• Proceedings of the KWS Conference
• /
• 2001.10a
• /
• pp.199-201
• /
• 2001

• Journal of Korea Foundry Society
• /
• v.18 no.5
• /
• pp.481-487
• /
• 1998

Shell sand is widely used to make a complex shape castings due to its good collapsibility. When molten metal is poured into the mold, various gases are generated by the thermal decomposition of binder in the shell core. Casting defects such as blow hole and blister come from these gases. If it is possible to predict the evolution of gas quantitatively, it may provide effective solutions for minimizing the casting defects. To examine the gas evolution by shell core quantitatively, casting experiment and calculation were carried out. Gas pressure and gas volume evolved by shell core were measured in the experiment, and temperature distribution in the shell core was obtained by heat transfer analysis. From the result above, prediction on the gas volume evolved during pouring was tried. As forming pressure of the shell core increased and forming temperature decreased, the gas evolution increased. There was a close relationship between the calculated gas volume evolved and the measured one.

• Journal of Korea Foundry Society
• /
• v.32 no.1
• /
• pp.16-23
• /
• 2012

In this study, we develop the lower pressure die casting with rheo-forming process of A356 aluminum alloy and vacuum system which can control the crystal size and obtain the high strengthened-light material. Using this process, we fabricate the thin plate for bipolar plate through the low pressure die casting with electromagnetic stirring and vacuum-evacuation which can control the crystal grain by electromagnetic stirring. Thin plate ($110mm{\times}130mm{\times}1mm$) is fabricated by this process. The average Vickers hardness of thin plate is about 77 HV.

• Journal of Korea Foundry Society
• /
• v.30 no.4
• /
• pp.151-156
• /
• 2010

The high-strength low-alloy (HSLA) steels have low carbon contents (0.05~0.25% C) in order to produce adequate formability and weldability, and they have manganese contents up to 1.7%. Small quantities of silicon, chromium, nickel, copper, aluminum, molybdenum are used in various combinations. The results contained in this paper can provide the valuable information on the development of $-40^{\circ}C$ low temperature HSLA. Furthermore, the present experimental data will provide important database for casting steel materials of the offshore structure.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.337-340
• /
• 2006

Aluminum extruded profiles have been mostly used only a few automotive parts until now, such as roof rail, sunroof frame and bumper beams. However, Aluminum Extru-form technology, which was recently developed by foreign advanced manufacturer, made it possible to apply the aluminum extruded profiles to suspension parts of passenger and RV cars. It could be obtained by optimized billet casting, extrusion and stretch bending technology. It was possible to have the excellent weight reduction and the competitive price comparing with conventional process of aluminum for automotive parts. Combining additional process technology such as machining and joining, the application can be extended to various automotive parts. We have developed high strength aluminum alloy and fabricated subframe and suspension arm by extruforming process.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.2
• /
• pp.120-125
• /
• 2021

Phylon molds are widely used for injection molding of foams used in shoe outsoles. Injection pylon molds are usually prepared by first casting the aluminum alloy and then applying an anodized coating to improve durability. This study was carried out to examine the durability of aluminum phylon molds. The aluminum materials used in this study were A771, A6061, and AC4C, and their mechanical properties were compared. Specimens for anodic oxidation tests were prepared with coating thicknesses of approximately 10 and 40 ㎛. We tried to select the optimum material and coating thickness suitable for fabricating phylon injection molds. Among the three materials, A6061 exhibited the best tensile, wear, and impact properties. The difference in the wear resistance between the soft- and hard-anodized coatings was insignificant.

• Journal of the Korean Ceramic Society
• /
• v.32 no.2
• /
• pp.209-216
• /
• 1995

In order to investigate the effect o green microstructure on the sintering behavior and properties of AlN ceramics, samples were prepared by slip casting and dry pressing. The slip cast samples had high green density, fine pore size and narrow pore size distribution. They showed much higher sinterability and more homogeneous sintered microstructure compared to the dry pressed samples. Both increased thermal conductivity and flexural strength for samples prepared by slip casting could be attributed to the improved microstructural homogeneity with isolated second phase(s).

• IE interfaces
• /
• v.9 no.2
• /
• pp.129-141
• /
• 1996

Recently, the tire mold of a passenger car is made almost via aluminum casting, and it is necessary to prepare a master model of the tire for the casting. Because of the geometrical feature of tire, as well known, the master model must be machined by a 5-axis NC machine. The paper proposes a procedure to model and machine the master model. The approach includes (a) transformation of 2D drawing of tire into 3D geometry, (b) modeling surfaces of tire, and (c) inverse kinematics of a 5-axis NC machine. An implementation of the proposed procedure is also presented.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.337-341
• /
• 1997

The purpare of this research is to develope a FEM program for analyzing solidification processes of axisymmetic casting, considering phase changes and the contact between the metal and mold. Temperture recovery method is employed for considering the phase changes releasing the latent heat. A gap element is employed for modeling the interface between the model and metal in finding deformed shapes. In order to verify the developed program, an axisymmetric aluminum casting processes is simulated. Temperature distribution, phase front position, and shrinkaga and porosity creation are compared with measurement, FIDAP results, and ANSYS results, and good agreements are examined.

• Journal of the Korean Ceramic Society
• /
• v.39 no.3
• /
• pp.299-307
• /
• 2002

In this proposed study, a new emerging shape forming technique Direct Coagulation Casting(DCC) which enables to fabricate complex-shaped ceramic parts has been investigated using colloid surface chemistry. Various process variables affected by dispersant, coagulation agent and sintering additives, have been evaluated in order to achieve highly concentrated stabilized silicon nitride suspensions. A high solid loading of 51 vol% in the dispersed silicon nitride suspension was prepared with 1.0wt% Tetraethylammonium Hydroxide (TEAH), which obtained a stable silicon nitride suspension with sintering additives $(Al_2O_3\;and\;Y_2O_3)$ in alkaline regions. The addition of hydroxyaluminium diacetate into the suspension, which decomposed at elevated temperatures, led to coagulate of a silicon nitride suspension. In a basic medium, aluminum ions precipitated to aluminum hydroxide $(Al(OH)_3)$, leading to decreased $OH^-$ concentration and, thus, coagulated suspension.