• Korean Journal of Materials Research
• /
• v.7 no.7
• /
• pp.564-570
• /
• 1997

용융산화에 의한 AI$_{2}$O$_{3}$복합재료의 형성에 미치는 합금원소의 영향을 연구하였다. AI-Mg-3Si 합금이 가장 우수한 산화거동을 보였다. 우수한 3원계로 선정된 AI-1Mg-3Si합금에 제 4원소 Sn, Cu, Ni, Zn을 양을 달리하여 각각 첨가하여 산화거동을 살펴보았다. 1273K, 1373K, 1473K, 에서 20시간 각각 산화실험을 한 결과, 1473K에서는 모든 합금계가 우수했으나 1373K, 1273K에서는 산화가 거의 일어나지 않았다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.05a
• /
• pp.155-156
• /
• 2015

최근 자동차 및 항공기의 경량화 관련하여 알루미늄 합금의 필요성이 높아지고 있으나, 자동차재료에 쓰이는 알리미늄 합금의 경우 높은 이온화 경향 때문에 Fe, Cu, Pb 등과 접촉하면 쉽게 부식되는 단점이 있다. 본 연구에서는 기존의 Magsimal-59 샘플과 본 연구에서 개발한 고용질, 저용질 Duplex 알루미늄 합금과의 내식성을 분극 및 갈바닉을 통해 확인하고, 균질화처리를 통해 내식성을 개선한다.

• Journal of Korea Foundry Society
• /
• v.30 no.1
• /
• pp.29-33
• /
• 2010

The microstructure of Al-5%Mg based alloy mainly consists of aluminum matrix with a small amount of AlMn phase. The addition of Sc or Zn to the base alloy significantly improved the as-cast tensile strength, while the addition of Fe deteriorated both strength and ductility. Although the Al-5%Mg based alloy was not heat-treatable, aging hardening could be observed in the case that Sc or Zn was added to the base alloy. TEM analysis showed that very fine AlSc or AlMgZn precipitates were formed after T6 heat treatment, resulting in enhanced strength. The corrosion resistance measured as corrosion potential was found to decrease a little by adding Zn, whereas other alloying elements were not clearly influential.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.172-175
• /
• 2003

Thermomechanical behavior of Al-Mg-Si alloys have been studied to investigate the effect of microstructural features such as pre-existing substructure and distribution of particles on the deformation characteristics. The controlled compression tests have been carried out to get the basic information on how the alloy responds to temperature, strain amount and strain rate. Then hot forging of Al-Mg-Si alloys has been carried out and analyzed by the comparison with the compression tests. Microstructural features after forging have been discussed in terms of the thermomechanical response of Al-Mg-Si alloys. As already well mentioned, we have found that the deformation of Al-Mg-Si at the elevated temperature brought the recovered structure on most conditions. In a certain time, however, abnormally large grains have been found as a result of deformation assisted grain growth, which means that hot forging of Al-Mg-Si alloys could lead to a undesirable microstructural variation and the consequent mechanical properties such as fatigue strength.

• Transactions of Materials Processing
• /
• v.13 no.1
• /
• pp.27-32
• /
• 2004

Thermomechanical behavior of Al-Mg-Si alloys was studied to investigate the effect of microstructural features such as pre-existing substructure and distribution of particles on the deformation characteristics. The controlled compression tests were carried out to get the information on how the alloy responds to temperature, strain amount and strain rate. Then hot forging of Al-Mg-Si alloys carried out and analyzed by the comparison with the compression tests. Microstructural features after forging were discussed in terms of the thermomechanical response of Al-Mg-Si alloys. As already well mentioned, we found that the deformation of Al-Mg-Si at the elevated temperature brought the recovered structure on most conditions. In a certain time, however, abnormally large grains were found as a result of deformation assisted grain growth, which means that hot forging of Al-Mg-Si alloys could lead to a undesirable microstructural variation and the consequent mechanical properties such as fatigue strength.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.146-146
• /
• 2016

최근 국민 소득향상과 더불어, 여가시간 증가에 따라 해양레저에 대한 관심이 크게 높아지고 있으며, 그에 따라 레저용 선박 수요도 증가하고 있다. 기존 국내 소형 선박의 경우 FRP(fiber-reinforced plastic)재료로 선박을 건조해 왔다. 그러나 해양환경 규제 강화로 FRP 선박의 건조가 감소하고 있으며, 친환경 선박에 대한 필요성이 대두되고 있다. 따라서 FRP재료를 대체하는 선박용 재료로 친환경적이고 가벼운 소재인 알루미늄 합금 재료가 선박건조 분야에서 각광을 받고 있다. 특히 5000계열 Al-Mg 합금은 가공성과 용접성이 우수하여 주로 구조용으로 많이 사용되고 있으나 경량화에 따른 빠른 선속이 유체충격을 증가시켜 선체에 캐비테이션 손상을 일으킬 수 있다. Al-Mg 합금의 경우에 부식성이 대단히 큰 해양환경에서 부식과 캐비테이션 침식이 복합적으로 일어나면 손상이 빠르게 증가되는 경향을 나타내어 선박의 수명을 현저히 단축시켜 경제적인 손실을 초래한다. 따라서 본 연구에서는 해수 내에서 Al-Mg 합금의 캐비테이션 저항성을 향상시키기 위해 알루미늄 합금 표면에 내식성 뿐만 아니라 경도 및 내마모성 등의 기계적 특성이 우수한 산화피막을 형성시키는 양극산화 기술을 적용하고, 다양한 봉공처리(sealing)방법에 따른 캐비테이션 특성을 평가하였다. 캐비테이션 실험은 압전(piezoelectric) 효과를 이용한 진동발생 장치를 사용하여 $30{\mu}m$ 진폭으로 일정하게 유지하였으며, 시편과 혼 팁 사이의 간격은 1mm로 하였다. 캐비테이션 실험 후에는 시편을 초음파 세척하여 진공 건조기에서 24시간 이상 건조한 후 정밀저울로 무게를 측정하였으며, 표면 손상 형상을 분석하기 위해 주사전자현미경(SEM)과 3D현미경을 이용하여 관찰하였다.

• Journal of the Korean Ceramic Society
• /
• v.33 no.9
• /
• pp.985-994
• /
• 1996

The initiation and growth of $\alpha$-Al2O3/metal composites by the directed oxidation of molten commercial AlZnMg-alloy at 1223-1423K were investigated. Spontaneous bulk growth did not occur on the alloy alone. but the uniform initiation and growth of the composite were obtained by putting a thin layer of SiO2 particles on the surface of the alloy. Without SiO2 the external surface of the oxide layer was convered by MgO and MgAl2O4. But with the SiO2 reaction initiate the porous ZnO layers were found on the growth surface. The higher process temperature yielded a lower metal content. The oxidation product of $\alpha$-Al2O3 was found to be oriented with c-axis parallel to th growth direction. The growth rates increased with temperature and the apparent activation energy was 111.8 kJ/mol.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.12
• /
• pp.1675-1682
• /
• 2012

Weight reduction is increasingly being considered very important in light of air pollution and the exhaustion of resources. As a result, many automotive components are being replaced by Al and Mg alloys, and studies are increasingly focusing on the same. However, the use of Mg alloys is limited because they have higher material cost and lower productivity owing to the difficult forming conditions compared with Al alloys. In this study, the tube extrusion process conditions of an automotive bumper back beam were analyzed using FEA. Material tests were performed to determine the properties, and experiments and analyses for a simple shape were performed to define the data for heat generation during plastic deformation. Then, the analyses of the product were carried out by considering various temperatures and ram speeds. The conditions were then established, and a product without surface defects was extruded successfully.

• Journal of Korea Foundry Society
• /
• v.23 no.3
• /
• pp.153-157
• /
• 2003

본 논문은 레오캐스팅용 AZ91 합금 슬러리를 제조하는 새로운 방법에 관한 것이다. 그 원리는 AZ91 합금 액상에서 Mn의 용해도차에 의해 생성되는 $Al_8(Mn,Fe)_5$ 정출물을 ${\alpha}-Mg$ 초정 생성을 위한 불균일 핵생성 자리로 사용하고자 하는 것이다. 제조된 슬러리의 미세조직 분석결과 $Al_8(Mn,Fe)_5$ 정출물이 ${\alpha}-Mg$ 내에 위치하고 있어, 이로부터 정출물이 효과적으로 불균일 핵생성 자리로 작용하고 있음을 알 수 있었다. 또한 Mn 함량의 증가는 $Al_8(Mn,Fe)_5$ 정출물 수를 증가시켜 고상분율이 일정할 때 슬러리 내 ${\alpha}-Mg$ 고상의 크기를 감소시키고 구형도를 향상시킨다. 이외에도 냉각속도 및 유지시간이 슬러리 미세조직에 미치는 영향에 대해서도 보고하였다.

• Journal of Korea Foundry Society
• /
• v.30 no.4
• /
• pp.137-141
• /
• 2010

The effects of Zn amounts on the castability and tensile properties of Al-Zn-Mg-Cu alloys were investigated for development of high strength die casting aluminium alloys. Al-Zn-Mg-Cu alloys with 3.5% Zn showed high cast cracking tendency and poor mold filling behaviour. Al-Zn-Mg-Cu alloys with 5wt% Zn and 7wt% Zn had the tensile strengths of 300~400MPa and the elongations of 2~18%. The effect of Zn on the tensile strength of Al-Zn-Mg-Cu alloys was insignificant, but Al-Zn-Mg-Cu alloy with high Zn amount had lower elongation.