• 한국재료학회지
• /
• 제8권4호
• /
• pp.323-327
• /
• 1998

재충전이 가능한 Li/PEO-$LiClO_{4}$-PC/$LIMn_2O_4$구조의 전고상 전지를 제작하였다. $LIMn_2O_4$박막은 RF 마그네트론 스퍼터링 법으로 제작하였으며, $750^{\circ}C$ 부근에서의 급속열처리를 통하여 스피넬 상으로 결정화시킬 수 있었다. 상온 충.방전 시험을 행한 결과, 평균 전압 4V(vs. Li)의 평탄한 방전 전압과 우수한 재충전 능력을 나타내었다.

• Biotechnology and Bioprocess Engineering:BBE
• /
• 제7권1호
• /
• pp.21-25
• /
• 2002

To maximize and sustain the productivity of Monascus pigments, various environmental and nutritional parameters, such as the initial moisture content, pH, inoculum size, sample size, and nutrient supplement, that influence pigment production were evaluated in solid-state cultures as follows: initial moisture content, $50\%;$ pH, 6.0; inoculum size $1\;\times\;10^4$ spore cells $(grams\;of\;dry\;solid\;substrate)^{-1};$ sample size, 300 g. All supplementary nutrients (carbon, nitrogen, and mineral sources) added has inhibitory effects on the cell growth and red pigment production. In open tray culture the maximum biomass yield and specific productivity of red pigments were 223 mg DCW $(grams\;of\;initial\;dry\;substrate)^{-1}$ and, $47.6\;OD_{500}\;(DCW\;grams)^{-1}h^h{-1}$ respectively.

• Restorative Dentistry and Endodontics
• /
• 제21권1호
• /
• pp.403-424
• /
• 1996

Cell culture methods have been used to assess the cytotoxicity of dental materials. Different paramaters are used to monitor cytotoxic effects. But it is difficult to compare each investigator's results with different methods. The objective of this study was to investigate cytotoxic effect of several retrograde filling materials according to cell lines and assay methods. Cytotoxicity of Bestalloy (Dogmyung, Korea), Prisma APH(Densply International Inc., U.S.A.), Clearfil FII (Kuraray Co., Japan), Fuji II (GC Co., Japan), Fuji II LC (GC Co., Japan) and IRM (Densply Co., U.S.A.) on L929, 3T3 and KB permanent cell lines was measured. Radiochromium, Lactate dehydrogenase (LDH) release method and colorimetric assays, namely neutral red (NR) and MTT were used. Each material was mixed according to the manufacturer's instruction. They were tested as solid and extracted state. Cell culture media were added to each mixed or solid materials then the solution was collected and used as extract solutions. Solid Fuji II showed mild cytotoxicity on three cell lines using radiochromium release method. There was no difference in cytotoxicity of extract solution group using radiochromium release method. In colorimetric assay immediate Fuji II group and all the IRM groups showed severe cytotoxic effect. Difference in cyctotoxicity was due to rather kinds of cell lines than assay methods. Solid Fuji II and IRM showed mild cytotoxicity on three cell lines. But extract solutions had different cytotoxic effect according to cell lines using LDH release assay. Light-cured glass ionomer had mild to moderate degree of cytotoxicity on three cell lines. Cytotoxicity was affected by specimen prepaton. Susceptibility of each cell ines were also affected by assay emthods. It was suggested that cytotoxicity study using only one cell line and/or assay method might not accurately reflect the real toxic nature of dental biomaterials.

• Journal of Pharmaceutical Investigation
• /
• 제31권3호
• /
• pp.167-172
• /
• 2001

All-trans retinoic acid (ATRA), vitamin A acid, has been shown to exert anticancer activity in a number of types of cancers, particularly in acute promyelocytic leukaemia (APL). Due to its highly variable bioavailability and induction of its own metabolism after oral treatment, development of parenteral dosage forms are required. However, its poor aqueous solubility and chemical unstability give major drawbacks in parenteral administration. This study was undertaken to investigate a possibility to develop a parenteral formulation of ATRA by employing solid lipid nanoparticle (SLN) as a carrier. By optimizing the production parameters and the composition of SLNs, SLNs with desired mean particle size (<100 nm) as a parenteral dosage form could be produced from trimyristin (as solid lipid), Egg phosphatidylcholine and Tween 80 (as SLN stabilizer). The mean particle size of SLN formulation of ATRA was not changed during storage, suggesting its physical stability. Thermal analysis confirmed that the inner lipid core of SLNs exist at solid state. The mean particle size of ATRA-loaded SLNs was not significantly changed by the lyophilization process. ATRA could be efficiently loaded in SLNs, while maintaining its anticancer activity against HL-60, a well-known APL cell line. Furthermore, by lyophilization, ATRA loaded in SLN could be retained chemically stable during storage. Taken together, our present study demonstrates that physically and chemically stable ATRA formulation adequate for parenteral administration could be obtained by employing SLN technology.

• Journal of Power Electronics
• /
• 제19권2호
• /
• pp.487-496
• /
• 2019

For a solid-state transformer (SST), some factors, such as signal delay, switching loss and differences in the system parameters, lead to unbalanced DC-link voltages among the cascaded H-bridges (CHB). With a control method implemented in the ${\alpha}{\beta}$ frame, the DC-link voltages are balanced, and the reactive power is equally distributed among all of the H-bridges. Based on the ${\alpha}{\beta}$ frame control, the system can achieve independent active current and reactive current control. In addition, the control method of the high-voltage stage is easy to implement without decoupling or a phase-locked loop. Furthermore, the method can eliminate additional current delays during transients and get the dynamic response rapidly without an imaginary current component. In order to carry out the controller design, the vector refactoring relations that are used to balance DC-link voltages are derived. Different strategies are discussed and simulated under the unbalanced load condition. Finally, a three-cell CHB rectifier is constructed to conduct further research, and the steady and transient experimental results verify the effectiveness and correctness of the proposed method.

• 한국표면공학회지
• /
• 제51권4호
• /
• pp.243-248
• /
• 2018

All solid state thin film batteries with two types of cell structure, Pt / $LiCoO_2$ / LiPON / Cu and Pt / $LiCoO_2$ / LiPON / $LiCoO_2$ / Cu, are prepared and their electrochemical performances are investigated to evaluate the effect of $LiCoO_2$ interlayer at the interface of LiPON / Cu. The crystallinity of the deposited $LiCoO_2$ thin films is confirmed by XRD and Raman analysis. The crystalline $LiCoO_2$ cathode thin film is obtained and $LiCoO_2$ as the interlayer appears to be amorphous. The surface morphology of Cu current collector after cycling of the batteries is observed by AFM. The presence of a 10 nm-thick layer of $LiCoO_2$ at the interface of LiPON / Cu enhances the interfacial adhesion and reduces the interfacial resistance. As a result, Li plating / stripping at the interface of LiPON / Cu during charge/discharge reaction takes place more uniformly on Cu current collector, while without the interlayer of $LiCoO_2$ at the interface of LiPON / Cu, the Li plating / stripping is localized on current collector. The thin film batteries with the interlayer of $LiCoO_2$ at the interface of LiPON / Cu exhibits enhanced initial coulombic efficiency, reversible capacity and cycling stability. The thickness of the anode current collector Cu also appears to be crucial for electrochemical performances of all solid state thin film batteries.

• 전기화학회지
• /
• 제3권2호
• /
• pp.115-120
• /
• 2000

양극 물질로 산화바나듐 박막, 고체전해질로는 LiPON 박막 그리고 음극 물질로는 리튬 금속 박막을 선택하여 $Li/LiPON/V_2O_5/Pt$ 구조의 전고상 박막 전지를 제작하였고 전지 특성을 평가하였다. 산화바나듐 박막은 여러 산소 분압에서 직류 반응성 스퍼터링으로 증착하여 전기화학적 특성을 분석한 결과 $20\%\;O_2/Ar$비에서 가장 우수한 가역 특성을 나타내었다. 직류 반응성 스퍼터링에 의해 산화바나듐 박막을 제작한 후 진공을 그대로 유지한 상태에서 r.f. 반응성 스퍼터링에 의해 LiPON 고체전해질 박막을 증착하였다. 그 후 dry room내에서 진공 열증착법에 의해 리튬 금속 박막을 증착하여 전고상의 박막 전지를 제작하였다. $Li/LiPON/V_2O_5$ 박막 전지를 전압 범위와 전류 밀도를 변화시켜 충방전 시험을 행한 결과 $7{\mu}A/cm^2$의 전류 밀도와 3.6-2.7 V의 전압범위에서 가장 우수한 가역 특성을 나타내었다. $Li/LiPON/V_2O_5$박막 전지로 초시계를 구동 시켰으며 이는 in-situ공정에 의해 제작된 박막 전지가 소자 에너지원으로의 응용 가능성을 보여 주었다.

• Journal of Power Electronics
• /
• 제9권3호
• /
• pp.472-480
• /
• 2009

In this paper, a charge equalization converter with parallel-connected primary windings of transformers is proposed. The proposed work effectively balances the voltage among Lithium-Ion battery cells despite each battery cell has low voltage gap compared with its state of charge (SOC). The principle of the proposed work is that the equalizing energy from all battery strings moves to the lowest voltage battery through the isolated dc/dc converter controlled by the corresponding solid state relay switch. For this research a prototype of four Lithium-Ion battery cells is optimally designed and implemented, and experimental results show that the proposed method has excellent cell balancing performance.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.163-166
• /
• 1997

Aluminium foam material is a highly porous material having complicated cellular structure defined by randomly distributed air pores in metallic matrix. this structure gives the aluminium a set of properties which cannot be achieved by any of conventional treatments. The properties of aluminium foam material significantly depend on its porosity, so that a desired profile of properties can be tailored by changing the foam density. Melting method is the one of foaming processes, which the production has long been considered difficult to realize becaues of such problems as the low foamability of molten metal, the varying size of. cellular structures, solidification shrinkage and so on. These problems, however, have gradually been solved by researchers and some manufacturers are now producing foamed aluminum by their own methods. Most of all, the parameters of solving problem in electric furnace were stirring temperature, stirring velocity, foaming temper:iture, and so on. But it has not considered about those in induction heating, foaming velocity and foaming temperature in semi-solid state yet. Therefore, this paper presents the effects on these parameter to control cell size, quantity and distribution.

• 한국주조공학회지
• /
• 제21권4호
• /
• pp.253-259
• /
• 2001

There are many methods to produce metal foams, which can be classified into three groups according to the state of the starting metal i.e. liquid or powder or solid. Three types of defects such as cell closing, cell deformation or breakdown and cell misrun are thought to be occurred when we make the open cell aluminum foams by precision casting. Filling ability of the mold slurry between preform is related with cell closing, mold collapsibility is related with cell deformation or breakdown, mold temperature and pouring pressure are related with cell misrun. These factors can be evaluated by measuring slurry fluidity, burnout strength and permeability of the mold. Properties of the plaster mold were evaluated to find optimum mold conditions for high quality open cell aluminum foam in this study. Permeability was almost zero independent of burnout conditions, however, crack initiation was found on the surface of all specimens one or two minutes after taking out from the furnace. Crack has grown and disappeared with time. This crack may facilitate the mold filling when molten metal is poured, because of the improved mold permeability. It was considered that crack initiation and disappearance was closely related with temperature difference between the surface and inner part. Knocking-out the mold is a difficult problem due to the small cell size, because continuous mesh structure of the metal foam is not strong. It is not easy to remove molding material after pouring. We can expect that water quenching can facilitate the knocking-out the mold after solidification without damaging cell structures. Collapsed particles after water quenching became bigger with the increase in time.