• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 D
• /
• pp.1913-1914
• /
• 2006

Modem Industrial control systems tend to adopt a variety of intelligent wireless device controllers to interface front-end computers with active components of the industrial device. Some of the intelligent control systems come equipped with a wireless SMS(Simple Message Service) interface giving an opportunity to use fault alarm Interlock system. Immediately send warning or alert messages to Mobile devices or remote users. Real time monitoring the SMS systems by Mobile devices. Control systems remotely by mobile devices in emergency situation. In order to provide against system fault, SMS Mobile System will enable system administrator to promptly access, monitor and control the system whenever users want and wherever users are, by utilizing wireless Internet and mobile devices. This paper presents the Mobile SMS system for PAL Control System.

• 한국정보통신설비학회:학술대회논문집
• /
• 한국정보통신설비학회 2009년도 정보통신설비 학술대회
• /
• pp.127-130
• /
• 2009

We propose a method for detecting DDoS (Distributed Denial of Service) traffic in real-time inside the backbone network. For this purpose, we borrow the concepts of MACD (Moving Average Convergence Divergence) and RoC (Rate of Change), which are used for technical analysis in the stock market Due to the fact that the method is based on a quantitative, rather than a heuristic, detection level, DDoS traffic can be detected with greater accuracy (by reducing the false alarm ratio). Through simulation results, we show how the detection level is determined and demonstrate how much the accuracy of detection is enhanced.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 F
• /
• pp.2590-2593
• /
• 1999

This paper describes the development of Emergency Generator Equipments Diagnosis System for monitoring generator equipments and battery system. This system is capable of measuring on up to 20 separate sites of generator, engine and periphral equipment's. Battery system also capable of measure the setting time, float and discharge voltage of up to 240 cells in a single installation, and has the memory capacity to store battery's alarm data information on up to 200 separate sites. This system are easy to maintain and attain cost effectively, so that prepared for meeting the customer's service needs immediately. The system is additionally programmed with a each model, that will enable to accurately determine the generator equipments and remain battery capacity in a system following a short discharge test. It is also equipped with remote interrogation and control facilities.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2002년도 추계 학술발표회 논문집
• /
• pp.51-60
• /
• 2002

In this study we developed the visualization scheme of spatial ground-motion measurements in real time by using DSS data. Even though this scheme itself is useful for national earthquake mitigation plans, this scheme could be served as the crucial core for constructing rapid earthquake damage evaluation system. DSS is the abbreviation of Data Subscription Service and this is the pre-assigned request for the seismic stations to send very limited brief data with high priority and negligible transmission load. In addition to visualize the damage area with intensity, the corresponding epicenter can be estimated roughly for quick event alarm. For the interpolation of spatially irregular PGA data, the program, named as surface. of GMT was used with NetCDF grid file format. Since the grid file is similar to a postscript file, the program, called as shading, was coded with C language by using Matpak library in order to convert grid files into image files.

• 한국정밀공학회지
• /
• 제15권1호
• /
• pp.19-25
• /
• 1998

Remote fault diagnosis and maintenance system using general telecommunication network is necessary for an effective fault diagnosis and higher productivity of NC machine tools. In order to monitor machine tool condition and diagnose alarm states due to electrical and mechanical faults, a remote data communication system for monitoring of NC machine fault diagnosis and status is developed. The developed system consists of (1) remote communication module among NC's and host PC using PSTN. (2) 8 channels analog data sensing module, (3) digital I/O module for control or NC machine, (4) communication module between NC machine and remote data communication system via RS-232C, and (5) software man-machine interface. Diagnostic monitoring results generated through a successive type inference engine are displayed in user-friendly graphics. The validity and reliability of the developed system is verified to be a powerful commercial version on a vertical machining center through a series of experiments.

• 한국정보통신설비학회:학술대회논문집
• /
• 한국정보통신설비학회 2006년도 하계학술대회
• /
• pp.91-94
• /
• 2006

In this paper, we deployed the tunnel inspection and monitoring system by wireless sensor network. It is shown that the wireless sensor network which is composed of sensor, wireless communication module, and gateway system can be applied to tunnel monitoring system. Sensors included herein are acceleration transducers, fire-alarm sensors, water-level sensors, and magnetic contact sensors. It is also found that the wireless sensor network can deliver sensing data reliably by ad-hoc networking technology. The gateway system that can send the sensing data to server by CDMA (code division multiple access) is developed. Finally, monitoring system is constructed by web service technology, and it is observed that this system can monitor the present state of tunnel without difficulties. Furthermore, the above system provides an alternative to inspect and monitor the tunnel efficiently where the conventional wired system cannot be applied.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 F
• /
• pp.2156-2159
• /
• 1998

This paper describes a Battery Checking & Monitoring System for monitoring battery cell and power system in Uninterruptible Power Supplies(UPS). The system is capable of measuring, in a matter of setting time, float and discharge voltage of up to 240 cells in a single installation, and has the memory capacity to store battery's alarm data information on up to 200 separate sites. This system are easy to maintain and attain cost effectively, so that prepared for meeting the customer's service needs immediately. The system is additionally programmed with a each model, that will enable to accurately determine the remain battery capacity in a UPS system following a short discharge test. It is also equipped with remote interrogation and control facilities.

• 음성과학
• /
• 제8권4호
• /
• pp.59-72
• /
• 2001

In this paper, we experimented with speaker change detection that uses a statistical method for NOD (News On Demand) service. A specified speaker's change can find out content of each data in speech if analysed because it means change of data contents in news data. Speaker change detection acts as preprocessor that divide input speech by speaker. This is an important preprocessor phase for speaker tracking. We detected speaker change using GLR(generalized likelihood ratio) distance base division and BIC (Bayesian information criterion) base division among matrix method. An experiment verified speaker change point using BIC base division after divide by speaker unit using GLR distance base method first. In the experimental result, FAR (False Alarm Rate) was 63.29 in high noise environment and FAR was 54.28 in low noise environment in MDR (Missed Detection Rate) 15% neighborhood.

• 한국정보처리학회:학술대회논문집
• /
• 한국정보처리학회 2013년도 추계학술발표대회
• /
• pp.336-338
• /
• 2013

본 논문에서는 도착예정지를 지나치고, 버스노선 안내 시스템과 지하철 노선 안내 시스템이 서로 분리되어 있어 지하철에서 버스로 환승하거나 그 반대의 경우에 시스템 사용에 있어 번거로운 문제점을 개선하기 위해 LBS 기반 도착예정지 알람 서비스 시스템을 설계하였다. 이를 위하여 Open API와 LBS를 분석하고, 도착예정지를 지나치지 않도록 하기 위해 LBS를 이용하여 도착예정지 알람 서비스 시스템을 설계하였다.

• 한국IT서비스학회지
• /
• 제22권3호
• /
• pp.85-100
• /
• 2023

The development of Airside Vehicle Control System(AVCS) at Gimpo Airport aims to reduce ground safety accidents in movement area and improve airport operation efficiency and safety management service quality. The vehicle is controlled by a brake controller RTK-antenna and On-Board Diagonostics(OBD) module. Location data is transmitted to a nearby communication base station through a Wi-Fi router and the base station is connected to the AVCS by an optical cable to transmit location data from each vehicle. The vehicle position is precisely corrected to display information using the system. The system allows airport operators to view registered information on aircraft and vehicles and monitor their locations speeds and directions in real time. When a vehicle approaches a dangerous area alarm warnings and remote brake control are possible to prevent accidents caused by carelessness of the driver in advance.