• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.4
• /
• pp.233-239
• /
• 2013

This study was carried out to develop the realtime evaluation system of $NH_3$ absorption efficiency with gas sensors which were installed on the inlet and outlet of lab-scale scrubber system. The $NH_3$ absorption amount, calculated by sensor outcomes for 3 hr, 6 hr, and 12 hr of absorption process, was compared with the results analysed by Indo-phenol method for the absorption solution. Even though the difference between two methods was about 20%, the correlation coefficient between the two results was very high, more than 0.99. In addition, we could find very good correlation between pH, absorption amount and reaction time. Also we could find out the breakthrough time in the middle of absorption process. With more diverse experiment in the future, we can make gas sensor system for the realtime evaluation of the odor and/or air pollution treatment efficiency.

• Journal of Korean Society on Water Environment
• /
• v.34 no.3
• /
• pp.316-327
• /
• 2018

Liquid fertilizers made from livestock manure contain high concentrations of nitrogen and phosphorus and thus are used as a fertilizer. However, excessive use of liquid fertilizer causes eutrophication of agricultural land and nonpoint source pollution. In this study, as a means of lowering the nutrient concentrations, struvite ($MgNH_4PO_4{\cdot}6H_2O$) production from the liquid fertilizer was investigated. When liquid fertilizers produced in Gyeonggido were analyzed, its characteristics differed by region and season, but the phosphorus concentration was commonly lower than that of nitrogen. When $K_2HPO_4$ and $MgCl_2$ were added to the liquid fertilizers, the optimal pH for struvite formation was pH 9.5. For environmentally friendly sources of magnesium and phosphate, ferronickel slag (FNS) and sewage sludge ash (SSA) were suspended in deionized water and extracted by sulfuric acid with various mass ratios. The optimum conditions for extracting FNS and SSA were 4.0 M sulfuric acid and 0.35 mass ratio of sulfuric acid to sewage sludge ash, respectively. For forming struvite, 0.233 L of SSA leachate (SSAL) was added into 0.3 L of liquid fertilizer containing 2,586 mg/L of ammonia and 110 mg/L of phosphate, pH was then adjusted to pH 9.5 using 10 M of NaOH. Afterwards 0.333 L of FNS leachate (FNSL) was added to this mixed solution. After a reaction for 1 hr at room temperature, the remaining concentrations of magnesium, ammonium, and phosphate were less than 50 mg/L, 500 mg/L and 150 mg/L, respectively, and 30 g of precipitates were obtained, most of which were struvite.

• Applied Chemistry for Engineering
• /
• v.8 no.2
• /
• pp.332-338
• /
• 1997

$SnO_2$ as raw material of sensor for $NO_2$ detection was prepared by precipitating $SnCl_4$ solution with aqueous ammonia followed by calcining in air. The characterization of $SnO_2$ was carried out using FT-IR and XRD, and $SnO_2$ thick film sensor was fabricated by screen-printing method. The particle size of $SnO_2$ calcined at higher temperature increased due to the growth of crystalline. $SnO_2$ sensor fabricated by using $SnO_2$ sample calcined at $1000^{\circ}C$ followed by heat treatment at $700^{\circ}C$ exhibited excellent sensing characteristics and selectivity for $NO_2$ gas at the operating temperature of $250^{\circ}C$.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1996.06c
• /
• pp.692-700
• /
• 1996

The objective of this study is to develop a systematic purification plant using the metabolism of aerobic microorganisms. This system is subsequently aerated and continuously removes suspended solids and settling sludges caused by aerating pressure at the bottom of a lower pipe (i.e., Continuous Removal of Suspended solids and Settling sludges, CRSS). The CRSS plants are brought out by introducing fine air bubbles into the liquid phase of a lower pipe in the bio-reactor. These plant uses aeration pipe, with multiple inlets to sweep the floor of bio-reactor tank, instead of the conventional scraper mechanisms. The principal advantage of this system is that it can continuously remove very small or light particles that settles completely within a short time. Once the particles have been floated to the surface, they can be moved into the pipe and collected in the settling tank by sequently aerated pressure. The experimental results shows that about 99.0% of the biochemical oxygen demand(BOD), 99.3% of the suspended solid(SS), 92.3% of the total nitrogen(T-N), 99.0% of the turbidity(TU), 100% of the total coliform(TC)and ammonia was respectively removed during aerobic digestion for 9 days. These result indicates that the CRS S plants are very effective for reduction and deodorization of swine wastewater contaminants, and the efflux from CRS S can either be discharged in the river or used as nutrient solution of formulation for plant growth factories. The developed CRSS plant proved to be flexible and it can simply be adapted to any type of biological waste treatment problem.roblem.

• Textile Coloration and Finishing
• /
• v.23 no.1
• /
• pp.28-34
• /
• 2011

Deep coloration of cotton fabrics with concentrated Rhus verniciflua extract was carried out using large amount of Glauber's salt and a mordant in order to improve dyeability and functional properties such as deodorizing and antimicrobial activity. With increasing in the salt addition upto 80% in the dyeing liquor containing 0.45% extract concentration, K/S value and exhaustion increased threefold from 1.2 to 3.5, indicating that the salt reduced the electrostatic repulsion between the dyes and the cotton fibers. Also the concentrated extract solution to 8% can increase the color build up upto a K/S of 11.1. In addition the combined pre- and post-mordanting methods with potassium alum enhanced the dyeability upto a K/S of 22.2. The ammonia deodorizing property increased with increased color yield of the dyed fabrics. Also the dyed and post-mordanted fabrics with 8% extract concentration showed antimicrobial activity against both Klebsiella pneumoniae and Staphylococcus aureus.

• Journal of Adhesion and Interface
• /
• v.3 no.3
• /
• pp.15-21
• /
• 2002

The modified polyethylene(m-PE) films were prepared from aqueous dispersions which were synthesized by reacting poly(ethylene-co-methylacrylate) with aqueous KOH and ammonia solution to attach -COOK, $CONH_2$, and COOH as pendent groups in the polyethylene backbones. Thermal, tensile and heat-seal properties were measured to investigate the effect of the pendent groups. Endothermic peaks on DSC curves were affected by the thermal history of the samples and a melting peak was observed at around $86^{\circ}C$ on the second heating curve while three melting peaks were shown on the first heating curve. A minimum value of tensile strength was shown at 70 mole% of COOK based on pendent groups. Tensile modulus increased with increasing the amide content in pendent groups. The m-PE films were heat-sealed at lower temperature than LDPE films and showed a minimum heat seal strength at around 70 mole% COOK content in pendent groups.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.10
• /
• pp.2227-2232
• /
• 2009

Novel polythiol materials of urethane lens series for plastic optical lens were synthesized from polyol materials via thioisouronium of thiourea with c-HCl in refluxing aqueous solution, in which polythiol material was carried out from hydrolysis of thioisouronium by ammonia water. Their structure properties were identified by EA, EI-MS, FT-IR, $^1H\;and\;^{13}C$ NMR spectroscopies and TGA. Their ophthalmic lenses as polythiourethane material were prepared by thermal curing to an injected glass mold using the evenly solutions of diisocyanates series (TDI, XDI, HDI or IPDI) with polythiols. Polythiourethane shows that the strong stretching mode for SH group of polythiol disappeared in FT-IR spectra after thermosetting polymerization. Thermal deformation starting temperature of ophthalmic lenses was determined by TMA. Ophthalmic lenses made from characteristic polythiol and diisocyanate series have transparency, colorless and good impact strength, in which thermal resistance and impact strength of ophthalmic lenses were influenced by diisocyanate series. Physical properties of ophthalmic lens have contrast thermal resistance with impact strength. The property of thermal resistance and impact strength for respective ophthalmic lenses was examined by TMA and drop ball test.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.5
• /
• pp.516-520
• /
• 1999

Mechanical alloying (MA) by planetary type ball mill of pure iron powders was carried out under the ammonia gas atmosphere. The powders of metastable iron nitrides was synthesized up to the nitrogen content of 23 at% N. The observed phases are identified as the super-saturated bcc solid solution for the nitrogen concentration below 14.5 at% N and the non-equilibrium hcp phase stable at high temperature for 20.8 at.% N. Magnetization of Fe-N powders gradually decreases with increasing the N concentration on contrast to the enhancement reported for the bct iron nitrides. Neutron diffraction experiments also provide detailed information concerning the local atomic structure surrounding the nitrogen atoms. The coordination number of Fe atom around a nitrogen atom for the iron nitride containing 9.5 at% N turns out to be 3.9 atoms. This suggests that a nitrogen atom is situated at a center of the tetrahedron formed by iron atoms.

• Bulletin of the Korean Chemical Society
• /
• v.25 no.12
• /
• pp.1881-1888
• /
• 2004

A series of $NiO-TiO_2$/$WO_3$ catalysts was prepared by drying powdered $Ni(OH)_2-Ti(OH)_4$ with ammonium metatungstate aqueous solution, followed by calcining in air at high temperature. Characterization of prepared catalysts was performed by using FTIR, Raman, XPS, XRD, and DSC and by measuring surface area. Upon the addition of tungsten oxide to titania up to 25 wt%, the specific surface area and acidity of catalysts increased in proportion to the tungsten oxide content due to the interaction between tungsten oxide and titania. Since the -$TiO_2$/stabilizes the tungsten oxide species, for the samples equal to or less than 25 wt%, tungsten oxide was well dispersed on the surface of titania, but for the samples containing above 25 wt%, the triclinic phase of $WO_3$ was observed at calcination temperature above 400 $^{\circ}C$. The catalytic activities of 10-NiO-$TiO_2$/$WO_3$ for 2-propanol dehydration and cumene dealkylation were correlated with the acidity of catalysts measured by ammonia chemisorption method. NiO may attract reactants and enhance the local concentration of reactants near the acid sites, consequently showing the increased catalytic activities.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2874-2879
• /
• 2008

The Selective catalytic reduction(SCR) system is a highly-effective device of $NO_x$ reduction for diesel engines. Generally, the ammonia($NH_3$) generated from a liquid urea-water solution is used for the reductant. The ideal ratio of $NH_3$ molecules to $NO_x$ molecules is 1:1 based on $NH_3$ consumption and having $NH_3$ available for reaction of all of the exhaust $NO_x$. However, under the too low and too high temperature condition, the $NO_x$ reduction efficiency becomes lower, due to temperature window. And space velocity also affects to $NO_x$ conversion efficiency. This paper reviews a laboratory study to evaluate the effects of $NO_x$ and $NH_3$ concentrations, gas temperature and space velocity on the $NO_x$ conversion efficiency of the SCR system. The maximum conversion efficiency of $NO_x$ was indicated when the $NH_3$ to $NO_x$ ratio was 1.2 and the space velocity was $60,000\;h^{-1}$. The results of this paper contribute to improve overall $NO_x$ reduction efficiency and $NH_3$ slip.