• 한국세라믹학회지
• /
• 제47권3호
• /
• pp.232-236
• /
• 2010

In recent years abrasive water jet (AWJ) has received significant attention as a technology used in the manufacturing industry for cutting materials. In this paper we report the development of a new preparation method of abrasives for water jet by using an air bubbling sedimentation rate control technique. The SiC abrasives prepared by an air bubbling sedimentation rate control technique using latex resin are found to be superior to the conventional abrasives not only in surface roughness uniformity but also in lifetime. The AWJ test results also show that the former has also better impact-resistance and wear-resistance than the latter.

• 한국세라믹학회지
• /
• 제13권2호
• /
• pp.3-7
• /
• 1976

Influences of chlorides(CaCl2, MgCl2, NaCl) on the colouring effect of Fe component in white portland cement was investigated. Chlorides enhance the whiteness of the white portland cement owing to volatilization of Fe2O3 and translation of ferrite composition toward C2F. This translation is caused by consumption of alumina at the formation of C12A7, the formation of which is promoted in the presence of chloride. With decrease of p in ferrite composition C6F1-pAp, transfer of Fe3+ from 4 to 6 coordinated cite is occurred, and as a result, whiteness is raised. Hydration process of the cement containing a small amount of chloride differs little from the one without chloride.

• 한국세라믹학회지
• /
• 제29권5호
• /
• pp.403-409
• /
• 1992

The titania membrane thickness coated on the porous alumina support by the sol-gel method was analyzed using the slipcasting model. The thickness of calcined membrane layers increased linearly from 1.3 to 3.8 ${\mu}{\textrm}{m}$ with the square root of the dipping time (4~40 min). Growth rates of the thickness of wet gels and calcined layers were well described quantitatively by the slipcasting model. Through the regression of experimental data using model equations, the permeability and the pressure drop across wet gels, and the thickness and their growth rate constants of wet gels and calcined layers could be determined. It was also known that the gellation concentration of the TiO2 sol used in this work and the porosity of wet gel layes were 25 mol/ι and 0.53, respectively.

• 한국세라믹학회지
• /
• 제31권12호
• /
• pp.1513-1520
• /
• 1994

Mechanical properties of hot-pressed SiC whisker/Al2O3 composites were strongly dependent on the granular characteristics of mixed powder, which were controlled by co-dispersion condition, the existence of steric barrier on whisker surface, and granulating method, etc. Heat-treatment of SiC whiskers at $700^{\circ}C$ for 1 hr in air was very effective both for achieving dispersion stability of whiskers with PVA adsorption and for obtaining excellent mechanical properties of resulting composites. It is believed from the fractography of composites prepared with various whisker dispersion conditions that the most common fracture origin of Al2O3 agglomerate could be attributed to whisker clusters arising due to flocculation. Further improvement of mechanical properties of composites were achieved by hot pressing green tapes prepared by Doctor-blade process, which promoted two-dimensional random alignment of whiskers.

• 한국세라믹학회지
• /
• 제28권9호
• /
• pp.712-720
• /
• 1991

The effect of cyclic compressive stress on fracture responses of Al2O3 was investigated under uniaxial stress cycling. Experimental data were obtained for Al2O3 tension specimens under uniaxial tension-unloading and tension-compression cyclic loading conditions. To investigate the effect of compressive stress on the crack growth, theoretical results from the crack growth rate were compared with measured stress vs. failure relations. At low stress level in tension-compression cycling, residual tensile strains were also observed about failure time.

• 한국세라믹학회지
• /
• 제27권3호
• /
• pp.369-382
• /
• 1990

ZrO2-Toughened Alumina-Ceramics(ZTA) with Cr2O3 and HfO2 as addition were synthesized by assintering method for solid solution of Al2O3/Cr2O3 and ZrO2/HfO2, and were prepared by pressureless sintering at 1$600^{\circ}C$. The effects of Cr2O3 and HfO2 on the thermal and mechanical properties, the sintering mechanism, and the wearness between theory and experiment were investigated. Among three kinds of mechanisms such as stress-induced transformation, microcracking, and crack deflection it contributed to the ZTA system with a few exceptons according to composite. We show that wearness can be estimated sufficiently by HV and KIC through theory and experiment.

• 한국세라믹학회지
• /
• 제28권7호
• /
• pp.549-555
• /
• 1991

Mullite-zirconia (0∼4 mol% yttria) composites were obtained by In-situ sintering of zircon and alumina mixture, and their mechanical properties were studied in conjuction with microstructure observation. Martensitic transformation temperature (Ms) of zirconia dispersed in the mullite matrix decreased with Y2O3 contents and was about 600$^{\circ}C$ for ZrO2 containing 4 mol% Y2O3. On cooling of this composites, tetragonal to monoclinic phase transformation induced microcracks at the grain boundary of mullite matrix. The microcracks seemed to absorb the fracture energy in stress field during mechanical tests. Therefore, toughening mechanisms of this composite were considered to nucleation and extension of microcrack, and crack deflection mechanism due to the difference of thermal expansion coefficient between matrix and dispersed phase.

• 한국세라믹학회지
• /
• 제28권9호
• /
• pp.696-704
• /
• 1991

ZrO2-Toughened Alumina-Ceramics (ZTA) with SiC Whisker as dispersive additive were prepared by pressureless sintering at 1$600^{\circ}C$ and 1$650^{\circ}C$ and by HIPing at 1$600^{\circ}C$ in Ar atmosphere. Effects of SiC-Whisker addition on microstuructural, mechanical, and thermal properties were investigated and the toughening mechanisms between theory and experiment were compared. Specimens with 15 vol% Whisker prepared by HIPing showed 8.26 MPa.ma1/2 in fracture toughness and 600 MPa in flexural strength owing to contribution of the three mechanisms such as crack deflection, whisker bridging and whisker pullout in spite of difference between the theoretical and experimental values due to the partial inhomogeneous dispersion of SiC-Whisker in the matrix and the processing flaw.

• 한국세라믹학회지
• /
• 제34권11호
• /
• pp.1139-1150
• /
• 1997

A model for predicting the relative density and the compressive strength of open-cell ceramics with three-dimensional network structure was proposed through the interpretation of their macrostructure and fracture mechanics. The equation predicting the relative density was derived under the assumption that the open-cell structure was a periodic array of the tetrakaidecahedron unit cell consisting of cylindrical struts containing the internal hollow with the shape of a triangular prism. The model for compressive strength of open-cell ceramics with the hollow strut was also developed by modifying conventional model which based on fracture behavior of them subjected to the compressive stress. Both the relative density and the compressive strength were expressed in terms of the ratio of the strut diameter to the length together with the ratio of the hollow size to the strut diameter. The proposed model for the relative density and the compressive strength of the alumina-zirconia composite with open-cell structure were accorded well with the experimental values, whereas Gibson-Ashby and Zhang's model did not show such a good agreement.

• 한국세라믹학회지
• /
• 제30권2호
• /
• pp.157-163
• /
• 1993

Hot pressing after cold cyclic compaction of Al2O3 powder mixtures containing SiC whiskers or Al2O3 short fibers is studied with emphasis on the effects of cold cyclic compaction. The green density of the mixtures increases as the cycle number increases and the cyclic pressure becomes higher. The higher green density is also obtained by cold cyclic compaction with the lower pressrue than a single stroke cold compaction. To achieve a higher densification during hot pressing, cold cyclic compaction before hot pressing is more efficient compared to the conventional hot pressing process (without cold cyclic compaction). Moreover, a low cyclic pressure did not affect on toughening mechanism by whisker reinforcement.