• 한국반도체및디스플레이장비학회:학술대회논문집
• /
• 한국반도체및디스플레이장비학회 2007년도 춘계학술대회
• /
• pp.230-233
• /
• 2007

A system of anodic process of aluminum thin film has implemented for nanofabrication. The manufactured equipment consists of three main parts: chiller, reaction bath and power supply. The chiller module consists of refrigeration compressor, copper tube and coolant with a thermostat. The reaction bath has kept in same temperature as a thermodynamic canonical ensemble system during the anodic reaction process. The magnetic bar has stirred oxalic acid in bath for uniform reaction. The DC power supply has applied into two electrodes, aluminum for anode and platinum for cathode in the oxalic acid. The anodization process results in the formation of nanoporous thin films.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.728-731
• /
• 2003

This paper deals with a flat type ultrasonic motor, which uses a longitudinal-bending multi mode vibrator of rectangular form. A linear ultrasonic motor was designed by combination of the first longitudinal and eighth bending mode, and the motor consisted of a straight aluminum alloy bar bonded with piezoelectric ceramic elements as a driving element. The geometrical dimensions of the rectangular aluminum vibrator were determined by Euler-Bernoulli theory ANSYS was used to analyze the resonance frequency and the displacement of the stator vibrator. The resonance frequency of the motor provides the elliptical motion. and ANSYS was used to analyze elliptical motion and elliptical trajectory of stator vibrator when thickness of piezoelectric ceramics was varied respectively 0.763, 1.526, 2.289[mm] and width of stator vibrator was varied respectively 16, 12, 8, 4[mm]. When thickness of piezoelectric ceramics was decreased, the displacement of the stator vibrator was increased. And when width of stator vibrator was decreased, the displacement of the stator vibrator was increased.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 추계학술대회 논문집
• /
• pp.165-168
• /
• 2007

The objective of this study is to demonstrate and commercialized for on-board fuel storage system for the hydrogen fuel cell vehicles. Type3 composite cylinder is consisting of the full wrapped composites on a seamless aluminum liner. Especially, the seamless aluminum liner has been commercialized with development of fabrication through this study. The key technologies, including design, analysis and the optimized filament winding process for 350bar composite cylinder, were established and verified with design qualification test in accordance with international standard. And the facilities for fabrication and design qualification test have been constructed.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 1998년도 창립기념 춘계학술대회 논문집
• /
• pp.393-400
• /
• 1998

In this study, the crash situations and general crash analysis methods of railway rolling stocks were explained. To calculate the applied load and the maximum stress in the carbody when two aluminum railway vehicles were shunted, the finite element models for the carbody and the coupling system were made. The characteristic curve of draft gear which had a function to reduce impact force was modeled by nonlinear bar elements and the carbody was modeled by shell elements. Two shunting speeds, 5km/h and 8km/h, were considered and the results were analyzed and compared with static analysis case. Also, the aluminum railway vehicle with 60km/h was crashed against rigid wall to examine the global behavior of the carbody.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 추계학술대회 논문집 Vol.16
• /
• pp.304-307
• /
• 2003

In this paper, stacked piezoelectric ceramics were used for obtaining a large vibration for a small ultrasonic motor which is useable for the both linear drive and rotational drive. We studied this motor through the finite element analysis method and the simulated driving characteristics were presented. As results, the displacement of the tip of the stator was increased when the layers of the ceramics were increased. Also, by inserting additional aluminum plates between the ceramics and the aluminum bar, the displacement were amplified. In this model, two voltages which have 90 degree phase difference were applied for the bi-directional movement.

• 소성∙가공
• /
• 제7권1호
• /
• pp.66-71
• /
• 1998

The present study is concerned with the hydrostatic extrusion process of copper-clad aluminium bar to investigate the bonding conditions as well as the basic flow characteristics. Considering the bonding mechanism of bi-metal contact surface as cold pressure welding the normal pressure and the contact surface expansion are selected as process parameters governing the bonding conditions, in this study the critical normal pressure required for the local extrusion-the protrusion of virgin surfaces by the surface expansion at the interface-is obtained using a slip line method and is then used as a criteron for the bonding. A rigid plastic finite element method is used to analyze the steady state extrusion process. The interface profile of bi-metal rod is predicted by tracking the paths of two particles adja-process. The interface profile of bi-metal rod is predicted by tracking the paths of two particles adja-cent to interface surface. The contact surface area ration and the normal pressure along the interface are calculated and compared to the critical normal pressure to check bonding. It is found that the model predictions are generally in good agreement with the experimental observations. The compar-isons of the extrusion pressure and interface profile by the finite element with those by experi-ments are also given.

• 한국주조공학회지
• /
• 제34권3호
• /
• pp.87-93
• /
• 2014

Thixo-extrusion of semi-solid 7075 aluminum alloy and the mechanical properties of its extrudates were investigated. The semisolid alloy was prepared by a cooling slope cast. In other to perform thixo-extrusion, semi-solid 7075 aluminum alloy billets were reheated at the reheating conditions reported in a previous study. The maximum extrusion pressure in thixo-extrusion was 615MPa. This was lower than that of conventional hot extrusion ($P_{max}=940MPa$) at the same extrusion conditions due to the increased fluidity of the alloy billet in the semi-solid state. The values of Rockwell hardness (scale B) at the extrusion direction of the as thixoextruded bar were 48~53HRB and the difference in Rockwell hardness between the transverse direction and the extrusion direction was 5HRB or less. The results show that thxio-extrusion of semi-solid 7075 Al alloy improves the workability and anisotropic with the extrusion direction compared with hot extrusion of the conventional alloy.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2016년도 추계 학술논문 발표대회
• /
• pp.132-133
• /
• 2016

This research team has developed single silk white bubble sheets to be used as surface sheath curing material for spring, summer, and autumn. But though its effects for spring and autumn temperature conditions have been proved, there haven't been any studies for summer temperature conditions. Therefore in this study, single silk white bubble sheets and single silk transparent bubble sheets as well as aluminum metalizing single silk bubble sheets have been applied to actual box-frame apartment slabs in construction, in order to compare temperature backgrounds of the concrete and other qualities. Upon application, the temperature of concrete cured in summer temperature conditions showed excellent scores, being the lowest for aluminum metalizing single silk white bubble sheets, then single silk transparent bubble sheets. But the aluminum metalizing single silk bubble sheet gave off a harmful glare, so for actual use, white single silk bubble sheets are recommended.

• 한국주조공학회지
• /
• 제24권2호
• /
• pp.94-100
• /
• 2004

Gas porosity which is a common defect in aluminum alloy casting, is also thought to be severer in aluminum alloy castings produced by lost foam process due to the pyrolysis of the polystyrene foam pattern during pouring. Fundamental experiments were carried out to evaluate the effect of process variables such as the melt treatment, the cooling rate and pouring temperature on the density and mechanical properties in A356.2 castings with simple bar shape. The density of grain refined specimen was slightly lower than that of degassed one, but was higher than that of no treated one and that of shot ball packed specimen was higher than the other specimens. The tensile strength and elongation were in the ranges of $200{\sim}230MPa$ and $0.5{\sim}1.5%$ respectively. The density and hardness of lost foam cast specimens decreased with increase in pouring temperature.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 추계학술대회 논문집 Vol.16
• /
• pp.356-359
• /
• 2003

This paper deals with a flat type ultrasonic motor, which uses a longitudinal-bending multi mode vibrator of rectangular form. This ultrasonic motor was designed by combination of the first longitudinal and eighth bending mode, and the motor consisted of a straight aluminum alloy bar bonded with piezoelectric ceramic elements as a driving element. The geometrical dimensions of the rectangular aluminum vibrator were determined by Euler-Bernoulli theory In the experimental device, piezoelectric ceramics ( a piece of ceramic for the L-mode, $24\;{\times}\;8\;{\times}\;1[mm]$, and four pieces for the B-mode, $12.5\;{\times}\;8\;{\times}\;1[mm]$) were attached to one side of a aluminum plate($100\;{\times}\;8\;{\times}\;1[mm]$), and the stator was supported with a plastic case. As results, no-load rpm was 50[rev./m] when applied voltage was 150[Vrms] at the resonance frequency, and as the voltage was increased, the rpm was increased.