• 한국분말재료학회지
• /
• 제11권2호
• /
• pp.171-178
• /
• 2004

Effects of liquid phase and reinforcing particle morphology on the sintering of Al-6 wt％Cu-10 vol％ $Al_2O_3$ or SiC particles were studied in regards to densification, structure and transverse rupture properties. The Al-Cu liquid phase penetrated the boundaries between the aluminum matrix powders and the interfaces with reinforcing particles as well, indicating a good wettability to the powders. This enhanced the densification during sintering and the resulting strength and ductility. Since most of the copper added, however, was dissolved in the liquid phase and formed a brittle $CuAl_2$ phase upon cooling rather than alloyed with the aluminum matrix, the strengthening effect by the copper was not fully realized. Reinforcing particles of agglomerate type were found less suitable for the liquid phase sintering than solid type particles. $Al_2O_3$ and SiC particles protluced little difference on the sintering behavior but their size had a large effect. Repressing of the sintered composites increased density and bending properties but caused debonding at the matrix-particle interfaces and also fracturing of the particles.

• 반도체디스플레이기술학회지
• /
• 제20권1호
• /
• pp.12-17
• /
• 2021

The electronic and magnetic properties for Mn-adsorbed on the chalcopyrite (CH) AlGaP2 semiconductor are investigated by using first-principles FPLMTO method. The clean CH-AlGaP2 without adsorbed Mn is a p-type semiconductor with a direct band-gap. The Mn-adsorbed CH-AlGaP2 exhibits the ferromagnetic state. It is more energetically stable than the other magnetic ones. The interstitial site on P-terminated surface is more energetically favorable one than the Al/Ga-terminated surface, or the other adsorbing sites. In the case of Mn-adsorbed Al/Ga-terminated surface, it is induced a strong coupling between Mn-3d and neighboring P-3p electrons. The holes of partially unoccupied minority Mn-3d state and majority (or minority) Al-3p or P-3p state are induced. Thus a high magnetic moment of Mn is sustained by holes-mediated double-exchange coupling. It is noticeable that the semiconducting and half-metallic characteristics of CH-AlGaP2:Mn thin film is disappeared.

• 한국재료학회지
• /
• 제26권11호
• /
• pp.628-634
• /
• 2016

The cold rolling workability and mechanical properties of two new alloys, designed and cast Al-5.5Mg-2.9Si and Al-7Mg-0.9Zn alloys, were investigated in detail. The two alloy sheets of 4 mm thickness, 30 mm width and 100 mm length were reduced to a thickness of 1 mm by multi-pass rolling at ambient temperature. The rolling workability was better for the Al-7Mg-0.9Zn alloy than for the Al-5.5Mg-2.9Si alloy; in case of the former alloy, edge cracks began to occur at 50% rolling reduction, and their number and length increased with rolling reduction; however, in the latter alloy, the sheets did not have any cracks even at higher rolling reduction. The mechanical properties of tensile strength and elongation were also better in the Al-7Mg-0.9Zn alloy than in Al-5.5Mg-2.9Si alloy. Work hardening ability after cold rolling was also higher in the Al-7Mg-0.9Zn alloy than in the Al-5.5Mg-2.9Si alloy. At the same time, the texture development was very similar for both alloys; typical rolling texture developed in both alloys. These differences in the two alloys can primarily be explained by the existence of precipitates of $Mg_2Si$. It is concluded that the Al-7Mg-0.9Zn alloy is better than the Al-5.5Mg-2.9Si alloy in terms of mechanical properties.

• 한국주조공학회지
• /
• 제24권6호
• /
• pp.340-346
• /
• 2004

초정 $Mg_2Si$와 미세한 $MgZn_2$ 석출상을 갖는 고강도 내마모 Al합금을 개발하기 이하여 Al-l2wt%Mg-5.5wt%Zn합금에 0-5wt%까지 Si을 첨가 시켰으며, 미세조직 및 기계적 성질에 미치는 영향을 조사하였다. Si의 함량이 증가함에 따라 형성되는 $Mg_2Si$상의 양이 증가하였으며, 동시에 고강선 온도가 점차적으로 증가함에 따라 효과적인 열처리가 가능해지는 것을 관찰할 수 있었다. 5wt%Si이 첨가된 합금의 경우 적절한 열처리를 통해 미세한 $MgZn_2$ 석출상이 기지에 균일하게 분포한 미세조직을 얻을 수 있었고 이를 통해 인장강도를 현저하게 증가시킬 수 있었다. 또한 Si이 첨가된 Al-Mg-Zn합금은 유동도 및 열간 균열저항성과 같은 주조성면에서도 다른 고강도 Al합금에 비하여 월등히 우수한 것으로 나타났다.

• 한국결정성장학회지
• /
• 제16권3호
• /
• pp.116-120
• /
• 2006

반도체 드라이 에처 시스템의 웨이퍼 정전기 척에 적용하기 위해 플라즈마 스프레이 방법으로 Al-60 계열 기판에 코팅한 $Al_2O_3$ 코팅 막의 특성을 조사하였다. 시편 뒷면에 냉각봉이 장착되었을 때와 없을 때, 용사거리와 분말공급량을 변형하면서 $Al_2O_3$ 막 코팅을 하여 시편을 제작 하였다. 시편 뒷면에 냉각봉이 없을 때는 크랙과 기공이 많이 발생하였다. 시편 뒷면에 냉각봉을 장착하고 분말공급량을 15g/min로 한 경우에 용사거리 60, 70, 80mm에 따른 $Al_2O_3$ 코팅에서는 크랙과 기공은 거의 찾아볼 수 없었다. 용사거리 변화에 따른 $Al_2O_3$ 막 코팅의 표면형태 변화는 없었다. 같은 공정조건에서 분말 공급량을 20g/min로 한 경우에도 크랙은 볼 수 없었으나 약간의 기공이 생겼고, 분말공급량을15g/min로 하였을 때 보다 작은 입자들이 많이 증착되었다. 시편 뒷면에 냉각봉이 없을 때가 시편 뒷면에 냉각봉이 장착된 경우에 비하여 증착 속도가 빨랐다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1987년도 전기.전자공학 학술대회 논문집(I)
• /
• pp.461-464
• /
• 1987

With the fabrication of Al-$Al_2O_3$-n(p) type Si devices, the analysis and measurement of various characteristics, this study presented the electric physical property theory for the charge distribution of MAS device $Al_2O_3$ films, and inquired out the devices available. In order to study them, Al-(450A)$Al_2O_3$-n(p) type Si was the main objects in the study. They were examined through carrier injection, C-V curves of devices on time, ${\Delta}V_{FB}$-t curves, I-V curves and $Al_2O_3$ film's breakdown characteristics.

• 한국분말재료학회지
• /
• 제16권4호
• /
• pp.280-284
• /
• 2009

The pressureless sintering behavior of $Al_2O_3$/Cu powder mixtures, prepared from $Al_2O_3$/CuO and $Al_2O_3$/Cu-nitrate, has been investigated. Microstructural observation revealed that $Al_2O_3$ powders with nano-sized Cu particles could be synthesized by hydrogen reduction method. The specimens, pressureless-sintered at $1400^{\circ}C$ for 4 min using infrared heating furnace with the heating rate of $200^{\circ}C$/min, showed the relative density of above 90%. Maximum hardness of 16.1 GPa was obtained in $Al_2O_3$/MgO/Cu nanocomposites. The nanocomposites exhibited the enhanced fracture toughness of 4.3-5.7 $MPa{\cdot}m^{1/2}$, compared with monolithic $Al_2O_3$. The mechanical properties were discussed in terms of microstructural characteristics.

• 한국재료학회지
• /
• 제14권6호
• /
• pp.394-398
• /
• 2004

A Ti47Al1.7W-3.7Zr alloy was oxidized between $900^{\circ}C$ and $1050^{\circ}C$, and the oxide scales formed were studied. The oxide scales consisted primarily of an outer$TiO_2$ layer, an intermediate $Al_2$$O_3$-rich layer, and an inner mixed ($TiO _2$ + $Al_2$$O_3$) layer. Besides $TiO_2$ and $Al_2$$O_3$, oxidation led to the formation of some $Ti_2$AlN and TiN. Both W and Zr were preferentially segregated below the intermediate $Al_2$$O_3$-rich layer. Tungsten in the oxide scale was present as $WO_3$ and ${Ti}_{x}$$W_{1-x}$, whereas zirconium as monoclic-$ZrO_2$ and tetragonal-$ZrO_2$.

• Bulletin of the Korean Chemical Society
• /
• 제23권8호
• /
• pp.1149-1153
• /
• 2002

CH4/CO2 dry reforming was carried out to make syn gas on the Ni/Al2O3 catalysts calcined at different temperatures. The Ni/Al2O3 (850 $^{\circ}C)$ catalyst gave good activity and stability w hereas the Ni/Al2O3 $(450^{\circ}C)$ catalyst showed lower activity and stability. The NiO/Al2O3 catalyst calcined at $850^{\circ}C$ for 16 h (Ni/Al2O3 $(850^{\circ}C))$ formed the spinel structure of nickel aluminate, which was confirmed by TPR. The carbon formation rate on the Ni/Al2O3 $(850^{\circ}C)$ catalyst was very low till 20 h, and then steeply increased with reaction time without decreasing the activity for CH4 reforming. The Ni/Al2O3 $(450^{\circ}C)$ catalyst showed high carbon formation rate at the initial reaction time and then, the rate nearly stopped with continuous decreasing the activity for CH4 reforming. Even though the amount of carbon deposition on the Ni/Al2O3 $(850^{\circ}C)$ catalyst was higher than that on the Ni/Al2O3 $(450^{\circ}C)$ catalyst, the activity for CH4ing was also high, which could be attributed to the different type of the carbon formed on the catalyst surface.

• 대한기계학회논문집A
• /
• 제31권4호
• /
• pp.425-431
• /
• 2007

[ $Al_2O_3/SiC$ ]composite ceramics were sintered to evaluate the bending strength and elastic wave characteristics. The three-point bending test was carried out under room temperature. The elastic wave was detected by fracture wave detector. The crack healing behavior was investigated from 1373 K to 1723 K. The bending strength of $Al_2O_3/SiC$ composite by nanocomposite is higher than that of $Al_2O_3$ monolithic. Crack-healing behavior depended on an amount of additive powder $Y_2O_3$. In $Al_2O_3/SiC$ composite ceramics with 3 wt. % $Y_2O_3$ for additive powder, the bending strength at 1573 K is about 100% increase than that of the smooth specimens. From the result of wavelet analysis of elastic wave signal, the smooth specimen and heat treated specimen of $Al_2O_3$ monolithic and $Al_2O_3/SiC$ composite ceramics showed characteristics of frequency about 58 kHz. The strength of $Al_2O_3/SiC$ composite ceramics was a little higher than those of $Al_2O_3$ monolithic. The dominant frequencies were high with increasing of $Y_2O_3$ for additive powder. The dominant frequencies had direct connection with the bending strength.