• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2001년도 추계학술대회 논문집
• /
• pp.45-49
• /
• 2001

The length and the breadth or a very large floating airport are determined by airplane types and airport facilities. However, the depth affect not only the structural strength but also the functional requirement such as a possibility of taking off and landing. The optimization problem for determining the depth is to select a design so that the cost is minimized. In this paper, a general arrangement and a method to decide the depth are proposed. Strength, functional requirement, and possibility of occurrence of deck wetness and slamming are considered in order to determine the depth of structure. Hydrodynamic forces of the diffraction and radiatin problems are predicted by applying the source-dipole distribution method, and the structural responses are obtained by the finite element method.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.504-509
• /
• 2004

Chemical machining(CHM) is a special process which material removed by contact of strong etchant. The application as industrial process was started from aircraft industry after 2nd world war. Chemical milling, one of the CHM process, initially became commercial bussiness and it was called chem-mill. Even today, this process widely used to remove the material from aircraft wings and fuselage panel in aircraft industry. In this study, it is attempted to design the cylinder pattern which minimize the weight within the allowable stress using chemical milling.

• 한국자동차공학회논문집
• /
• 제4권5호
• /
• pp.9-15
• /
• 1996

A silicon microaccelerometer is designed and fabricated using silicon epitaxial layers for automotive electronic airbag applications. A cantilever structure is chosen for high sensitivity and piezoresistive detection method is adopted for circuit simplicity and low cost. An optimum design is used to find optimum microstructure sizes for maximum sensitivity subject to performance requirements and design constraints on natural frequency, damping ratio, maximum allowable stress and microfabrication limitations. The microaccelerometer is fabricated by micromachining processing steps, composed of material-selective and orientation-dependent chemical etching techniques. Fabricated prototype shows a sensitivity of 88.6$\mu\textrm{V}$/g within a resonant frequency of 1.75KHz. Estimated performance of the microaccelerometer is compared with measured one. Discrepancy between the theoretical values and the experimental values is discussed together with possible sources of the errors.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권3호
• /
• pp.99-105
• /
• 2000

For multi-body dynamic problems. especially coalescent eigenvalue problems with multiobjective optimization, the design sensitivity analysis is too much complicated mathematically and numerically. Therefore, this article proposes a new technique for structural dynamic modification using a mode modification and homologous structures design method with Genetic Algorithm(GA). In this work, the homologous structure of the resiliently mounted multi-body for marine diesel generator systems is studied and the problem is treated as a combinational optimization problem using the GA. In GA formulation, fitness is defined based on penalty function approach. That include homology, allowable stress and minimum weight of common plate.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.626-629
• /
• 1997

In this study, position optimization of insulation rods and suspension rods in discharge electrode frame of electrostatic precipitator(EP) is performed using finite element analysis(FEA). The object of the optimization is to minimize the difference of altitudes in unevenly sagged horizontal structure and to regulate the size of materials within the allowable stress bounds. Uppermost horizontal channel of discharge electrode frame is highly stressed and uniformity of lowest horizontal angle depends on the position of rods. Ten types of frame are analyzed and one recommended model is presented.

• 대한건축학회논문집:구조계
• /
• 제35권3호
• /
• pp.19-25
• /
• 2019

The purpose of this study was to evaluate bending performance of concrete filled soldier pile for temporary retaining wall. Structural performance tests were conducted on total number of four specimens. Each specimen had a unique characteristics with combination of the following variables, existence of reinforcing bar and locations of reinforcing steel plates. The results of this study were as follows; concrete filled steel tubes with being reinforced bar and flange rather than non-bar showed better performance. Higher yield, tensile strength and sufficient plastic strain were archived and maximum moment observed in experiments exceeded theoretical maximum moment in both allowable stress design and limit state design at all specimens.

• 한국항해항만학회지
• /
• 제38권3호
• /
• pp.253-259
• /
• 2014

최근 선박의 대형화 고속화가 진행되면서 항만의 변화와 항내 수역 혼잡의 증대 등 해상 교통에 많은 위험 요소가 늘어가고 있다. 최근 가장 첨예하게 대립되는 것이 항로폭을 적정하게 결정하는 문제이다. 현행의 항로폭 설계법은 해당 수역을 통항하는 최대 선박의 운동 성능을 중심으로 설계되고 있지만, 다양한 종류의 선박이 혼재되어 운항하고 있는 해상교통 환경을 고려하지 않고 있다. 본 연구에서는 항내 수역의 다양한 교통 상황을 설정하고, 교통(용)량을 고려한 항로 설계법을 제안하고 이를 현행 항로설계법과 비교하였다. 이를 위해 기존 항로 설계 방법을 정리하고, 항내 수역을 대상으로 하는 162개의 해상교통 시뮬레이션을 실시하였다. 이 결과를 바탕으로 각 선종별 선형 구성 및 교통량에 따른 환경스트레스값 즉 운항위험도를 추정하였다. 허용 교통량에 대한 적정 항로폭 모델식을 구하고, 실제 수역에 적용하였다. 현행 설계법에 따른 항로폭과 비교하고 그 유용성을 확인하였다.

• 한국지반공학회지:지반
• /
• 제12권3호
• /
• pp.73-82
• /
• 1996

하중과 저항계수 설계론을 채택하는 극한상태 설계 법이 지반공학분야에도 세계적인 추세로 적용되고 있다. 현재의 허용응력설계법은 논란을 거듭하면서 극한상태 설계법으로 교체되리라 전망된다. 최근에 북미와 유럽에서 시방서로 발간되면서 본격적으로 지반공학설계분야에 관심이 되고 있다. 이러한 세계적인 설계이론을 적절히 비교분석함은 장차 한국의 건설여건에 맞도록 적용하는데 기본요건이라 하겠다. 본 논문에서는 극한상태설계 법을 검토하고 말뚝설계에 하중과 저항계수 설계론을 적용하여 분석하고자 한다.

• 한국해양공학회지
• /
• 제24권1호
• /
• pp.153-160
• /
• 2010

This paper deals with the topology optimized design of the riser support structures for floating production storage and offloading units (FPSOs) under global and local loading conditions. For a preliminary study and validation of the numerical approach, a simplified plate under static loading is first evaluated with the representative topology optimization methods, the Homogenization Design Method (HDM) and Density Method (DM) or Simple Isotropic Material with Penalization (SIMP). In the context of the corresponding riser support structures, the design problem is formulated such that structure shapes based on design domain variables are determined by minimizing the compliance subject to a mass target, considering the stress criterion. An initial design model is generated based on an actual FPSO riser support configuration. The topology optimization results present improved design performances under various loading conditions, while staying within the allowable limit of the offshore area.

• 한국해양환경ㆍ에너지학회지
• /
• 제6권2호
• /
• pp.54-62
• /
• 2003

해저배관은 지반쇄굴로 인하여 일부분이 노출되어 자유경간이 형성될 수 있다. 자유경간이 형성되면 환경하중 및 와동유기진동에 의해서 안정성을 잃을 수 있다. 본 연구에서는 해저배관의 안정성을 위협하는 중요 요소인 자유경간의 정적 및 동적 경간을 결정하는 방법을 제시한다. 자유경간 해석에서는 해저배관에 작용하는 압축력 효과를 고려하였으며 토양의 종류에 따라 경계조건을 일반화시켰다. 자유경간 양단의 해저지반은 탄성기초로 간주하였으며, 이들 선형 및 회전 스프링으로 치환하여 경계조건을 일반화시켰다. 정적 및 동적 자유경간의 길이를 산정 할 수 있는 무차원화 된 곡선을 구하였다. 예제해석을 수행하여 그 적용방법을 소개하였다. 본 연구결과는 자유경간을 갖는 해저배관의 설계에 유용하게 적용될 수 있다.