• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.187.1-187.1
• /
• 2014

아연 가격의 상승과 경량합금개발의 중요성이 부각됨에 따라 아연을 대체할 새로운 강판용 내식소재의 개발이 중요하다. Al-Mg 합금 박막은 낮은 밀도를 가지면서 질량 대비 높은 강도, 좋은 내식성을 지녀 아연도금강판을 대체할 코팅소재로 그 가능성이 연구되고 있다. 이러한 Al-Mg 합금 박막의 실용화를 위해 국내외의 관련 연구그룹에서 연구를 진행하고 있으며, 그 결과 Al-Mg 합금 박막의 내식성 및 기계적 특성은 박막의 조성 및 미세구조와 상당한 관련성이 있음이 알려지고 있다. 본 연구에서는 sputtering법으로 냉연 강판에 Al-Mg 합금을 조성 및 열처리 여부 등을 조절하여 증착시킨 후 각 조건에 따른 박막의 미세구조와 기계적 특징을 조사하였다. 각 조건별 내마모도와 경도, 마찰계수, 밀착력을 분석하여 기계적 특성과 미세구조와의 상관관계를 도출하고자 하였다.

• Journal of Korea Foundry Society
• /
• v.36 no.6
• /
• pp.181-186
• /
• 2016

The typical microstructure of Al-5%Mg-2%Zn cast alloy mainly consists of an aluminum matrix with a small amount of AlMgZn 2nd phase. The secondary dendrite arm spacing and the grain size of the cast alloy tend to be inversely proportional to the section thickness of casting; however, the tensile properties cannot be said to be clearly related to the cast microstructure. After T6 heat treatment, the tensile strength of the alloy was enhanced significantly. TEM analysis results show that very fine AlMgZn precipitates were formed after the heat treatment. The corrosion resistance, measured according to the corrosion potential, was found to increase slightly after the conducting of heat treatment.

• Journal of the Korean Society for Heat Treatment
• /
• v.11 no.1
• /
• pp.10-16
• /
• 1998

The softening behavior of squeeze cast Mg-Li-Al and Mg-Li-Al-Zr alloys have been investigated. The highest hardness values of Mg-Li-Al and Mg-Li-Al-Zr alloys were obtained after solution treatment at $400^{\circ}C$ for 1 hour. The hardness value, however, decreased as the aging temperature and time increased. Microstructural and calorometric analyses showed that quenched-microstructure changed from primary (${\alpha}$ and ${\beta}$)+secondary ${\alpha}$ to primary(${\alpha}$ and ${\beta}$)+secondary ${\alpha}+{\theta}$ after aging. The softening during aging was due to the coarsening of ${\theta}$ precipitates.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2013.05a
• /
• pp.150-150
• /
• 2013

Al-Mg films were prepared onto steel sheet according to deposition condition by eco-friendly electron beam vacuum evaporation method. The influence of Al-Mg films on corrosion resistance was evaluated by salt spray test and electrochemical method etc.. From the experimented results, it was found that the Al-Mg films which showed good corrosion resistance tend to have fine structure with homogenious composition distribution. In addition, it was shown that the property of coating films can be improve by controlling thickness ratio and uniform distribution of intermetallic compounds in Al-Mg films.

• Applied Microscopy
• /
• v.29 no.3
• /
• pp.281-289
• /
• 1999

The stirred and thixoformed $SiC_p/AZ91HP$ Mg composites are studied on the basis of microstructural analysis using transmission electron microscopy (TEM). The products of interfacial reaction are identified as $Mg_2Si$, MgO and $Mg_{17}Al_{12}$ phases and the crystallized phases are found to be orthorhmbic $Al_6Mn$ and decagonal T phases. It is shown that $Mg_2Si$ and $Mg_{17}Al_{12}$ phases are found at the surface of $SiC_p$ and $Al_6Mn$ is found near interface and crystallized on the matrix. Phase identification is carried out by crystallographic work based on primitive cell volume, zero order Laue zone (ZOLZ) patterns and single convergent beam electron diffraction (CBED) patterns containing higher order Laue zone ring from a nanosized region.

• Journal of the Korean Ceramic Society
• /
• v.20 no.1
• /
• pp.37-42
• /
• 1983

An attempt was made to derive a possible synthetic mechanism of Fluoro-phlogopite (Mica, 4Mg.$Al_2O_3$.$6SiO_2$.$K_2O$.$2MgF_2$) The pevention of fluorine vaporization turned out to be the key in the synthesis of Mica in question.l Consequently the quinary system of Mica was seperately synthesized ; frist 4MgO.$Al_2O_3-6SiO_2$(ternary system) was sintered at 135$0^{\circ}C$ and $K_2O$ and $MgF_2$ were added and second 4MgO.$Al_2O_3-6SiO_2$.$K_2O$ (quarternary system) was heat-treated at 135$0^{\circ}C$ and $MgF_2$ was added. The ternary system resulted in Proto-enstatite Cordierite and Spinel phases while Forsterite and Leucite were shown in the quarternay system . In both methods Fluoro-phlogopite was systhesized but the solid state reactions to form Mica from the ternary system and the quarternary system were different. High temperature reactions in the formation of Mica were investigated employing XRD, DTA and SEM The study of the synthesis of Mica indirectly suggested a method of phase analysis of quinary system(MgO-$Al_2O_3-SiO_2-K_2O-MgF_2$) and quarternary system(MgO-$Al_2O_3-SiO_2-K_2O-MgF_2$) at various temperatures.

• Proceedings of the KWS Conference
• /
• 2000.04a
• /
• pp.71-74
• /
• 2000

자기 구속 균열 시험법인 Tapered 시편 균열 시험법을 이용하여 Al-Mg 합금의 CW $CO_2$ 레이저 용접시 Mg 함량 변화에 따른 고온균열감수성 변화를 조사하였다. Mg 함량 1.9wt.%에서 최대균열감수성을 나타내고 있으며 이보다 Mg 함량이 증가하거나 감소하면 고온균열 감수성이 감소한다. 용접금속 결정립 크기 또한 고온균열감수성과 관련이 있으며 Mg 함량이 증가할수록 결정립이 미세화되며, 1.9wt.%Mg 이상에서 결정립이 미세화될수륵 고온균열 감수성 이 감소한다.

• Journal of Korea Foundry Society
• /
• v.32 no.6
• /
• pp.289-295
• /
• 2012

Mg-Al-Sn-Si system alloy, as a promising cheap heat-resistant Mg alloy for automobile engine part, has been investigated. Refinement of microstructure and precipitation of thermally stable secondary phases are important goal for the design of heat-resistant Mg alloy. In this study, the effect of Ce on the microstructure and room temperature mechanical properties of Mg-Al-Sn-Si alloy was investigated. High thermally stable $Mg_2Si$ phases in Mg-Al-Sn-Si alloy is very useful intermetallic compound. However, the $Mg_2Si$ phases often result in poor mechanical properties due to the coarse chinese type $Mg_2Si$ phases. The experimental specimens were fabricated by fluxless melting under $CO_2+SF_6$ atmosphere and poured into the permanent pre-heated at $200^{\circ}C$. It was told that Ce addition can modify $Mg_2Si$ phases and refine microstructure and improve the tensile strength, yield strength and elongation.

• Journal of Powder Materials
• /
• v.7 no.1
• /
• pp.12-18
• /
• 2000

Effects of the microstrucrure of rapidy solidified Al-Pb-Cu-Mg alloys on the wear investigated. In order to overcome the miscility gap between Al and pb under equilibrium conditions, both in the solid and the liquid states, the alloy were rapidy solidifies to produce them in a segregation-free condition. Although the Pb particles showed relatively fine dispersion in the Al matrix in all the alloys by this process. the Al-16Pb alloy was found to have the most favorable microstructure with discretre with discrete Pb particles of abount 0.5 ${\mu}$m in size. With the addition of Cu and Cu-Mg to Al-16Pb, cellular structures were newly formed; not seen in the binary Al-Pb alloy. Wear properties of the Al-Pb binary alloys measured as a function of the sliding speen, sliding distance, and applied load showed that the Al-16Pb alloy has the best wear resistance, as expected from the fine microstructural features in this alloy. The were resistance of the alloy containing Cu-and Cu-Mg was higher than that of the Al-16Pvb alloy, due to matrix strengthening by precipitation hardeing. The wear mechanism was identified by examining the traces and wear debris.

• Journal of the Korean Society for Heat Treatment
• /
• v.20 no.6
• /
• pp.293-298
• /
• 2007

Influences of aluminum carbide ($Al_4C_3$) addition on microstructure and damping capacity of Mg-3%Al casting alloy have been investigated based on experimental results of optical micrography, scanning electron microscopy with energy-dispersive spectrometry analysis and damping capacity measurement at RT. The addition of $Al_4C_3$ particles results in an efficient grain refinement. The damping capacity shows an increasing tendency with an increase in $Al_4C_3$ content. The damping value associated with $Al_4C_3$ particles is linearly dependent on the volume fraction of $Al_4C_3$ particles to the 2/3 power, $f_{2/3}$, which corresponds to the total surface area of the particles.