• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.4
• /
• pp.39-45
• /
• 2012

In this paper, process conditions are investigated for elimination of the grain coarsening and improved material flow during forging process by both of experiments and FEM analysis. Particular interest has been given to understand role of preform shape on the grain coarsening behavior and magnitude of the hammer forging load. As the results of FEM simulation by using DEFORM-3D, the simulated forging loads were 2,200ton in the case of a machined bar which is machined from 65mm to 60mm diameter, and below 1,900ton in the case of machined preform, respectively. The use of preform has been beneficial for reduction of the forging load and elimination of the grain coarsening. However, in the case of as received bar and the round bar, which was machined to 2.5mm thickness in surface layer, some degree of local grain coarsening behavior has been observed. The optimized preform shape could be properly designed by applying the FEM simulation.

• Transactions of Materials Processing
• /
• v.9 no.4
• /
• pp.379-388
• /
• 2000

This study aims to examine the influence of experimental and numerical factors on the results of the test and finite element simulation to evaluate the formability of sheet metals. The stretch-forming test with a hemispherical punch is carried out to obtain the limiting dome height (LDH) and forming limit diagram (FLD) for several kinds of aluminium and steel sheet. The results of the LDH and FLD tests are analysed to find any correlation with the uniaxial tensile properties. It proves that the size of the prescribed grid has great influence on the measured value of strain. The finite element analysis of the punch stretching process is also carried out and the result is compared with the experimental data. The influence of the numerical parameters such as friction coefficient, element size and anisotropy model on the simulation results tms out to be very considerable.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1991.04a
• /
• pp.251-255
• /
• 1991

The primary objectives of the rolling process are to reduce the cross section of the incoming material while improving its properties and to obtain the desired section at the exit from the rolls. Many engineering metals, suchas aluminium alloys, copper alloys, and steels are often cast intoingots and are then further processed byhot rolling into blooms, slabs, and billets, which are subsequently rolled into other products such as plate, sheet, tube, rod, bar, and structural shapes. In shape rolling a round or square bar is rolled in several passes into various shapes. During eachpass, the bar elongates as well as spreads. Thus, a very complex three-dimensional metal flow takes place. In this paper TASKS results for the simulation of a 7 pass square-to-round shape rolling are presented. The results are verified by comparing it with experimental results from a previous study conducted at the Battelle Columbus Labs

• Transactions of Materials Processing
• /
• v.8 no.2
• /
• pp.188-199
• /
• 1999

Semi-Solid Forming Process(Thixoforming, Rheocasting) is a novel forming process which has some advantages compared with conventional die casting, squeeze casting and hot/cold forging. In this study. Thixoforming process was selected as analysis processing in terms of billet handling and easiness of automation process. The Thixoforming process consists of reheating process of billet, billet handling, filling inot the die cavity and solidification of SSM part. In filling process, two rheology models which were Newtonian and Non-Nettonian model (Ostwald-deWaele)were verified with experimental results. The Ostwald-deWaele model shows the good agreement to the real flow and filling phenomena in die cavity. To give a boost the economical efficiency of Thixoforming process and to ensure the good forming result, reheating device coupled die set was proposed and the initial billet temperature for system that was found from experimental resluts. This study presents an overview of application of numerical analysis for simulation of semi-solid metal forming process to reduce the lead time for development of manufacturing part in industrial field.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.845-848
• /
• 2002

The wrinkling in the flange and wall of a part is a predominent failure mode in stamping of sheet metal parts. In many cases this wrinkling may be eliminated by appropriate control of the blank holding forco(BHF), but BHF affects the draw depth. Gotoh had studied the wrinkles under 0.02mm in height. In general, the height of wrinkles could be limited under 0.2mm practically. Therefore small BHP can be allowed so that the depth of drawing could be increased. Authors research the variation of the wrinkles in flange in the course of cup drawing by using aluminium alloy Al050 and A5052.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.10 s.175
• /
• pp.129-136
• /
• 2005

The demand on thermos furnace of Al molten metal has recently been getting higher and higher according to the increase in use of Al and Al alloys. This study considers the estimation of the thermal and mechanical stability in the thermos furnace for Al casting. It is executed through the analysis of heat transfer on the refractory material and heat stress on each steel shell. Also, the estimation of structural stability was appraised through the strength analysis of the lower structure. In result, the temperature of steel shell rose to 320.15K and its elastic deformation was about 1.5mm. The elastic deformation of the lower structure was about 0.66mm. As a result of it, the data obtain from the analysis in this study are regarded as stable value on considering that the size of the furnace is 2500mm.

• Journal of Welding and Joining
• /
• v.16 no.2
• /
• pp.57-63
• /
• 1998

This study deals with the friction weldability of machine structural carbon steel (SM45C) to Al-Mg-Si aluminium alloy (A6063). The bonding strength of friction welded joints, from all mechanical test, exceeded that of A6063 base metal, under the condition of friction time 1.5 sec, upset pressure 80MPa. The friction welded joints under these conditions exhibited tensile strength of 262MPa, bending angle of 90$^{\circ}$ without crack at weld interface and shear strength of 113MPa. Consequently, the friction weldability of SM4C to A6063 was very excellent, and that was possible without special preparation of weld surfaces.

• Journal of Welding and Joining
• /
• v.35 no.3
• /
• pp.75-81
• /
• 2017

Recently in the welding field, the establishment of unmanned and automated systems are rapidly developing. Accurate interpretation of the welding phenomenon is applied a number of monitoring systems. In this paper, butt welding (6t) type I using Plasma-MIG welding was carried out. And we evaluated characteristics of the Al-5083 aluminium alloy in Plasma-MIG hybrid welding. Process variables including the plasma current, MIG voltage, wire feeding rate and the welding speed were used. Butt welding was conducted 1 pass. Argon gas was used as the protective gas that results from the experiment were able to achieve full penetration. In addition to monitoring the welding process occurring during MIG welding current, welding votage and Plasma current, voltage were collected in real time, the photodiode and CCD cameras observing the phenomenon that the welding is in progress were measured using a quantity of light.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.5
• /
• pp.811-815
• /
• 2007

A series of bispyrenyl-polyether have been synthesized and investigated as a fluorescent chemosensor for metal ions. The results showed that bispyrenyl-polyether system is selective towards Al3+ ion over other ions tested. In free ligand, excited at 343 nm, it displays a strong excimer emission at around 475 nm with a weak monomer emission at 375 nm. A ratiometry of monomer (375 nm) increase and excimer (475 nm) quenching was shown only when Al3+ ion is bound to ligand, because two facing pyrene groups form a less efficient overlap of π?π stacking compared with that of free ligand.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2008.11a
• /
• pp.68-68
• /
• 2008

There are several methods for oxide coating on metals, such as aluminum or carbon nanotubes(CNTs). Usually CVD method is introduced for various oxide coating on CNTs. Another method is electrochemical method which use potential-pH diagram for oxide coating on metal or CNTs. In this experiment, electrochemical coating parameter for oxide coating on aluminum template modified by acids and hydrogen peroxide ($H_2O_2$) were examined. SEM micrographs displayed clearly $Ni(OH)_2$ coating on template. For confirmation of electrochemical method application to EDLC electrode material fabrication, EDS spectrum was analyzed.