• 한국정밀공학회지
• /
• 제23권10호
• /
• pp.60-67
• /
• 2006

This paper presents the temperature control in aluminum plate with Peltier module. From the experimental work, Peltier module is used to control the temperature of small aluminum plate for both heating and cooling with the control of current and fan ON/OFF. And current control of Peltier module was accomplished by PWM method. As a result of experiments, it is proper that operate cooling fan only while cooling duration and there exist a proper cooling current to drop temperature rapidly. It takes about 125sec to control temperature of aluminium plate between $30^{\circ}C$ and $70^{\circ}C$ and about 70sec between $40^{\circ}C$ and $60^{\circ}C$, in ambient temperature $28^{\circ}C{\sim}29^{\circ}C$ while cooling fan is operated only cooling duration. With the cooling current, temperature control of aluminum plate was accomplished more rapidly in comparison without cooling current. Future aim is to realize more rapid temperature control and develop SMHA(special metal hydride actuator) by using Peltier module as a heating and cooling source.

• Journal of Welding and Joining
• /
• 제21권2호
• /
• pp.57-63
• /
• 2003

Since new types of vehicles or structures made from thin aluminum alloy are under rapid development and some products are already on the market, welding of aluminium sheet is increasing. MIG(Metal Inert Gas), MIG-Pulse, TIG(Tungsten Inert Gas) welding are the typical Ai welding. MIG welding has the advantage of high speed, but it is difficult to apply to the thin plate, because of bum-through by the high heat input and spatter. MIG-Pulse welding can weld without spatter and burn-through, but when the gap exists at the welding joint, there is quite a possibility of bum-through. TIG welding is difficult to weld at a high speed. AC Pulse welding alternates between DCEP(Direct Current Electrode Positive) and DCEN(Direct Current Electrode Negative). DCEN is higher wire melting rate than DCEP, while lower temperature of droplet than DCEP. In AC Pulse welding, far fixed welding current, wire melting rate increases as the EN ratio increases. For fixed wire feed rate, welding current decreases as the EN ratio increases. Because of these features, the temperature of droplet, the depth of penetration, the width of bead decrease and the reinforcement height increases as EN ratio increases, and these are able to weld at a high speed, lower heat input. It is the purpose of this study that design of AC pulse current waveform for MIG welding of Al sheet and estimation of output characteristic.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 C
• /
• pp.1893-1895
• /
• 2001

In this paper, novel release technique using wet etch is proposed. The results of this technique and the results of SAMs (Self-Assembled monolayers) coated after release using this technique are compared. Fabricated structure have 100 um in width and experimental length is from 100 um to 1 mm. Thickness of aluminum sacrificial layer is 2 um and structure thickness is 2.5 um. Cantilevers and bridges are fabricated with electroplated gold and silicon nitride deposited on substrate. An aluminium sacrificial layer was evaporated thermally and removed in various wet etching solutions. Detachment length of cantilever is 200 um and detachment length of bridge is 1 mm after isooctane rinsing. And the SAMs coating condition which is appropriate for gold and nitride are studied respectively.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 춘계학술대회 논문집(한국공작기계학회)
• /
• pp.422-428
• /
• 2001

The term High Speed Machining has been used for many years to describe end milling with small diameter tools at high rotational speeds, typically 10,000 - 100,000 rpm. The process was applied in the aerospace industry for the machining of light alloys, notably aluminium. In recent year, however, the mold and die industry has begun to use the technology for the production of components, including those manufactured from hardened tool steels. With increasing cutting speed used in modern machining operation, the thermal aspects of cutting become more and more important. It not only directly influences in rate of tool wear, but also will affect machining precision recognized as thermal expansion and the roughness of the surface finish. Hence, one needs to accurately evaluate the rate of cutting heat generation and temperature distributions on the machining surface. To overcome the heat generation, we used to cutting fluid. Cutting fluid play a roles in metal cutting process. Mechanically coupled effectiveness of cutting fluids affect to friction coefficient at tool-work-piece interface and cutting temperature and chip control, surface finish, tool wear and form accuracy. Through this study, we examined the behavior of heat generation in high-speed machining and the cooling performance of various cooling methods.

• 대한의생명과학회지
• /
• 제16권4호
• /
• pp.323-330
• /
• 2010

Although copper and zinc are essential metals for human health, excessive level of these metals is toxic. Besides, aluminum is known to induce various adverse health effects including neurological disorders. Therefore, monitoring the human body burden of these metals is important in preventing adverse health effects. In this study, we assessed the exposure to copper, zinc, and aluminum among an adult population residing in Daegu and Kyungbuk areas. Based on data from 171 participants, we found that the geometric mean copper, zinc, and aluminum concentrations in hair were $15.1\;{\mu}g/g$ [95% confidence interval (CI): 13.1~17.5], 76.9 (95% CI: 70.4~84.1), and $1.11\;{\mu}g/g$ (95% CI: 0.81~1.51), respectively. The copper concentrations in hair were significantly related to age, education, and residence area. In addition, zinc concentrations in hair were significantly related to age, whereas higher hair aluminum concentrations were related to alcohol drinking. Correlations between copper and zinc in hair had a significant positive correlation. Our findings suggest that the body burden of copper, zinc, and aluminum varies according to demographic factors, and hair could be used as a valuable biological medium for metal exposure.

• 한국세라믹학회지
• /
• 제31권5호
• /
• pp.552-560
• /
• 1994

A composite of TiB2-Al2O3 system was successfully prepared from a mixture of TiO2, B2O3, and Al by self-propagating high temperature synthesis (SHS) with a novel characteristic, utilizing the internal oxidation heat of aluminium metal of the mixture, instead of by a conventional technique, externally heating a mixture of Ti, B and Al2O3. From a mixture with B/Ti molar ratio of =2.0, pure two phases of TiB2 and $\alpha$-Al2O3 with good crystallinity and small, uniform sizes were formed. However, when the B/Ti molar ratio of the mixture goes to a value less than 2.0, in addition to the above main minerals, a small smounts of metastable phases such as TiB and Ti3B4 were formed. It was found that about 60%, the optimum green density of compacts gave their highest reaction rate and temperature during SHS process. TiB2-Al2O3 system composite with B/Ti molar ratio of =2.0 could be pressurelessly sintered even at 190$0^{\circ}C$ under Ar gas flows without any addition of sintering aids, showing their good properties such as 91.2% in relative density, 2750 kgf/$\textrm{mm}^2$ in Vickers hardness and 2620 kgf/$\textrm{cm}^2$ in flexural strength.

• 한국환경과학회:학술대회논문집
• /
• 한국환경과학회 2003년도 International Symposium on Clean Environment
• /
• pp.159-164
• /
• 2003

Effects of Al on vitellogenin (VTG) and VTG mRNA induction by estradiol-17 $\beta$($E_2$) were examined in primary hepatocyte culture of rainbow trout. Hepatocytes were precultured for 2 days and then E2 ($2{\times}10^{-6}$M) and Al ($10^{-6}-10^{-4}$M) were simultaneously added to the incubation medium. Hepatocytes were cultured for 5 more days. Media and hepatocytes were then analyzed by SDS-PAGE and Northern blotting for VTG and VTG mRNA, respectively. These metal had no appreciable effect on the viability of hepatocytes in culture. However, Al interfered with VTG production and VTG mRNA expression. Al reduced VTG production in a concentration-dependent way and a significant reduction accurred at Al concentrations greater than $5{\times}10^{-5}$M. VTG mRNA expression also decreased with a negative correlation with Al concentration (r＝-0.98). These results suggest that Al inhibit VTG production at the transcriptional level to reduce VTG mRNA expression.

• 한국주조공학회지
• /
• 제17권1호
• /
• pp.93-99
• /
• 1997

A possibility of production of aluminium matrix composites by using the lost foam process was investigated. Silicon carbide particles, graphite particles, and stainless steel wires were used as reinforcement materials. The reinforcement materials were introduced to the polystyrene to form patterns via injection molding process. The results obtained from this experiment can be summarized as follows. In Al/SiCp system, the particles with the radius of $100{\mu}m$ and over were entrapped in the matrix in the case of upward freezing of which solidification direction was opposite to floating direction of the particles. And few particles were entrapped in the matrix in downward freezing. In Al/graphite system, almost no particles were entrapped in the matrix except the area chill attatched. When the thickness of polystyrene slice was 4mm in Al/stainless steel wire system, the floating tendency of fibers was observed to increase as the distance from the ingate was increased.

• 대한기계학회논문집A
• /
• 제21권2호
• /
• pp.346-351
• /
• 1997

The creep characteristics of an Al-5wt.% Ag alloy including the stress exponent, the activation energy for creep and the shape of the creep curve were investigated at a normalized shear stress extending from $ 10^{-5}{\;}to{\;}3{\times}10^{-4}$ and in the temperature range of 640-873 K, where silver is in solid solution. The experimental results shows that the stress exponent is 4.6, the activation energy is 141 kJ/mole, and the stacking fault energy is $180{\;}mJ/m^2$, suggesting that the creep behavior of Al-5 wt.% Ag is similiar to that reported for pure aluminum, and that under the current experimental conditions, the alloy behaves as a class II(metal class). The above creep characteristics obtained for Al-5 wt.% Ag are discussed in the light of prediction regarding deformation mechanisms in solid solution alloys.

• 한국자동차공학회논문집
• /
• 제4권4호
• /
• pp.130-139
• /
• 1996

The silicon carbide particles reinforced aluminium 6061($SiCp/A\ell$) composites are generally known have wild range of applications from automobiles to airospaces. But, by the results of existing study for $SiCp/A\ell$ composites, there are reports that the fatigue life of $SiCp/A\ell$ composites has improved than $A\ell$matrixes and has not improved then $A\ell$ matrixes. Consequently, in order to perform the reliable life prediction for $SiCp/A\ell$, the properties of probability distribution of fatigue crack initiation life & fracture life, crack growth length in constant number of cycles, crack growth rate in constant stress intensity factor range and m & C value in Paris's fatigue crack growth law and the estimation of statistical parameters have been evaluated by the statistics method.