• 한국주조공학회지
• /
• 제33권3호
• /
• pp.122-126
• /
• 2013

Recently, heat-resistant aluminum alloy has been re-focused as a downsizing materials for the internal combustion engines. Heat-resistant Al alloy development and many researches are still ongoing for the purpose of improving thermal stability, high-temperature mechanical strength and fatigue properties. The conventional principle of heat-resistant Al alloy is the precipitation of intermetallic compounds by adding a variety of elements is generally used to improve the mechanical properties of Al alloys. Heat resistant aluminum alloys have been produced by CrW homogeneous solid solution to overcome the limit of conventional heat resistant aluminum alloy. From EPMA, it is found that CrW homogeneous soild solution phases with the size of $50-100{\mu}m$ have been dispersed uniformly, and there is no reaction between aluminum and CrW alloy. In addition, after maintaining at high temperature of 573 K, there is no growth of hardening phase, nor desolved, but CrW still exists as a homogeneous solid solution.

• Composites Research
• /
• 제33권5호
• /
• pp.241-246
• /
• 2020

본 연구에서는 교반주조 공정을 통해 B₄C 입자가 균일하게 분산된 알루미늄 금속복합재료를 제조하고 후 공정으로 열간압연을 수행하였다. 제조된 복합재료의 미세조직, 기계적 특성 및 내마모 특성에 대해 분석하였다. 40 ㎛ 크기의 B₄C 입자가 균일하게 분산된 복합재료는 강화재의 체적율이 증가함에 따라 인장강도는 증가하였으며, 마모 성능도 개선되었다. 20 vol.% 복합재료의 경우 인장강도 값은 292 MPa로 기지재인 Al6061 대비 155% 증가하였다. 내마모시험 결과 20 vol.% 복합재료의 경우 마모 너비와 깊이가 각각 856 ㎛, 36 ㎛이며, 마찰계수는 0.382로 Al6061 대비 상당히 우수한 내마모 특성을 나타내었다.

• 한국주조공학회지
• /
• 제28권2호
• /
• pp.79-84
• /
• 2008

Metal foam is one of the most interesting materials with various multi-functional properties such as light weight, energy absorption, high stiffness and damping capability. Among them, energy absorption property has keen interests in the field of automotives for passenger protection. Nowadays, researches about pore size and porosity control of the foam are increased to correspond them. However, though energy absorption properties are improved, these results are not cost-effective process. In present research, however, as a part of improving the energy absorption property of metallic foams, 606X aluminum alloy was used for cell wall material which has higher strength than pure aluminum. And its morphological features are characterized. As a results, porosity and pore size are uniformity distribution with increasing foaming temperature in the case of 6061 alloy foams. 6063 alloy foam specimens have opposite tendency because of the influence of alloying element and viscosity of the molten melt.

• 한국주조공학회지
• /
• 제41권6호
• /
• pp.535-542
• /
• 2021

본 연구에서는 주철-알루미늄 이종재료의 계면결합강도를 향상시키기 위하여 탈흑연 열처리를 통해 주철 표면에서 일정 깊이까지의 흑연을 제거하였다. 열처리 시간이 증가함에 따라 흑연이 제거되는 깊이는 증가하였으며, 열처리 시간과 깊이 사이에 선형 관계가 나타났다. 일정 깊이의 흑연이 제거된 주철에 알루미늄을 다이캐스팅 공법으로 주조접합하여 주철에서 흑연이 제거된 공간을 알루미늄으로 채운 후, 계면 반응 및 알루미늄 침투 깊이를 조사하고 계면접합강도를 평가하였다. 다이캐스팅 공법을 통한 알루미늄은 탈흑연 열처리된 주철 표면에서 일정한 깊이까지 채워지는 것으로 확인되었으며, 주철-알루미늄 계면에 금속간화합물이 생성되지는 않은 것으로 확인되었다. 계면접합강도는 열처리 시간과는 큰 관계없이 90MPa 수준의 접합강도를 나타내었으며 이는 탈흑연 열처리를 하지 않은 소재의 접합강도 12MPa에 비해 매우 높은 강도이며, 주철의 탈흑연 영역에서 고압 다이캐스팅 공정에 의해 침투된 알루미늄 용탕이 응고되면서 언더컷 구조의 기계적 결합에 의한 것으로 생각된다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 추계학술발표대회 논문집
• /
• pp.131-134
• /
• 2002

Braided carbon fiber reinforced Al matrix composites were developed and characterized. Braided carbon fiber preforms with braiding angles of $30^{\circ}$, $45^{\circ}$ and $60^{\circ}$ were manufactured by using a braiding machine. The manufactured braided carbon fibers were used as reinforcement to fabricate Al matrix composites by employing a pressure infiltration casting method. In the processing of pressure infiltration casting, important processing parameters such as melting temperature, preheating temperature of preform and applied pressure were optimized. Prediction of elastic constants on composites was performed by using the volume averaging method, which utilizes the coordinate transformation and the averaging of stiffeness and compliance constants based upon the volume of each reinforcement and matrix material. The elastic moduli of composites were evaluated by using Resonant Ultrasound Spectroscopy(RUS) method and compared with the elastic moduli obtained from static tensile test method.

• 한국주조공학회지
• /
• 제43권4호
• /
• pp.187-193
• /
• 2023

쉘 중자 공법은 성형성, 탈사성에 있어서는 뛰어난 프로세스이나, 고온의 알루미늄 용탕이 중자와 접촉할 때 수지의 열분해에 의한 가스발생이 필연적이며, 이의 배출이 원활하지 못할 때에는 주물내부에 기공 등으로 남게 되어 주조품의 내기밀성에 직접 영 향을 미친다. 쉘 중자 이용 시 가스발생거동에 대해서는 일본에서 약간의 연구가 있었으나, 직접적인 예측 결과는 발표되지 않았고, 특 히 가스발생에 대한 모델링이 성립되어 있지 않아 이의 연구는 아주 미미한 상태이다. 개발되는 코어에 대한 온도-가스량과의 관 계를 고려한 발생 가스량 시뮬레이션 프로그램을 개발하고, 이를 이용하여 실린더 헤드 제품의 코어 금형 설계 및 저압주조 시 금속 용탕의 유동 및 응고 거동을 해석하고 주조결함 발생을 예측하여 결함발생을 최소화 하는 주조방안 도출하고자 한다.

• 한국주조공학회지
• /
• 제29권1호
• /
• pp.27-32
• /
• 2009

The microstructure of Al-7Si-0.4Mg-1Fe alloy mainly consists of aluminum dendrites, Al-Si eutectics, and $Al_5FeSi$ needles. When Mn was added to the alloy, the substantial amount of $Al_5FeSi$ phase was changed into Al(Mn,Fe)Si, however the needle-like morphology was almost unchanged. Combined additions of Cr or Sr with Mn to the base alloy resulted in rod-like Al(Mn, Fe,Si)Si phase. The tensile properties of as-cast alloys were enhanced by the Mn addition, especially when it was added with Sr. The tensile properties after T6 heat treatment was a little improved with 0.7%Mn addition, but Cr or Sr additions with Mn didn't show any positive effect on the properties of heat-treated alloys.

• 한국주조공학회지
• /
• 제30권1호
• /
• pp.29-33
• /
• 2010

The microstructure of Al-5%Mg based alloy mainly consists of aluminum matrix with a small amount of AlMn phase. The addition of Sc or Zn to the base alloy significantly improved the as-cast tensile strength, while the addition of Fe deteriorated both strength and ductility. Although the Al-5%Mg based alloy was not heat-treatable, aging hardening could be observed in the case that Sc or Zn was added to the base alloy. TEM analysis showed that very fine AlSc or AlMgZn precipitates were formed after T6 heat treatment, resulting in enhanced strength. The corrosion resistance measured as corrosion potential was found to decrease a little by adding Zn, whereas other alloying elements were not clearly influential.

• 한국주조공학회지
• /
• 제23권5호
• /
• pp.268-275
• /
• 2003

The mechanism of the hydrogen gas pore formation was investigated in Lost Foam Casting of Al-alloy by reduced pressure test and real casting. The hydrogen gas pick-up was affected by the formed gas during the decomposition of polystyrene in addition to the liquid product. It depended on pouring temperature and a proper temperature of metal front gave the minimum hydrogen pick-up. At a low pouring temperature, the hydrogen went into the melt mainly from entrapped liquid product of polystyrene but pores were formed from the gas as well as the liquid product at a high pouring temperature. The mold flask evacuation down to 710torr decreased the gas porosity down by around 0.4% vol%. The entrapped decomposition product of polystyrene in the melt was observed through the visualization of filling behavior of Al alloy-melt with the high speed camera.

• 한국주조공학회지
• /
• 제19권5호
• /
• pp.410-418
• /
• 1999

To overcome the undesirable deformation, peeling off and geometrical restrictions which were mainly caused by differences in thermal expansion coefficients during the cladding of aluminum strip and stainless strip, new processing method based on vacuum die casting is designed and implemented in fabricating Fe-17wt%Cr steel (stainless steel). To increase cast-bonding ability, the surface of Fe-17wt%Cr steel is electrochemical etched to have optimum pit size (above 0.2 mm) and pit density (above 30%). The implementation of vacuum die casting by using surface treated stainless steel (Fe-17wt%Cr Steel) produces good trial products having acceptable cast-bonding ability. The enabling conditions for cast-bonding are pouring temperature $690^{\circ}C$, filling speed 30 m/sec and casting pressure $800\;kg/cm^2$. The microscopic observation of cast-bonded Al/Fe-17wt%Cr steel does not show any evidence of intermetallic compounds. The bonding strength of trial products is $150-400\;kg/cm^2$ and this is stronger than conventionally cladded metal having $30-70\;kg/cm^2$.