• Journal of the Korean Wood Science and Technology
• /
• v.20 no.1
• /
• pp.15-22
• /
• 1992

This study was performed to investigate the corrosion of metal fasteners in waterborne preservative-treated wood. Of all the metal tested, steel exhibited the greatest amount of corrosion across all preservatives and exposure conditions whereas stainless steel was totally inert. Galvanized steel corroded at a much lower rate compared to steel and the corrosion of brass was negligible. Among the preservatives, CCA-Type B was the most corrosive system tested. The sequence for the average corrosivity across all metals was: CCA-type B>CCA-Type C${\geq}$ACC${\geq}$CCA-Type A. Across all metals and retentions the salt formulations were more corrosive than the oxide and the corrosion was increased with the increse in the amount of preservative loadings. The amount of corrosion was also increased with the increase in exposure relative humidity (RH) across all metals and presevatives However, at the 60% RH exposure condition, the corrosion of metals was very negligible. Consequently, it can be concluded that across all metals oxide-type preservatives should be used to prevent the corrosion problem of metal fasteners in contact with treated wood and the use of steel nail preservative-treated wood should be avoided without distinction of end-use location, i.e., exterior or interior, and the use of stainless steel or at least brass nail in damp exterior condition was strongly recommended.

• The Journal of Advanced Prosthodontics
• /
• v.2 no.4
• /
• pp.134-141
• /
• 2010

PURPOSE. The objective of this study was to evaluate fracture strength of collarless metal-ceramic FPDs according to their metal coping designs. MATERIALS AND METHODS. Four different facial margin design groups were investigated. Group A was a coping with a thin facial metal collar, group B was a collarless coping with its facial metal to the shoulder, group C was a collarless coping with its facial metal 1 mm short of the shoulder, and group D was a collarless coping with its facial metal 2 mm short of the shoulder. Fifteen 3-unit collarless metal-ceramic FPDs were fabricated in each group. Finished FPDs were cemented to PBT (Polybutylene terephthalate) dies with resin cement. The fracture strength test was carried out using universal testing machine (Instron 4465, Instron Co., Norwood MA, USA) at a cross head speed of 0.5 mm/min. Aluminum foil folded to about 1 mm of thickness was inserted between the plunger tip and the incisal edge of the pontic. Vertical load was applied until catastrophic porcelain fracture occurred. RESULTS. The greater the bulk of unsupported facial shoulder porcelain was, the lower the fracture strength became. However, there were no significant differences between experimental groups (P > .05). CONCLUSION. All groups of collarless metal-ceramic FPDs had higher fracture strength than maximum incisive biting force. Modified collarless metal-ceramic FPD can be an alternative to all-ceramic FPDs in clinical situations.

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.3
• /
• pp.295-302
• /
• 2007

Statement of problem. Fracture of the tooth-colored superstructure material is one of the main prosthetic complications in implant-supported prostheses. Purpose. The purpose of this in vitro study was to compare the fracture strength between the cement-retained implant-supported metal-ceramic crowns and the indirect composite resinveneered metal crowns under the vertical compressive load. Material and methods. Standard implants of external type (AVANA IFR 415 Pre-mount; Osstem Co., Busan, Korea) were embedded in stainless steel blocks perpendicular to their long axis. Customized abutments were fabricated using plastic UCLA abutments (Esthetic plastic cylinder; Osstem Co., Busan, Korea). Thirty standardized copings were cast with non-precious metal (Rexillium III, Pentron, Walling ford, Conn., USA). Copings were divided into two groups of 15 specimens each (n = 15). For Group I specimens, metal-ceramic crowns were fabricated. For Group II specimens, composite resin-veneered (Sinfony, 3M-ESPE, St. Paul, MN, USA) metal crowns (Sinfony-veneered crowns) were fabricated according to manufacturer's instructions. All crowns were temporary cemented and vertically loaded with an Instron universal testing machine (Instron 3366, Instron Corp., Norwood, MA, USA). The maximum load value (N) at the moment of complete failure was recorded and all data were statistically analyzed by independent sample t-test at the significance level of 0.05. The modes of failure were also investigated with visual analysis. Results. The fracture strength of Sinfony-veneered crowns ($2292.7{\pm}576.0N$) was significantly greater than that of metal-ceramic crowns ($1150.6{\pm}268.2N$) (P < 0.05). With regard to the failure mode, Sinfony-veneered crowns exhibited adhesive failure, while metal-ceramic crowns tended to fracture in a manner that resulted in combined failure. Conclusion. Sinfony-veneered crowns demonstrated a significantly higher fracture strength than that of metal-ceramic crowns in cement-retained implant-supported prostheses.

• The Journal of Korean Academy of Prosthodontics
• /
• v.53 no.4
• /
• pp.295-300
• /
• 2015

Purpose: The aim of this study was to evaluate the shear bond strength between Ni-Cr alloy and composite resin using universal adhesive systems coMPared to conventional method using metal primers. Materials and methods: For this study, a total of 120 cast commercial Ni-Cr alloy (Vera Bond 2V) disks were embedded in acrylic resin, and their surfaces were smoothed with silicon carbide papers and airborne-particle abrasion. Specimens of each metal were divided into 6 groups based on the combination of metal primers (Metal primer II, Alloy primer, Metal & Zirconia primer, MKZ primer) and universal adhesive systems (Single Bond Universal, All Bond Universal). All specimens were stored in distilled water at $37^{\circ}C$ for 24 hours. Shear bond strength testing was performed with a universal testing machine at a cross head speed of 1 m/min. Data (MPa) were analyzed using one-way ANOVA and the post hoc Tukey's multiple comparison test (${\alpha}$=.05). Results: There were significant differences between Single Bond Universal, All Bond Universal, Metal Primer II and Alloy Primer, MKZ Primer, Metal & Zirconia Primer (P<.001). Conclusion: Universal Adhesive system groups indicated high shear bond strength value bonded to Ni-Cr alloy than that of conventional system groups using primers except Metal Primer II. Within the limitations of this study, improvement of universal adhesive systems which can be applied to all types of restorations is recommended especially non-precious metal alloy. More research is needed to evaluate the effect of silane inclusion or exclusion in universal adhesive systems.

• Tribology and Lubricants
• /
• v.29 no.4
• /
• pp.235-241
• /
• 2013

The tribological characteristics of dental metal alloys and zirconia were studied by carrying out a friction and wear performance test. In this study, a pin-on-disk-type tester was used and dead weight was employed as the normal load applied to the test specimen. The friction coefficient of dental metal alloys was investigated in terms of their weight and sliding velocity. Microscopic observations were carried out on worn surfaces of specimens. The results indicated that among all metal alloys, Super-A had the highest friction coefficient. Super-A had the lowest amount of wear among all metal alloys, and the amount of wear increased in the following order: Crown & Bridge, Porcelain, and Partial. Crown & Bridge had the best friction coefficient, but the hardness of Crown & Bridge was lower than that of Porcelain and Partial. Experimental measurement results indicated that the disk weight before and after the experiment was the same.

• The Bulletin of The Korean Astronomical Society
• /
• v.36 no.2
• /
• pp.70.2-70.2
• /
• 2011

We present a study of the metallicities, ages, and alpha-elements of globular clusters (GCs) in nearby giant elliptical galaxies (gEs) (M87, M49, M60, NGC 5128, NGC 1399, NGC 1407, and NGC 4636) using data in the literature. We used only the data for the GCs derived from the comparison of absorption line indices with the single stellar population model. The metallicity distributions of GCs in these gEs are bimodal, showing the existence of metal-poor and metal-rich populations. All these gEs harbor young GCs with ages less than 5 Gyr as well as old GCs. The mean age of the metal-rich GCs ([Fe/H]>-0.9) is about 3 Gyr younger than that of the metal-poor GCs. The mean values for the alpha-elements of the GCs are smaller than or similar to that of the Milky Way GCs. All the GCs in these gEs show an age-metallicity relation; the larger the metallicities of the GCs are, the younger the GCs are. Old GCs with ages > 10 Gyr have two distinct sub-populations (metal poor and metal rich), while young GCs show a broad metallicity distribution with a single peak. We discuss these results in relation with the formation of GCs in gEs.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.6
• /
• pp.744-752
• /
• 2007

Recently a fuel oil of the diesel engine in the ship is being changed with low quality as the oil price is higher more and more. Therefore the wear and corrosion in all parts of the engine like cylinder liner ring groove of piston crown, spindle and seat ring of exhaust valve are increased with using of heavy oil of low quality In particular the degree of wear and corrosion in between valve spindle and seat ring are more serious compared to the other parts of the engine due to operating in severe environment such as the high temperature of exhaust gas and repeating impact. Thus the repair weld to the valve spindle and seat ring is a unique method to prolong the life of the exhaust valve in an economical point of view In this study. corrosion property of both weld metal zone and base metal was investigated with some electrochemical methods such as measurement of corrosion potential, cathodic and anodic polarization curves, cyclic voltammogram and polarization resistance etc. in 5% $H_2SO_4$ solution. in the case of being welded with some welding methods and welding materials to the exhaust valve specimen as the base metal. In all cases. the values of hardness of the weld metal zone were more high than that of the base metal. And their corrosion resistance were also superior to the base metal. The weld metal of A2F(AC SMAW: 2 pass welding with foreign electrode) showed a relatively good results to the corrosion resistance as well as the hardness compared to the ether welding methods and welding materials. Moreover it indicated that hardness of the weld metal by the domestic electrode was considerably high compared to that of the foreign electrode.

• Proceedings of the KIPE Conference
• /
• 2019.11a
• /
• pp.160-161
• /
• 2019

본 논문에서는 Si-MOSFET 및 GaN-HEMT 기반 All Metal Induction Cooktop의 고효율 동작을 위한 공진네트워크 설계 및 운전주파수영역을 제시한다. 이를 위해 워킹 코일과 용기의 등가 파라미터를 바탕으로 동작 주파수에 따른 공진 네트워크를 각각 설계한다. 또한 시뮬레이션 및 수학적 계산을 통해 설계된 시스템의 주파수 조건 별 손실 비교를 통해 각 스위칭 소자에 따른 적합한 공진네트워크 설계방안을 제시한다.

• Proceedings of the KIPE Conference
• /
• 2017.07a
• /
• pp.46-47
• /
• 2017

본 논문에서는 All Metal 용기 가열을 위한 자성체 및 비자성체 용기 판별 제어 알고리즘을 설계한다. 용기 재질과 위치에 따른 파라미터를 분석 후 부하 모델링을 통해 동작 전 용기재질 감지 및 동작 중 용기 사라짐 감지 등을 수행한다. 또한 용기 이외의 숟가락과 같은 물체 판별법을 분석하고 실험을 통해 설계된 알고리즘을 검증한다.

• Asian Journal of Turfgrass Science
• /
• v.11 no.3
• /
• pp.205-210
• /
• 1997

The metal spikes evaluated in this study significantly affected more negative on the turf wear and ball speed of putting green than alternative plastic spikes. 1.The metal spikes caused the most amount of wear compared with plastic spikes, athletic shoes and mountain-climbing shoes. On the other hand, athletic shoes caused the least amount of wear. Plastic spikes caused wear more than athletic shoes, hut apparently wear less than metal spikes. The wear from metal spike repaired later than any other tread types. 2.The wear from all kinds of shoe treads in wetcondition green were higher than in dry-condition green and the wear from metal spikes was more severe compared with plastic spikes in both green condition. 3. Ball speed of heavy compaction area by metal spike was reduced about 9% compared with that of light compaction area, hecause metal spikes made many holes in the putting green surface. On the other hand, plastic spikes did not affect hall speed of heavy and light compaction area in the putting green. Key words: Metal spike, Plastic spike, Wear, Ball speed.