• Journal of Conservation Science
• /
• v.37 no.6
• /
• pp.767-777
• /
• 2021

This study analyzed the microstructures and chemical composition of three samples of bronze mirrors excavated in the Jeollanam-do region, particularly Goheung and Damyang. Under x-ray irradiation, the analysis results confirmed the broken parts and pores caused by cracks, casting, and corrosion. Major and minor elemental analysis were performed on three mirrors by Scanning electron microscopy (SEM) with Energy dispersive x-ray spectrometry (EDS) and Inductively coupled plasma mass spe ctrome try (ICP-MS). The re sult shows that the bronze mirrors containe d Cu-Sn-Pb alloys. Alpha phase and eutectic phase were observed in the microstructure, confirming that the casting was performed without additional heat treatment. Notably, Three bronze mirrors were made early Three Kingdoms period in Korea.

• Korean Chemical Engineering Research
• /
• v.49 no.5
• /
• pp.664-668
• /
• 2011

Spherical alumina precursors represented by $AlO_xCl_y(OH)_z$, 30~200 nm in particle diameter, were prepared by partial hydrolysis of $AlCl_3$ vapor in a 500 ml reactor. Investigated on the particle morphology and size were the effects of the reaction time, the stirring speed and the reaction temperature. The particle morphology and size was insensitive to the reaction time in the range 20 to 300 s. The variation of the stirring speed from 0 to 300 and 800 rpm showed that the particle size was the largest at 0 rpm. As the temperature was varied from 180 to 190, 200, $140^{\circ}C$, the particle size showed a maximum at $190^{\circ}C$. By calcination of the as-produced particles at $1,200^{\circ}C$ for 6h with a heating rate of $10^{\circ}C$/min, ${\alpha}$-alumina particles 45 nm in surface area equivalent diameter were obtained. The particle shape after calcination turned wormlike due to sintering between neighboring particles. A rapid calcination at $1400^{\circ}C$ for 0.5 h with a higher heating rate of $50^{\circ}C$/min reduced the sintering considerably. An addition of $SiCl_4$ or TMCTS(2,4,6,8-tetramethylcyclosiloxane) to the $AlCl_3$ reduced the sintering effectively in the calcination step; however, peaks of ${\gamma}$ or mullite phase appeared. An addition of $AlF_3$ to the particles obtained from the hydrolysis resulted in a hexagonal disc shaped alumina particles.

• Journal of Marine Bioscience and Biotechnology
• /
• v.2 no.3
• /
• pp.174-186
• /
• 2007

Amphora coffeaeformis and Achnanthes longipes are commonly found as dominant benthic microalgae in Jeju coastal water throughout the year. In order to investigate pharmaceutical uses of these diatoms, each single species was isolated with micropipette under phase contrast microscope and subcultured with synthetic seawater media which was enriched with F/2 media, trace metal solution and $Na_2SiO_3$). Growth characteristics of these species were also determined with different combination of salinity, nutrients concentration and temperature. Thereafter, mass culture of each species was done based on the maximum growth condition. Biomass was collected after two weeks of mass culture and freeze dried for antioxidant study. The antioxidant properties of different fractions (n-hexane, chloroform and ethylacetate) obtained by solvent fractionation of 80% methanolic extract of two microalgae were investigated for free radical, reactive oxygen species scavenging (Super oxide, Hydrogen peroxide, Hydroxyl radical and Nitric oxide), metal chelating and lipid peroxidation inhibition activities. All fractions of A. longipes showed higher $DPPH^{\cdot}$ (free radical) scavenging activities (n-hexane: 89.0%, Chloroform: 76.0%, Ethylacetate: 66.0%, Methanol: 90.6% and aqueous residue: 63.0%). N-hexane fraction of A. longipes showed significantly higher activity (49.0%) on nitric-oxide. Ethylacetate fraction of A. longipes and aqueous residue of A. coffeaeformis exhibited 64.0% and 75.6% metal chelating activity which was higher than commercial antioxidants (${\alpha}$-tocopherol: 18.0% and BHT: 16.0%). The n-hexane fraction of A. coffeaeformis had 67.5% activity on $DPPH^{\cdot}$. Chloroform and n-hexane fractions of A. coffeaeformis exhibited 46.2% and 47.6% $H_2O_2$ scavenging effects which were closely similar to commercial antioxidants (${\alpha}$-tocopherol: 49.2% and BHT: 58.6%). Chloroform and ethylacetate fractions of A. longipes and fraction of n-hexane and chloroform of A. coffeaeformis showed better lipid peroxidation activities than ${\alpha}$-tocopherol. These data suggest that both organic and aqueous fractions have good antioxidative compounds with different antioxidant properties.

• Korean Journal of Materials Research
• /
• v.22 no.12
• /
• pp.675-681
• /
• 2012

We aimed to examine the co-doping effects of 1/6 mol% $Mn_3O_4$ and 1/4 mol% $Cr_2O_3$ (Mn:Cr = 1:1) on the reaction, microstructure, and electrical properties, such as the bulk defects and grain boundary properties, of ZnO-$Bi_2O_3-Sb_2O_3$ (ZBS; Sb/Bi = 0.5, 1.0, and 2.0) varistors. The sintering and electrical properties of Mn,Cr-doped ZBS, ZBS(MnCr) varistors were controlled using the Sb/Bi ratio. Pyrochlore ($Zn_2Bi_3Sb_3O_{14}$), ${\alpha}$-spinel ($Zn_7Sb_2O_{12}$), and ${\delta}-Bi_2O_3$ (also ${\beta}-Bi_2O_3$ at Sb/Bi ${\leq}$ 1.0) were detected for all of the systems. Mn and Cr are involved in the development of each phase. Pyrochlore was decomposed and promoted densification at lower temperature on heating in Sb/Bi = 1.0 system by Mn rather than Cr doping. A more homogeneous microstructure was obtained in all systems affected by ${\alpha}$-spinel. In ZBS(MnCr), the varistor characteristics were improved dramatically (non-linear coefficient, ${\alpha}$ = 40~78), and seemed to form ${V_o}^{\cdot}$(0.33 eV) as a dominant defect. From impedance and modulus spectroscopy, the grain boundaries can be seen to have divided into two types, i.e. one is tentatively assigned to ZnO/$Bi_2O_3$ (Mn,Cr)/ZnO (0.64~1.1 eV) and the other is assigned to the ZnO/ZnO (1.0~1.3 eV) homojunction.

• Korean Journal of Materials Research
• /
• v.22 no.12
• /
• pp.682-688
• /
• 2012

In this study we aimed to examine the co-doping effects of 1/6 mol% $Co_3O_4$ and 1/4 mol% $Cr_2O_3$ (Co:Cr = 1:1) on the reaction, microstructure, and electrical properties, such as the bulk defects and the grain boundary properties, of ZnO-$Bi_2O_3-Sb_2O_3$ (ZBS; Sb/Bi = 0.5, 1.0, and 2.0) varistors. The sintering and electrical properties of Co,Cr-doped ZBS, ZBS(CoCr) varistors were controlled using the Sb/Bi ratio. Pyrochlore ($Zn_2Bi_3Sb_3O_{14}$), ${\alpha}$-spinel ($Zn_7Sb_2O_{12}$), and ${\delta}-Bi_2O_3$ were formed in all systems. Pyrochlore was decomposed and promoted densification at lower temperature on heating in Sb/Bi = 1.0 by Cr rather than Co. A more homogeneous microstructure was obtained in all systems affected by ${\alpha}$-spinel. In ZBS(CoCr), the varistor characteristics were improved (non-linear coefficient, ${\alpha}$ = 20~63), and seemed to form ${Zn_i}^{{\cdot}{\cdot}}$(0.20 eV) and ${V_o}^{\cdot}$(0.33 eV) as dominant defects. From impedance and modulus spectroscopy, the grain boundaries were found to be composed of an electrically single barrier (0.94~1.1 eV) that is, however, somewhat sensitive to ambient oxygen with temperature. The phase development, densification, and microstructure were controlled by Cr rather than by Co but the electrical and grain boundary properties were controlled by Co rather than by Cr.

• Membrane Journal
• /
• v.17 no.3
• /
• pp.254-268
• /
• 2007

Sodium type faujasite(FAU) zeolite layers with diverse materials characteristics(Si/Al ratio, thickness, and structural discontinuity) were hydrothermally grown on a porous $\alpha-Al_2O_3$ tube, and then the $CO_2/N_2$ separation was evaluated at $30^{\circ}C$ for an equimolar mixture of $CO_2$ and $N_2$. Among hydrothermal conditions, $SiO_2$ content in hydrothermal solution seriously affected materials characteristics: with an increment in the $SiO_2$ content, Si/Al ratio, thickness, and structural discontinuity of grown FAU zeolite layer simultaneously increased. The present study reveals that structural discontinuity(intercrystalline voids due to an incomplete densification and cracks induced by GIS Na-P1 phase) is the most important variable affecting the $CO_2/N_2$ separation. Also, it was suggested that the $CO_2$ desorption in permeate side be the rate-determining(slowest) step in the overall $CO_2$ permeation.

• Toxicological Research
• /
• v.31 no.3
• /
• pp.255-264
• /
• 2015

Heterocyclic amines (HCAs) and acrylamide are unintended hazardous substances generated by heating or processing of foods and are known as carcinogenic and mutagenic agents by the animal experiments. A simple method was established for a rapid and accurate determination of 12 types of HCAs (IQ, MeIQ, Glu-P-1, Glu-P-2, MeIQx, Trp-P-1, Trp-P-2, PhIP, $A{\alpha}C$, $MeA{\alpha}C$, Harman and Norharman) and acrylamide in three food matrices (non-fat liquid, non-fat solid and fat solid) by isotope dilution liquid chromatography-tandem mass spectrometry (LC-MS/MS). In every sample, a mixture of internal standards including $IQ-d_3$, $MeIQx-d_3$, $PhIP-d_3$, $Trp-P-2-^{13}C_2-^{15}N$ and $MeA{\alpha}C-d_3$ was spiked for quantification of HCAs and $^{13}C_3$-acrylamide was also spiked for the analysis of acrylamide. HCAs and acrylamide in sample were extracted with acetonitrile and water, respectively, and then two solid-phase extraction cartridges, ChemElut: HLB for HCAs and Accucat: HLB for acrylamide, were used for efficiently removing interferences such as pigment, lipid, polar, nonpolar and ionic compounds. Established method was validated in terms of recovery, accuracy, precision, limit of detection, limit of quantitation, and linearity. This method showed good precision (RSD < 20%), accuracy (71.8~119.1%) and recovery (66.0~118.9%). The detection limits were < 3.1 ng/g for all analytes. The correlation coefficients for all the HCAs and acrylamide were > 0.995, showing excellent linearity. These methods for the detection of HCAs and acrylamide by LC-MS/MS were applied to real samples and were successfully used for quantitative monitoring in the total diet study and this can be applied to risk assessment in various food matrices.

• Korean Journal of Materials Research
• /
• v.9 no.4
• /
• pp.428-433
• /
• 1999

An objective of this study is to compare the characteristics of coating layer of plasma sprayed fine $Al_2O_3$ and those of layer by commercial $Al_2O_3$(Metco 105). The microstructure of fine $Al_2O_3$ coating layer was denser compared with commercial $Al_2O_3$ coating layer. The surface roughness$(R_a)$ of the layer by the fine $Al_2$O$_3$ was lower compared with that of commercial $Al_2O_3$. Thickness of splat for fine $Al_2O_3$ was $1.4\mu\textrm{m}$ while the commercial $Al_2O_3$ was $3.53\mu\textrm{m}$. The main phase existing in coating layer was of $\gamma-Al_2O_3$ and the fraction of $\alpha-Al_2O_3$ in fine $Al_2O_3$ coating layer was 8.39% and that of commercial $Al_2O_3$ was 13.79%. Microhardness was no great difference between the fine and commercial $Al_2O_3$ but deviation of the fine $Al_2O_3$ coating layer was relatively large. Accordingly, the strength of splat of the coating was expected that fine $Al_2O_3$was lower than commercial $Al_2O_3$ powder.

• Journal of the Korean Magnetics Society
• /
• v.7 no.3
• /
• pp.140-145
• /
• 1997

The amorphous state of $NdFe_{10.7}TiB_{0.3}$ and its nanocrystallization have been studied by X-ray diffraction, 모스바우어 spectroscopy, and a vibrating sample magnetometer (VSM), $NdFe_{10.7}TiB_{0.3}$ amorphous ribbons were fabricated by a sigle-roll melt-spinning method. The average hyperfine field $H_{hf}$(T) of the amorphous state shows a temperature dependence of $[H_{hf}(T)-H_{hf}(0)]/H_{hf}(0)=-0.46(T/T_c)^{3/2}-0.34(T/T_c)^{5/2}$ for $T/T_c<0.7$ indicative of spin wave excitation. The quadrupole splitting just above the Curie temperature $T_c$ is 0.46 mm/s, whereas the average quadrupole shift below $T_c$ is zero. The Curie and crystallization temperatures are determined to be $T_c$=380K and $T_x=490K$, respectively, for a heating rate of 5 K/min. The occupied area of nanocrystalline phase at around 770K is about 65%. Above the Curie temperature, VSM data show magnetic moments increases again. The formation of $\alpha$-Fe is the main reason for the increasing moment as conformed with the 모스바우어 measurements.

• Food Science of Animal Resources
• /
• v.37 no.6
• /
• pp.940-947
• /
• 2017

Goat milk has a protein composition similar to that of breast milk and contains abundant nutrients, but its use in functional foods is rather limited in comparison to milk from other sources. The aim of this study was to prepare a goat A2 ${\beta}$-casein fraction with improved digestibility and hypoallergenic properties. We investigated the optimal conditions for the separation of A2 ${\beta}$-casein fraction from goat milk by pH adjustment to pH 4.4 and treating the casein suspension with calcium chloride (0.05 M for 1 h at $25^{\circ}C$). Selective reduction of ${\beta}$- lactoglobulin and ${\alpha}_s$-casein was confirmed using sodium dodecyl sulphate-polyacrylamide gel electrophoresis and reverse-phase high-performance liquid chromatography. The hypoallergenic property of A2 ${\beta}$-casein fraction was examined by measuring the release of histamine and tumor necrosis factor alpha from HMC-1 human mast cells exposed to different proteins, including A2 ${\beta}$-casein fraction. There was no significant difference in levels of both indicators between A2 ${\beta}$-casein treatment and the control (no protein treatment). The A2 ${\beta}$-casein fraction is abundant in essential amino acids, especially, branched-chain amino acids (leucine, valine, and isoleucine). The physicochemical properties of A2 ${\beta}$-casein fraction, including protein solubility and viscosity, are similar to those of bovine whole casein which is widely used as a protein source in various foods. Therefore, the goat A2 ${\beta}$-casein fraction may be useful as a food material with good digestibility and hypoallergenic properties for infants, the elderly, and people with metabolic disorders.