• Journal of Korea Foundry Society
• /
• 제25권3호
• /
• pp.134-141
• /
• 2005

To overcome the undesirable deformation, peeling off and geometrical restrictions which were mainly caused by differences in thermal expansion coefficients during the cladding of aluminum strip and stainless strip, new processing method based on vacuum die casting is designed and implemented in fabricating Al/Fe-17wt%Cr steel(stainless steel). To increase cast-bonding ability, the surface of Fe-17wt%Cr steel is electrochemically etched to have optimum pit size and density. The optimum conditions to generate best pit are as follows: Solution: 1 M $Fecl_{3}$+1 M Nacl, Addition: $CuCl_{2}+HCl$, Current density: 80 $mA/cm^{2}$, Total current: 400 $coulomb/cm^{2}$, AC frequency :60 Hz.

• Korean Journal of Materials Research
• /
• 제11권11호
• /
• pp.986-990
• /
• 2001

An optimum route to fabricate the $A1_2O_3/Fe-Ni$ alloy nanocomposites with sound microstructure and enhanced mechanical properties as well as magnetism was investigated. To prepare homogeneous nanocomposite powders of Fe-Ni alloy and $Al_2O_3$, the solution-chemistry routes using $Al_2O_3 \; Ni(NO_3)_2{\cdot}6H_2O$ and $Fe(NO_3)_3{\cdot}9H_2O$ powders were applied. Microstructural observation of the powder mixture revealed that the Fe-Ni alloy particles of about 20 nm in size were homogeneously surrounded $A1_2O_3$, forming nanocomposite powder. The hot-pressed composite showed improved fracture toughness and magnetic response. These results suggest that the synergy materials with an improved mechanical properties and excellent functionality can be fabricated by controlled powder preparation and consolidation processing.

• Korean Journal of Materials Research
• /
• 제2권2호
• /
• pp.143-150
• /
• 1992

Crystal structures and magnetic properties of annealed Co-(Al-Fe) alloys have been investigated. Annealed specimens showed superparamagnetism when x=0.05 and ferromagnetism when $x{\geq}0.10$. Magnetization increased as x increased. X-ray diffraction data revealed that specimens were single-phase in B2(CsCl) structure with constant lattice parameter $2.87{\AA}$. The experimental results were analized on the point of view of the local environmental effect of magnetic atoms.

• Journal of Magnetics
• /
• 제10권4호
• /
• pp.137-141
• /
• 2005

We confirmed that the improvement in properties of magnetic tunnel junctions prepared by radical oxidation after thermal treatment was mostly resulted from the redistribution of oxygen at the $AIOx/Co_{90}Fe_{10}$ interface. The as-deposited Al oxide barrier was oxygen-deficient but most of it re-oxidized into $Al_2O_3$, the thermodynamically stable stoichiometric phase, through thermal treatment. As a result, the effective barrier height was increased from 1.52 eV to 2.27 eV. On the other hand, the effective barrier width was decreased from 8.2 ${\AA}$ to 7.5 ${\AA}$. X-ray absorption spectra of Fe and Co clearly showed that the oxygen in the CoFe layer diffused back into the Al barrier and thereby enriched the barrier to close to a stoichiometirc $Al_2O_3$ phase. The oxygen bonded with Co and Fe diffused back by 6.8 ${\AA}$ and 4.5 ${\AA}$ after thermal treatment, respectively. Our results confirm that controlling the chemical structures of the interface is important to improve the properties of magnetic tunnel junctions.

• Proceedings of the Mineralogical Society of Korea Conference
• /
• 한국광물학회.한국암석학회 2001년도 공동학술발표회 논문집
• /
• pp.38-39
• /
• 2001

The seasonal changes in pH, Fe, Al and SO$_4$$\^$2-/ contents of acid drainage released from coal mine dumps play a major role in precipitation of metal hydroxides in the Taebaek coal field area, southeastern Korea. Precipitates in the creeks underwent a cycle of the color change showing white, reddish brown and brownish yellow, which depends on geochemical factors of the creek waters. White precipitates consist of Al-sulfate (basaluminite and hydrobasaluminite) and reddish brown ones are composed of ferrihydrite and brownish yellow ones are of schwertmannite. Goethite coprecipitates with ferrihydrite and schwertmannite. Ferrihydrite formed at higher values than pH 5.3 and schwertmannite precipitated below pH 4.3, and goethite formed at the intermediate pH range between the two minerals. With the pH being increased from acid to intermediate regions, Fe is present both as schwertmannite and goethite. From the present observation, the most favorable pH that basauluminte can precipitate is in the range of pH 4.45-5.95. SEM examination of precipitates at stream bottom shows that they basically consist of agglomerates of spheroid and rod-shape bacteria. Bacteria species are remarkably different among bottom precipitates and, to a less extent, there are slightly different chemical compositions even within the same bacteria. The speciation and calculation of the mineral saturation index were made using MINTEQA2. In waters associated with yellowish brown precipitates mainly composed of schwertmannite, So$_4$ species is mostly free So$_4$$\^$2-/ ion with less AlSo$_4$$\^$+/, CaSo$\sub$(aq)/, and MgSo$\sub$4(aq)/. Ferrous iron is present mostly as free Fe$\^$2+/, and FeSo$\sub$4(aq)/ and ferric iron exists predominantly as Fe(OH)$_2$$\^$+/, with less FeSo$\sub$4(aq)/, Fe(OH)$_2$$\^$-/, FeSo$_4$$\^$-/ and Fe$\^$3+/, respectively Al exists as free Al$\^$3+/, AlOH$_2$$\^$-/, (AlSo$_4$)$\^$+/, and Al(So$_4$)$\^$2-/. Fe is generally saturated with respect to hematite, magnetite, and goethite, with nearly saturation with lepidocrocite. Aluminum and sulfate are supersaturated with respect to predominant alunite and less jubanite, and they approach a saturation state with respect to diaspore, gibbsite, boehmite and gypsum. In the case of waters associated with whitish precipitates mainly composed of basaluminite, Al is present as predominant Al$\^$3+/ and Al(SO$_4$)$\^$+/, with less Al(OH)$\^$2+/, Al(OH)$_2$$\^$+/ and Al(SO$_4$)$\^$2-/. According to calculation for the mineral saturation, aluminum and sulfate are greatly supersaturated with respect to basaluminite and alunite. Diaspore is flirty well supersaturated while jubanite, gibbsite, and boehmite are already supersaturated, and gypsum approaches its saturation state. The observation that the only mineral phase we can easily detect in the whitish precipitate is basaluminite suggests that growth rate of alunite is much slower than that of basaluminite. Neutralization of acid mine drainage due to the dilution caused by the dilution effect due to mixing of unpolluted waters prevails over the buffering effect by the dissolution of carbonate or aluminosilicates. The main factors to affect color change are variations in aqueous geochemistry, which are controlled by dilution effect due to rainfall, water mixng from adjacent creeks, and the extent to which water-rock interaction takes place with seasons. pH, Fe, Al and SO$_4$ contents of the creek water are the most important factors leading to color changes in the precipitates. A geochemical cycle showing color variations in the precipitates provides the potential control on acid mine drainage and can be applied as a reclamation tool in a temperate region with four seasons.

• Proceedings of the Korean Magnestics Society Conference
• /
• 한국자기학회 2002년도 동계연구발표회 논문개요집
• /
• pp.14-15
• /
• 2002

Iron nitride alloy films prepared in the form of laminated ${(Fe_{97}Al_3)}_{85}N_{15}/Al_2O_3$ multilayers (Ml's) due to excellent soft magnetic properties and high saturation magnetization [1, 2] are very promising materials for poles and shields in ultra high density thin film heads. The present work concerns the ferromagnetic (FM) coupling effect as a function of the thickness of $Al_2O_3$ spacers by analysis of the magnetic domain structure.

• Korean Journal of Metals and Materials
• /
• 제50권8호
• /
• pp.575-582
• /
• 2012

Medium carbon steel was aluminized by hot dipping into molten Al or Al-1 at% Si baths. After hot-dipping in these baths, a thin Al-rich topcoat and a thick alloy layer rich in $Al_5Fe_2$ formed on the surface. A small amount of FeAl and $Al_3Fe$ was incorporated in the alloy layer. Silicon from the Al-1 at% Si bath was uniformly distributed throughout the entire coating. The hot dipping increased the microhardness of the steel by about 8 times. Heating at $700-1000^{\circ}C$, however, decreased the microhardness through interdiffusion between the coating and the substrate. The oxidation at $700-1000^{\circ}C$ in air formed a thin protective ${\alpha}-Al_2O_3$ layer, which provided good oxidation resistance. Silicon was oxidized to amorphous silica, exhibiting a glassy oxide surface.

• Journal of Welding and Joining
• /
• 제34권3호
• /
• pp.6-11
• /
• 2016

Joining Al/Fe dissimilar metals is becoming a subject of special interest in the assembly of automotive parts as a trade-off between the weight lightening and the cost reduction. Although various studies have been introduced to join Al alloy with the steel sheet by fusion welding, weak joint strength and galvanic corrosion still remained as problems to be solved. As a solid state welding, friction stir welding has been preferred to fusion welding processes in the dissimilar metal joints. This study investigated friction stir spot welding (FSSW) of Al alloy to the thin steel sheet with a thickness of 0.65 mm. The conventional FSSW is a stationary spot welding process but new approach adopted an additional circumferential movement in company with high speed tool rotation. A full factorial experimental design was implemented, and the main and interaction effects of parameters were analysed on the failure load in the tensile shear test. The direction and radius of rotation were statistically significant parameters and these two parameters affected the joint width and the shape of the hook.

• Journal of Magnetics
• /
• 제19권1호
• /
• pp.55-58
• /
• 2014

We have synthesized ferromagnetic ${\tau}$-phase $Mn_{54}Al_{46}/{\alpha}$-phase $Fe_{65}Co_{35}$ composite by annealing a mixture of paramagnetic ${\varepsilon}$-phase $Mn_{54}Al_{46}$ and ferromagnetic ${\alpha}$-phase $Fe_{65}Co_{35}$ particles at $650^{\circ}C$. The volume fraction ($f_h$) of hard ${\tau}$-phase $Mn_{54}Al_{46}$ of the composite was varied from 0 to 1. During the annealing, magnetic phase transformation occurred from paramagnetic ${\varepsilon}$-phase to ferromagnetic ${\tau}$-phase $Mn_{54}Al_{46}$. The magnetization and coercivity of the composite monotonically decreased and increased, respectively, as the $f_h$ increased. These results are in good agreement with our proposed composition dependent coercivity and modified magnetization equations.

• Advances in materials Research
• /
• 제2권4호
• /
• pp.221-235
• /
• 2013

To obtain bronze with good mechanical properties and high wear resistance, a new bronze (CADZ) is proposed on the basis of various fundamental information. The CADZ consists of the elements Al10.5, Fe4.2, Sn3.7 and Ni3.1, and its design is based on Cu-Al10.5 alloy. The Cu-10.5%Al is very hard and brittle. To obtain the high material ductility of the Cu-10.5%Al alloy, an attempt was made to add a few percent of Sn. Moreover, to make high strength of the Cu alloy, microstructure with small grains was created by the proper amount of Fe and Ni (Fe/Ni = 0.89). The mechanical properties of the CADZ sample have been examined experimentally, and those were compared with commercial bronzes. The tensile strength and wear resistance of CADZ are higher than those for commercial bronzes. Although the ductility of CADZ is the lower level, the strain to failure of CADZ is about 2.0~5.0% higher than that for the Cu-Al10.5 alloy. Details of the microstructural effects on the mechanical properties in the CADZ sample were further discussed using various experimental results.