• Progress in Superconductivity
• /
• 제9권1호
• /
• pp.5-10
• /
• 2007

We prepared four different $MgB_2$ films on $Al_2O_3$ by hybrid physical chemical vapor deposition method with thicknesses ranging from $0.65\;{\mu}m$ to $1.2\;{\mu}m$. X-ray diffraction patterns confirm that all the $MgB_2$ films are c-axis oriented perpendicular to $Al_2O_3$ substrates. The superconducting onset temperature of $MgB_2$ films were between 39.39K and 40.72K. The residual resistivity ratio of the $MgB_2$ films was in the range between 3.13 and 37.3. We measured the angle dependence of critical current density ($J_c$) and resistivity, and determined the upper critical field ($H_{c2}$) from the temperature dependence of the resistivity curves. The anisotropy ratios defined as the ratio of the $H_{c2}$ parallel to the ab-plane to that perpendicular to the ab-plane were in the range of 2.13 to 4.5 and were increased as the temperature was decreased. Some samples showed increase of $J_c$ and decrease of resistivity when a magnetic field in applied parallel to the c-axis. We interpret this angle dependence in terms of enhanced flux pinning due to columnar growth of $MgB_2$ along the c-axis.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2000년도 하계학술발표회
• /
• pp.172-173
• /
• 2000

TiN 박막은 부착력이 좋은 기계적 성질을 갖고 있으며 화학적 안정성이 뛰어난 장점을 갖고 있어 수명이 긴 박막으로 사용 할 수 있다. 또한 반도체 집적 회로소자에서는 Al과 Si 사이의 확산 방지막으로 널리 사용하고 있으며, 티타늄과 질소의 화학 조성비를 적절히 조절하여 노란 금빛을 띠는 TiN 박막을 시계나 장신구 등의 표면에 코팅하여 장식에도 많이 사용하고 있다$^{[1]}$ . 최근에는 얇은 전도성 TiN 박막을 사용하여 무반사 영역을 넓히고, 무정전 효과를 지니며, TiN 박막의 두께를 변화시켜 투과율을 조절하여 명도대비(contrast)를 향상시킬 수 있는 2층 무반사 무정전 박막을 연구하고 있다.$^{[2]}$ 여기서는 티타늄과 질소의 원소조성비에 따른 TiN 박막의 복소수 굴절률의 분산이 단 2층으로 넓은 가시광선 영역에서 무반사 효과를 가질 수 있도록 TiN 박막을 증착해야 한다. (중략)

• 한국태양에너지학회 논문집
• /
• 제39권1호
• /
• pp.33-40
• /
• 2019

Al-doped ZnO (AZO) thin films were synthesized on Si(100) wafers via plasma enhanced metal organic chemical vapor deposition (PE-MOCVD) method using diethyl zinc (DEZ) and N-methylpyrrolidine alane (MPA) as precursors. Effects of Al/Zn mixing ratio, plasma power on the surface morphology, crystal structure, and electrical property were investigated with SEM, XRD and 4-point probe measurement respectively. Growth rate of the film decreased slightly with increasing the Al/Zn mixing ratio, however electrical property was enhanced and resistivity of the film decreased greatly about 2 orders from $9.5{\times}10^{-1}$ to $8.0{\times}10^{-3}{\Omega}cm$ when the Al/Zn mixing ratio varied from 0 to 9 mol%. XRD analysis showed that the grain size increased with increasing the Al/Zn mixing ratio. Growth rate and electrical property were enhanced in a mild plasma condition. Resistivity of AZO film decreased down to $7.0{\times}10^{-4}{\Omega}cm$ at an indirect plasma of 100 W condition which was enough value to use for the transparent conducting oxide (TCO) material.

• 한국표면공학회지
• /
• 제42권6호
• /
• pp.287-293
• /
• 2009

The passivation films with epoxy layer on LiF, $SiN_x$ and LiF/$SiN_x$ inorganic layer were fabricated on OLED to protect device from the direct damage of $O_2$ and $H_2O$ and to apply for a buffer layer between OLED device and passivation multi-layer with organic/inorganic hybrid structure as to diminish the thermal stress and expansion. Red OLED doped with 1 vol.% Rubrene in $Alq_3$ was used as a basic device. The device structure was multi-layer of ITO(150 nm) / ELM200_HIL(50 nm) / ELM002_HTL(30 nm) / $Alq_3$: 1 vol.% Rubrene(30 nm) / $Alq_3$(30 nm) / LiF(0.7 nm) / Al(100 nm). LiF/epoxy applied as a protective layer didn't contribute to the improvement of life time. While in case of $SiN_x$/epoxy, damage was done in the passivation process because of difference in heat expansion between films which could occur during the formation of epoxy film. Using LiF/$SiN_x$/epoxy improved lifetime significantly without suffering damage in the process of forming films, therefore, the best structure of passivation film with inorganic/epoxy layers was LiF/$SiN_x$/E1.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2003년도 International Meeting on Information Display
• /
• pp.893-896
• /
• 2003

Plasma polymerized para-xylene (PPpX) thin films deposited by plasma enhanced chemical vapor deposition (PECVD) were used to passivate the organic light emitting diodes (OLEDs). For OLEDs, indium tin oxide (ITO), N,N'-diphenyl-N,N'-bis(3-methylphenyl)-1,1'-diphenyl-4,4'-diamine (TPD), tris(8-hydroxyquinoline) aluminum $(Alq_{3})$ and aluminum (Al) were used as the anode, the hole transport layer (HTL), the emitting layer (EML) and the cathode, respectively. The OLED device with the PPpX passivation film (passivated device) showed similar electrical and optical characteristics to those of the OLED device without the PPpX passivation film (control device), indicating that the PECVD process did not degrade the performance of the OLEDs notably. The lifetime of the passivated device was two times longer than that of the control device. Passivation of OLEDs with PPpX films also suppressed the growth of dark spots. The density and size of dark spots of the passivated device were much smaller than those of the control device.

• Progress in Superconductivity
• /
• 제13권2호
• /
• pp.117-121
• /
• 2011

We have fabricated $FeSe_x$ superconducting thin films at much different substrate temperatures of 430 and $610^{\circ}C$ on $Al_2O_3$(0001) substrates by using a pulsed laser deposition (PLD) technique. Superconducting transitions for both films were shown around 10 K, but their transition width and growth directions of grains were different. We found that superconducting tetragonal FeSe phases and non-superconducting hexagonal FeSe phases were coexisted in the sample grown at the low temperature of $430^{\circ}C$, whereas the hexagonal FeSe phase was decreased with increasing fabrication temperatures.

• 한국자기학회지
• /
• 제15권3호
• /
• pp.181-185
• /
• 2005

반응성 스퍼터링 방법으로 성장시킨 $Zn_{0.09}Cr_{0.01}O$ 묽은 자성반도체 박막의 구조와 전기 수송과 자기 특성에 미치는 Al 첨가 효과를 탐구하였다. Al이 첨가되지 않은 $Zn_{0.09}Cr_{0.01}O$ 박막은 반도체적인 수송 특성과 함께 미약한 강자성 특성을 보였다. Al을 첨가함으로써 n-형 나르개인 전자의 농도 증가와 더불어 금속성 수송 특성을 나타냈으며 포화자기화가 현저하게 증가하고 이력곡선이 뚜렷하게 나타나는 등 자기 특성의 격렬한 변화가 관찰되었다. 이 결과들은 Cr이 첨가된 ZnO에서 나르개에 의한 강자성 질서의 향상을 보여준다.

• 한국세라믹학회지
• /
• 제49권6호
• /
• pp.631-636
• /
• 2012

Conventional SONOS (poly-silicon/oxide/nitride/oxide/silicon) type memory is associated with a retention issue due to the continuous demand for scaled-down devices. In this study, $Al_2O_3/Y_2O_3/SiO_2$ (AYO) multilayer structures using a high-k $Y_2O_3$ film as a charge-trapping layer were fabricated for nonvolatile memory applications. This work focused on improving the retention properties using a $Y_2O_3$ layer with different tunnel oxide thickness ranging from 3 nm to 5 nm created by metal organic chemical vapor deposition (MOCVD). The electrical properties and reliabilities of each specimen were evaluated. The results showed that the $Y_2O_3$ with 4 nm $SiO_2$ tunnel oxide layer had the largest memory window of 1.29 V. In addition, all specimens exhibited stable endurance characteristics (program/erasecycles up to $10^4$) due to the superior charge-trapping characteristics of $Y_2O_3$. We expect that these high-k $Y_2O_3$ films can be candidates to replace $Si_3N_4$ films as the charge-trapping layer in SONOS-type flash memory devices.

• 한국정보통신학회논문지
• /
• 제7권4호
• /
• pp.712-718
• /
• 2003

진공 증착한 CdS 박막의 질소 이온 주입 효과를 X-선 회절 검사, 광 투과율, 라만 산란 특성을 통하여 조사하였다. 질소 이온 주입하지 않은 CdS 박막은 (0 0 2)면으로의 우선 방위를 가지고 성장하였다. 질소 이온 주입한 시편의 경우 metallic Cd가 형성됨을 XRD 분석 결과 알 수 있었다. 가시광 영역에서의 광투과율은 질소 이온 주입 양이 많아짐에 따라 크게 감소하였다. 또한 질소 이온 주입 양에 따라 CdS 박막의 흡수 계수는 지수 함수적으로 증가하였고, 밴드 갭은 감소하였다 CdS 박막의 라만 peak 위치는 질소 이온 주입 양에 관계없이 299 cm-1로 거의 일정하지만, peak의 FWHM은 이온 주입 양이 증가함에 따라 커졌고, peak 면적은 감소하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 추계학술대회 논문집
• /
• pp.125-128
• /
• 1998

Electroluminescent(EL) devices based on organic thin films have attracted lots of interests in large-area light-emitting display. One of the problems of such device is a lifetime, where a degradation of the cell is possibly due to an organic layer's thickness, morphology and interface with electrode. In this study, light-emitting organic electroluminescent devices were fabricated using Alq$_3$(8-hydroxyquinolinate aluminum) and TPD(N,N'-diphenyl-N,N'-bis(3-methylphenyl)-[1-1'-biphenyl]-4,4'-diamine).Where Alq$_3$ is an electron-transport and emissive layer, TPD is a hole-transport layer. The cell structure is ITO/TPD/Alq$_3$/Al and the cell is fabricated by vacuum evaporation method. In a measurement of current-voltage characteristics, we obtained a turn-on voltage at about 9 V. And we used other buffer layer of PPy(Polypyrrole) with ITO/PPy/TPD/Alq$_3$/Al structure. We observed a surface morphology by AFM(Atomic Force Microscopy), UV/visible absorption spectrum, and PL(Photoluminescence) spectrum. We obtained the UV/visible absorption peak at 358nm in TPD and at 359nm in Alq$_3$, and at 225nm and the PL peaks at 410nm in TPD and at 510nm in Alq$_3$ and at 350nm. We also studied EL spectrum in the cell structure of ITO/TPD/Alq$_3$/Al and ITO/PPy/TPD/Alq$_3$/Al and we observed the EL spectrum peak at 510nm from our cell