrochemical etch-stop is applied to the fabrication of 801 microdiaphragms having $20\;{\mu}m$ thickness on a 5-inch silicon wafer. The averge thicknesses of 801 microdiaphragms fabricated on the one wafer were $20.03\;{\mu}m$ and standard deviation was ${\pm}0.26{\mu}m$. The silicon surface of the etch-stopped microdiaphragm was extremely flat without noticeable taper or other nonuniformities. The benefits of the electrochemical etch-stop in a TMAH:IPA:pyrazine solution become apparent when reproducibility in the microdiaphragm thickness for mass production is considered. These results indicate that the electrochemical etch-stop in a TMAH:IPA:pyrazine solution provides a powerful and versatile alternative process for fabricating high-yield silicon microdiaphragms.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.193-197
• /
• 2001

This study was carried out to recover gold, silver and other valuable metals from the printed circuit boards (PCB) of waste computers. PCB samples were crushed to under 1mm by a shredder and initially separated into 30% conducting and 70% non-conducting materials by an electrostatic separator. The conducting materials, which contained the valuable metals, were then used as the feed material for magnetic separation where it was found that 42% was magnetic and 58% non- magnetic. The non-magnetic materials contained 0.227mg/g Au and 0.697mg/g Ag. Further leaching of the non-magnetic component using 2.0M sulfuric acid and 0.2M hydrogen peroxide at 85$^{\circ}C$ extracted more than 95% copper, iron, zinc, nickel and aluminium. Au and Ag were not extracted in this solution, however, more than 95% of Au and 100% of Ag were selectively leached with a mixed solvent (0.2M ammonium thiosulfate, 0.02M copper sulfate, 0.4M ammonium hydroxide). Finally, the residues were reacted with a NaCl solution to leach out Pb while sulfuric acid was used to leach out Sn. Recoveries reached 95% and 98% in solution, respectively.

• Advances in environmental research
• /
• v.3 no.4
• /
• pp.283-292
• /
• 2014

Iron precipitating organisms play a significant role in the formation of ferric hydroxide precipitate, which acts as strong adsorbent for toxic metal. In this respect four different iron precipitating cultures were isolated from Hutti gold mine surface winze water sample on citrate agar medium. The best isolate was screened out for metal removal study on the basis of fast visual iron precipitation. The selected isolate was identified as Enterobacter sp. based on routine biochemical tests and Biolog GN microplate results and as Enterobacter cloacae subsp. dissolvens by 16S rRNA gene sequence analysis (GenBank accession number EU429448). Influence of medium composition, medium initial pH, the influence of inoculum size, effect of various media and ferric ammonium citrate concentration were studied on metal removal in shake flask experiments. Under the optimized conditions studied, E. cloacae showed $94{\pm}2$, $95{\pm}2$ and $70{\pm}2%$ of cadmium, copper and mercury removal from a simulated waste in shake flask studies. In lab scale column reactor more than 85% of copper and mercury removal was achieved.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.3
• /
• pp.67-75
• /
• 2012

This paper presents an environment-friendly sand cementation method by precipitating calcium carbonate using plant extracts. The plant extracts contain urease like $Sporosarcina$ $pasteurii$, which can decompose urea into carbonate ion and ammonium ion. It can cause cementation within sand particles where carbonate ions decomposed from urea combine with calcium ions dissolved from calcium chloride or calcium hydroxide to form calcium carbonate. Plant extracts, urea and calcium chloride or calcium hydroxide were blended and then mixed with Nakdong River sand. The mixed sand was compacted into a cylindrical specimen and cured for 3 days at room temperature ($18^{\circ}C$). Unconfined compression test, SEM and XRD analyses were carried out to evaluate three levels of urea concentration and two different calcium sources. As urea concentration increased, the unconfined compressive strength increased up to 10 times those without plant extracts because calcium carbonate precipitated more, regardless of calcium source. It was also found that the strength of specimen using calcium chloride was higher than that of specimen using calcium hydroxide.

• Journal of the Korean Chemical Society
• /
• v.35 no.4
• /
• pp.422-426
• /
• 1991

In order to synthesize high-purity alpha alumina fine powder, the aluminum hydroxide and ammonium aluminum sulfate(alum) precursor were prepared from natural alumino-silicate(halloysite). The thermal decomposition mechenism for both precursors was elucidated by DTA/TG, XRD and IR analysis. The microstructure, specific surface area and purity of ${\alpha}-Al_2O_3$ were characterized by SEM, and BET analysis. The particle size of ${\alpha}-Al_2O_3$ was determined to be ${\phi}$ = 0.1∼0.5 ${\mu}$m. However, the specific surface area for the alum derived ${\alpha}-Al_2O_3$(89.0 m$^2$/g) was extremely higher than that for the aluminum hydroxide derived one(7.3 m$^2$/g).

• Korean Journal of Soil Science and Fertilizer
• /
• v.48 no.1
• /
• pp.1-7
• /
• 2015

Global population is expected to reach nine billion in 2050 and the total demand for food is expected to increase approximately by 60 percent by 2050 as compared to 2005. Therefore, it is important to increase crop production in order to meet the global demand for food. Slow release fertilizers have been developed and designed in order to improve the efficiency of fertilizers. Mineral-based slow release fertilizers are useful because the minerals have a crystalline structure and are environmentally friendly in a soil. This review focuses on slow release fertilizers based on montmorillonite, zeolite, and layered double hydroxide phases as a host for nutrients, especially N. Urea was successfully stabilized in the interlayer space of montmorillonite by the formation of urea-Mg or Ca complex, $[(Urea)_6Mg\;or\;Ca]^{2+}$ protecting its rapid degradation in soils. Naturally occurring zeolites occluded with ammonium nitrate and potassium nitrate by molten salt treatment could be used as slow release fertilizer because the occlusion process increased the capacity of zeolites to store nutrients in addition to exchangeable cations. Additionally, surface-modified zeolites could also be used as slow release fertilizer because the modified surface showed high affinity for anionic nutrients such as nitrate and phosphate. Moreover, there were attempts to develop and use synthetic layered double hydroxide as a carrier of nitrate because it has positively charged layers which electrostatically bond nitrate anions. Kaolin was also tested by combining with a polymer or through the mechanical-chemical process for slow release of nutrients.

• Korean Journal of Materials Research
• /
• v.15 no.10
• /
• pp.678-682
• /
• 2005

We studied the possibility of $Zn_4O(Ac)_2(OH)$ formation as a precursor for ZnO nano particles in sol-gel method. Four different additives such as tetra methyl ammonium hydroxide, mono ethanol amine (MEA), LiOH, and $H_2O$ were used for zinc acetate dissolved in 2-methoxy ethanol. ZnO particles of 5-6 nm in size were observed. Existence of $Zn_4O(Ac)_6$ was not verified. $Zn_4O(Ac)_2(OH)$ molecules were observed and they were believed to be the precursors of ZnO. A peak at 275nm in UV-Vis analysis was observed In the case of MEA and $H_2O$ but no ZnO particles were detected in transmission electron microscopy.

• Environmental Analysis Health and Toxicology
• /
• v.1 no.1
• /
• pp.77-80
• /
• 1986

Radiochemical synthesis of $N^{G}$-mono［$^{14}$ C-methyl］-L-arginine is described. The compound was synthesized from radio-active mono［$^{14}$ C］-methylamine as easily and purified by strong cation-exchange resin (NH form) liquid chromatography using a gradient of ammonium hydroxide, and crystallized as flavianate. The free amino acid was successfully prepared by strirring its flavianate and strong anion-exchange resin (OH- form), which could remove the flavianic acid from its salt in water below room temperature. Purity of the compound was tested by thin-layer chromatography, thin-layer electro-phoresis, and scintillation spectrometry.y.

• Electrical & Electronic Materials
• /
• v.10 no.5
• /
• pp.481-486
• /
• 1997

This paper describes the anisotropic etching characteristics of Si in acqueous TMAH/IPA solutions. The etch rates of (100) oriented Si crystal planes decrease with increasing TMAH concentration and IPA concentration. Etchant concentration and etch temperature have a large effect on hillock density. Hillock density strongly increase with lower TMAH concentration and higher etch temperature. The etched (100) planes are covered by pyramidal-shaped hillocks below TMAH 15 wt.%, but very smooth surface is obtained TMAH 25 wt.%. The addition of IPA to TMAH solution leads to smoother surfaces of sidewalls etched planes. Undercutting ratio of pure TMAH solution is much higher than KOH. But, addition of IPA to TMAh the underrcutting ratio reduces by a factor of 3∼4. Therefore, acqueous TMAH/IPA solution is able to use as anisotropic etchant of Si because of full compability with IC fabrication process.