• Asian Journal of Turfgrass Science
• /
• v.25 no.1
• /
• pp.1-10
• /
• 2011

This study was conducted to investigate early germination characteristics and germination pattern of new cultivars of creeping bentgrass (CB, Agrostis pall/stris Huds.) under natural room temperature conditions and to analyze differences between alternative and natural conditions. Seven cultivars of CB were tested in the study. Daily and cumulative germination patterns were measured and analyzed on a daily basis. Significant differences were observed in germination pattern, days to the first germination, days to 50% germination, days to 85% germination, and germination rate among cultivars under different environments. The first germination in all entries was initiated between 4 and 5 days after seeding (DAS) under alternative conditions, while between 6 and 8 DAS under natural conditions, being 2 to 3 days later as compared with that of alternative conditions. As for the first germination percentage, it was generally 5 to 25% under alternative conditions. However, 'Penn A-1', 'Penncross', and 'Penn A-4' cultivars showed a vigorous germination, producing 50 to 70%. Under natural room temperature conditions, it was 5 to 10% for the most entries, except 'Penncross', 'L-93', and 'Penn A-4' cultivars which vigorously produced 20 to 50%. Days to the 50% germination in CB resulted in 4 to 10 DAS under alternative conditions, while 6 to 15 DAS under natural conditions, being 2 to 5 days later than under alternative conditions. Days to the 85% germination were 5.90 to 11.75 DAS under alternative conditions and 7.95 to 12.50 DAS under natural conditions. 'Penn A-1' and 'L-93' were the fastest cultivars under alternative and natural conditions, respectively. Regardless of the temperature conditions, the longest cultivar in germination was 'T-1', being over 11 DAS. In-depth comparative data on germination characteristics and germination patterns among CB cultivars would be usefully applied for a practical CB turf establishment in golf course construction etc.

• Weed & Turfgrass Science
• /
• v.2 no.1
• /
• pp.47-54
• /
• 2013

The study was conducted to investigate early establishment characteristics and germination pattern of fine-textured fescues (FF) under natural room temperature and to analyze differences between alternative and natural conditions for a practical application. Six cultivars from Chewings fescue (CF), creeping red fescue (CRF), hard fescue (HF) and sheep fescue (SF) were evaluated in the study. Daily and cumulative germination pattern were measured and analyzed. Significant differences were greatly observed in germination pattern, days to the first germination, days to 60% germination, and germination percentage with environments, species and cultivars. Final germination rate was 29.7 to 80.0% under natural conditions. The first germination was initiated between 8 and 10 DAS (days after seeding) under natural conditions, being 3 to 4 days later as compared with ISTA conditions. Days to the 60% germination were 12.1 to 19.0 DAS, being 3.0 to 4.2 days slower than that under ISTA conditions. CF 'Jamestown II' was the fastest cultivar, while the slowest CRF 'Audubon'. Turf establishment speed was faster with CRF < SF < HF and < CF in order. Information on differences in germination characteristics and pattern between alternative and natural conditions would be practically useful for a golf course construction etc., when established with FF.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.564-568
• /
• 1998

All elements and systems of electronics have optimum temperature conditions. A using of the thermoelectric method of cooling is the most approach for the thermal management of power electronics. An analysis of using the thermoelectric cooling and the temperature control is given as an efficient method of ensuring a work of power electronic devices in conditions of micro-miniaturization.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.17 no.5
• /
• pp.1-17
• /
• 2014

Research was initiated to investigate early establishment characteristics and germination pattern of Kentucky bluegrass (KB, Poa pratensis L.) under natural room temperature and to analyze differences between alternative and natural conditions for a practical application. Fifteen cultivars of KB were evaluated in the study. Daily and cumulative germination pattern were measured and analyzed on a daily basis. Differences were observed in germination percentage, germination pattern, days to the first germination and days to 75% germination. Germination percentage was variable with cultivars at the end of study. It was 75.75 to 90.25% under natural condition. There were considerable variations in early germination characteristics and germination pattern among KB cultivars according to germination conditions. The first germination in all entries tested was initiated between 6 and 9 DAS (days after seeding) under ISTA (International Seed Testing Association) condition. But it was observed between 9 and 12 DAS under natural condition, being 3 to 5 days later as compared with ISTA condition. On the first date of a germinating process, the germination rate was 0.25% to 25.00% under ISTA condition, while 0.50% to 13.25% under natural condition. Days to the 75% germination were 15.08 to 28.80 DAS under ISTA condition and 17.78 to 28.75 DAS under natural condition. Midnight II, Excursion and Midnight were the fastest cultivars under ISTA condition, while Odyssey the fastest one under natural condition. Regardless of germination condition, the slowest cultivar was Voyager II, being over 4 weeks to 75% germination percentage. For the most cultivars, days to 75% germination under natural room temperature condition were 1 to 8 days slower than under ISTA condition. From this study information on differences in germination characteristics and pattern among cultivars would be usefully applied for KB establishment such as golf course construction. Prior to on-site seeding, a comprehensive germination test is practically recommended due to a possible decline in germination capability during domestic distribution and storage after import.

• Nuclear Engineering and Technology
• /
• v.50 no.2
• /
• pp.268-279
• /
• 2018

The ALCYONE multidimensional fuel performance code codeveloped by the CEA, EDF, and AREVA NP within the PLEIADES software environment models the behavior of fuel rods during irradiation in commercial pressurized water reactors (PWRs), power ramps in experimental reactors, or accidental conditions such as loss of coolant accidents or reactivity-initiated accidents (RIAs). As regards the latter case of transient in particular, ALCYONE is intended to predictively simulate the response of a fuel rod by taking account of mechanisms in a way that models the physics as closely as possible, encompassing all possible stages of the transient as well as various fuel/cladding material types and irradiation conditions of interest. On the way to complying with these objectives, ALCYONE development and validation shall include tests on $PWR-UO_2$ fuel rods with advanced claddings such as M5(R) under "low pressure-low temperature" or "high pressure-high temperature" water coolant conditions. This article first presents ALCYONE V1.4 RIA-related features and modeling. It especially focuses on recent developments dedicated on the one hand to nonsteady water heat and mass transport and on the other hand to the modeling of grain boundary cracking-induced fission gas release and swelling. This article then compares some simulations of RIA transients performed on $UO_2$-M5(R) fuel rods in flowing sodium or stagnant water coolant conditions to the relevant experimental results gained from tests performed in either the French CABRI or the Japanese NSRR nuclear transient reactor facilities. It shows in particular to what extent ALCYONE-starting from base irradiation conditions it itself computes-is currently able to handle both the first stage of the transient, namely the pellet-cladding mechanical interaction phase, and the second stage of the transient, should a boiling crisis occur. Areas of improvement are finally discussed with a view to simulating and analyzing further tests to be performed under prototypical PWR conditions within the CABRI International Program. M5(R) is a trademark or a registered trademark of AREVA NP in the USA or other countries.

• Journal of ILASS-Korea
• /
• v.13 no.2
• /
• pp.65-72
• /
• 2008

It is recognized that alternative fuel such as dimethyl ether (DME) has better combustion polluting characteristics than diesel fuel, even though the cetane number of DME is almost the same as that of diesel. Characteristics of DME spray were observed experimentally under various ambient conditions using a constant volume chamber and a common-rail injection system. N-dodecane and LPG fuel sprays were also observed under same conditions of DME spray. Using spray images from backlight scattering and Mie scattering, characteristics of fuel sprays such as penetration and spray volume were visualized and quantitatively measured. The measurements showed that the penetration of early period decreased remarkably, because evaporation of alternative fuels became prosperous by the influence of flash boiling phenomenon under the condition of the low temperature and pressure compared with n-dodecane. The penetration of DME and LPG spray received the influence of temperature more largely in comparison with low density, because the specific surface area increased by atomizing in high density.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.10
• /
• pp.1172-1177
• /
• 2004

The emission control of automobile has been intensified as a part of the countermeasure to decrease air pollution in the world. As the cars with an alternative fuel starts to get into the spotlight, the cars with low emission has been introduced and exhaust gas regulation forced in this country. These days, LPG vehicles, which infrastructure of fuel was already built up, and CNG vehicles are recognized for alternative fuel cars in this country. In this study, the constant volume combustion chamber was manufactured and used for experiments to obtain the combustion characteristics of propane mixture. The combustion characteristics was analyzed, with the change of supply conditions of propane fuel. Inside the combustion chamber, the maximum temperature increase with the initial pressure is going up. The burning velocity also seems to have the same characteristic as the temperature. However, the heat flux do not change much according to the theoretical correct mixture but it changes with the various initial temperature of the combustion chamber.

• 한국태양에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.259-264
• /
• 2009

Most of the fossil power plants firing lower grade coals are challenged with maintaining good combustion conditions while maximizing generation and minimizing emissions. In many cases significant derate, availability losses and increase in unburned carbon levels can be attributed to poor combustion conditions as a result of poorly controlled local fuel and air distribution within the boiler furnace. The poor combustion conditions are directly related to the gas flow deviation in upper furnace and convection tube-bank but a less reported issue related to in large-scale oppose wall fired boilers. In order to develop a on-line combustion monitoring system and suggest an alternative heat flux estimation method at tube bank, which is very useful information for boiler design tool and blower optimizing system, field test was conducted at operating power boiler. During the field test the exhaust gases' temperature and tube metal temperature were monitored by using a spatially distributed sensors grid which located in the boiler's high temperature vestibule region. At these locations. the flue gas flow is still significantly stratified, and air in-leakage is minimal which enables tracing of poor combustion zones to specific burners and over-fire air ports. Test results showed that the flue gas monitoring method is more proper than metal temperature distribution monitoring for real time combustion monitoring because tube metal temp. distribution monitoring method is related to so many variables such as flue gas, internal flow unbalance, spray etc., Heat flux estimation at the tube bank with flue gas temp. and metal temp. data can be alternative method when tube drilling type sensor can't able to use.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.443-446
• /
• 2009

In this study, a series of degradation test for structural adhesives was performed to investigate the possibility of replacement of the alternative adhesives to the conventional adhesives. Four types of the adhesives were exposed to combined environmental conditions over 1000 hours at an accelerated aging tester, which can simulate natural weather conditions such temperature, moisture and ultraviolet. Mechanical and chemical properties of the adhesives were evaluated through material testing system and FT/IR spectrometer. According to the results, the conventional adhesives can be replaced by the alternative adhesives because the alternative adhesives were more stable to environmental conditions rather than the conventional adhesives.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.11 no.5
• /
• pp.79-91
• /
• 2008

Research was initiated to investigate germination characteristics of creeping bentgrass (CB, Agrostis palustris Huds.). Seven varieties of CB were evaluated with different experiments. An alternative environment condition requiring for a CB germination test by International Seed Testing Association (ISTA) was applied in the Experiment I, consisting of 8-hr light at $25^{\circ}C$ and 16-hr dark at $15^{\circ}C$(ISTA conditions). Experiment II was conducted under a room temperature condition of 5 to $25^{\circ}C$(natural conditions). In each experiment, data such as seed germinating vigor, early germination characteristics, germination speed and germination peak time were measured. Significant differences were observed in seed germinating vigor, early germination characteristics, germination speed and germination peak time. Seed germinating vigor was variable with different environments and varieties. It was 61.50 to 98.25% under ISTA conditions and 55.00 to 98.50% under natural conditions. There were considerable variations in early germination characteristics among CB varieties according to different conditions. Early germination characteristics indicated that all varieties were 1 to 4 days faster in germination under ISTA conditions, when compared with natural conditions. The germination speed, measured as days to seed germination of 70% and 90%, was much faster with Penn A-1, Penn A-4 and Penncross under ISTA conditions. But it was even faster with L-93 and Penncross when grown under natural conditions. Differences were also observed in germination peak time with varieties and growing conditions. It was 0.57 to 2.86 days under ISTA conditions and 0.74 to 1.74 days under natural conditions. Regardless of the environment conditions, the shortest variety was L-93 and the longest one T-1. Considering germinating vigor, early germination characteristics, germination speed and germination peak time, Penn A-1, Penn A-4 and Penncross were regarded as excellent varieties under ISTA conditions in terms of early establishment characteristics, while L-93, Penn A-1 and Penncross under natural conditions. These results suggest that an intensive germination test be needed prior to planting, for the early germinating vigor, germination speed and germination peak time. Also, a proper variety selection and comprehensive site analysis for the growing environmental conditions should be done before golf course construction.