• 소성∙가공
• /
• 제21권1호
• /
• pp.49-57
• /
• 2012

It is difficult to estimate the properties of multilayered sheet because they are composed of one or more different materials. Plastic deformation behavior of the multilayered sheet is quite different as compared to each material individually. The deformation behavior of multilayered sheet should be investigated in order to prevent forming defects and to predict the properties of the formed part. In this study, the mechanical properties and formability of stainless steel-aluminum-magnesium multilayered sheet were investigated. The multilayered sheet needs to be deformed at an elevated temperature because of its poor formability at room temperature. Uniaxial tensile tests were performed at various temperatures and strain rates. Fracture patterns changed mainly at a temperature of $200^{\circ}C$. Uniform and total elongation of multilayered sheet increased to values greater than those of each material when deformed at $250^{\circ}C$. The limiting drawing ratio (LDR) was obtained using a circular cup deep drawing test to measure the formability of the multilayered sheet. A maximum value for the LDR of about 2 was achieved at $250^{\circ}C$, which is the appropriate forming temperature for the Mg alloy. Fracture patterns on a circular cup and thickness of formed part were predicted by a rigid-viscoplastic FEM analysis. Two kinds of modeling techniques were used to simulate deep drawing process of multilayered sheet. A single-layer FE-model, which combines the three different layers into a macroscopic single layer, predicted well the thickness distribution of the drawn cup. In contrast, the location and the time of fracture were estimated better with a multi-layer FE model, which used different material properties for each of the three layers.

• 한국재료학회지
• /
• 제17권5호
• /
• pp.256-262
• /
• 2007

Effects of interlayer and the combination of different coating methods on the mechanical and corrosion behaviors of TiN and CrN coated on 420 stainless steel have been studied. STS 420 specimen were tempered at $300^{\circ}C$ for 1 hr in vacuum furnace. The TiN and CrN thin film with 2 ${\mu}m$ thickness were coated by arc ion plating and DC magnetron sputtering following the formation of interlayer for pure titanium and chromium with 0.2 ${\mu}m$ thickness. The microstructure and surface analysis of the specimen were conducted by using SEM, XRD and roughness tester. Mechanical properties such as hardness and adhesion also were examined. XRD patterns of TiN thin films showed that preferred TiN (111) orientation was observed. The peaks of CrN (111) and $Cr_2N$ (300) were only observed in CrN thin films deposited by arc ion plating. Both TiN and CrN deposited by arc ion plating had the higher adhesion and hardness compared to those formed by magnetron sputtering. The specimen of TiN and CrN on which interlayer deposited by magnetron sputtering and thin film deposited by arc ion plating had the highest adhesion with 22.2 N and 19.2 N. respectively. TiN and CrN samples shown the most noble corrosion potentials when the interlayers were deposited by using magnetron sputtering and the metal nitrides were deposited by using arc ion plating. The most noble corrosion potentials of TiN and CrN were found to be approximately -170 and -70 mV， respectively.

• 마이크로전자및패키징학회지
• /
• 제27권4호
• /
• pp.127-133
• /
• 2020

고분자 재료인 접착제와 금속 피착재 사이의 정량적인 접착강도 측정은 중요하다. 고분자 재료인 접착제와 금속 피착재 사이의 접착강도 측정 시, 피착재의 종류와 두께 변화가 접착강도에 미치는 영향에 대해 연구하였다. 금속 피착재의 종류로는 알루미늄과 스텐리스강 2종류가 선택되었으며, 접착강도의 측정에는 돌리테스트와 전단시험이 사용되었다. 인장응력 방식의 돌리테스트로 고분자 접착제와 금속 피착재 사이의 접착강도 측정 시, 금속 피착재의 두께 변화는 접착강도의 크기에 거의 영향을 미치지 않았으나, 피착재의 종류에 따라 접착강도는 다르게 나타났다. 반면, 전단시험으로 고분자 접착제와 금속 피착재 사이의 접착강도 측정 시, 금속 피착재의 상대적 두께 변화는 접착강도의 크기에 영향을 주었다. 이유는 전단시험 시 접착부의 모서리 부분에서 발생하는 피착재의 휘어짐 현상은 접착부에 추가적인 인장응력을 발생시켜 접착강도를 낮추는데 기여하기 때문이다. 이 연구의 결과, 돌리테스트는 피착재의 두께가 변해도 접착강도의 변화가 거의 없기 때문에 고분자 접착제와 금속 피착재의 정량적인 접착강도 측정 시 널리 사용될 것으로 예상된다.