• 한국재료학회지
• /
• 제21권8호
• /
• pp.468-475
• /
• 2011

[ $LaMeO_3$ ](Me = Cr, Co) powders were prepared using the polymeric precursor method. The effects of the chelating agent and the polymeric additive on the synthesis of the $LaMeO_3$ perovskite were studied. The samples were synthesized using ethylene glycol (EG) as the solvent, acetyl acetone (AcAc) as the chelating agent, and polyvinylpyrrolidone (PVP) as the polymer additive. The thermal decomposition behavior of the precursor powder was characterized using a thermal analysis (TG-DTA). The crystallization and particle sizes of the $LaMeO_3$ powders were investigated via powder X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and particle size analyzer, respectively. The as-prepared precursor primarily has $LaMeO_3$ at the optimum condition, i.e. for a molar ratio of both metal-source (a : a) : EG (80a : 80a) : AcAc (8a) inclusive of 1 wt% PVP. When the as-prepared precursor was calcined at $700^{\circ}C$, only a single phase was observed to correspond with the orthorhombic structure of $LaCrO_3$ and the rhombohedral structure of $LaCoO_3$. A solid-electrolyte impedance-metric sensor device composed of $Li_{1.5}Al_{0.5}Ti_{1.5}(PO_4)_3$ as a transducer and $LaMeO_3$ as a receptor has been systematically investigated for the detection of NOx in the range of 20 to 250 ppm at $400^{\circ}C$. The sensor responses were able to divide the component between resistance and capacitance. The impedance-metric sensor for the NO showed higher sensitivity compared with $NO_2$. The responses of the impedance-metric sensor device showed dependence on each value of the NOx concentration.

• 한국광물학회:학술대회논문집
• /
• 한국암석학회.한국광물학회 2000년도 공동학술발표회 논문집
• /
• pp.19-19
• /
• 2000

;Ultramafic xenoliths found in alkali basalts from Jeju-do, Korea are mostly spinel Iherzolites composed of olivine, orthopyroxene, clinopyroxene and spinel. A subordinate amount of spinel harzburgites and pyroxenites are also found. Temperatures for these xenoliths were estimated from the compositions of coexisting pyroxenes (Wood '||'&'||' Banno 1973; Wells 1977; Bertrand '||'&'||' Mercier 1985; Brey '||'&'||' Kohler 1990), the AI-solubility in orthopyroxene coexisting with olivine and spinel (Sachtleben '||'&'||' Seck 1981; Webb '||'&'||' Wood 1986), and from Fe/Mg partitioning between olivine and spinel (Ballhaus et al. 1991). Temperature estimates from the thermometers by Wells (1977) and Brey and Kohler (1990) are compatible. Average equilibrium temperatures by these two methods for spinel peridotites range from 890 to 1030$^{\circ}$C. Pressures for spinel peridotites were estimated from the geobarometer by Kohler and Brey (1991) derived from the equilibrium Ca content of olivine coexisting with clinopyroxene, and fall within the range of 12.9 to 26.3 kbar. The combination of the thermometer by Brey and Kohler (1990) and the geobarometer by Kohler and Brey (1991) yields P- T estimates for Jeju-do spinel peridotites that fall in experimentally determined spinel lherzolite field in CFMASCr system (O'Neill 1981). These P-T data sets have been used to construct the Quaternary Jeju-do geotherm, which is significantly different from the conventional conductive geotherm. The xenolith-derived geotherm has a higher T gradient at low P (13 kbar) than at high P, which may be due to perturbation of the conductive heat flow by magma underplating or overplating at the crust-mantle boundary. Temperature estimates and statistics on the xenoliths indicate that the crust/mantle boundary in Jeju-do lies at about 11 kbar (~39 km). Spinellherzolite is inferred as a main constituent rock of the uppermost lithospheric mantle beneath Jeju-do. Pyroxenites were intercalated in peridotites in similar depth and temperature as re-equilibrated veins or lens.

• 한국광물학회지
• /
• 제13권3호
• /
• pp.147-163
• /
• 2000

The mineralogy and chemical composition of reddish to brownish yellow residual soils, so called "Hwangto" have been examined according to representative host rocks. The result of the study indicates that Hwangto consists of 40-80% clay minerals and various minerals such as quartz, feldspar, hornblende, goethite, and gibbsite. Clay minerals include kaolinite, halloysite, illite, hydroxy interlayered vermiculite (HIV), mica/vermiculite interstratifield mineral and chlorite. The mineralogical constituents and contents of Hwangto were different depending on the types of host rocks. Moreover, the Jurassic granitic rocks contain relatively more kaolin minerals, whereas the Cretaceous granitic rocks contain more HIV and illite. In addition, reddish Hwangto contains relatively more kaolinite and HIV, and yellowish Hwangto contains more illite and halloysite. It is suggested that feldspars and micas of host rocks were chemically weathered into illite, halloysite, illite/vermiculite interstratified minerals, and HIV, and finally into kaolinite. Compared with their host rocks, the major chemical compositions of Hwangto tend to contain more $Al_2O_3,\;Fe_2O_3,\;H_2O$ in amount and less Ca, Mg, and Na. Hwangto contains relatively high amount of trace elements, P, S, Zr, Sr, Ba, Rb, and Ce including considerable amount of Li, V, Cr, Zn, Co, Ni, Cu, Y, Nb, La, Nd, Pb, Th in excess of 10 ppm. Relatively high amount of most trace elements were detected in the Hwangto. The major and minor chemical compositions of the Hwangto were different depending on the types of host rocks. However, their difference was in the similar range compared with the compositions of host rocks.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.1
• /
• pp.46-49
• /
• 2003

Chemical mechanical polishing (CMP) is an essential dielectric planarization in multilayer microelectronic device fabrication. In the CMP process it is necessary to minimize the extent of surface defect formation while maintaining good planarity and optimal material removal rates. The polishing mechanism of W-CMP process has been reported as the repeated process of passive layer formation by oxidizer and abrasion action by slurry abrasives. Thus, it is important to understand the effect of oxidizer on W passivation layer, in order to obtain higher removal rate (RR) and very low non-uniformity (NU%) during W-CMP process. In this paper, we compared the effects of oxidizer or W-CMP process with three different kind of oxidizers with 5% hydrogen peroxide such as $Fe(NO_3)_3$, $H_2O_2$, and $KIO_3$. The difference in removal rate and roughness of W in stable and unstable slurries are believed to caused by modification in the mechanical behavior of $Al_3O_3$ particles in presence of surfactant stabilizing the slurry.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2017년도 춘계학술대회 논문집
• /
• pp.78-78
• /
• 2017

Pure Titanium and alloy have been widely used in dental implants and orthopedics due to their excellent mechanical properties, biocompatibility and corrosion resistance. However, due to the biologically inactive nature of Ti metal implants, it cannot bind to the living bone immediately after transplantation into the body. In order to improve the bone bonding ability of titanium implants, many attempts have been made to alter the structure, composition and chemical properties of titanium surfaces, including the deposition of bioactive coatings. The PEO method has the advantages of short experiment time and low cost. These advantages have attracted attention recently. Recently, many metal ions such as silicon, magnesium, zinc, strontium, and manganese have received attention in this field due to their impact on bone regeneration. Silicon (Si) in particular has been found to be essential for normal bone and cartilage growth and development. Zinc (Zn) plays very important roles in bone formation and immune system regulation and promotes bone metabolism and growth. Manganese (Mn) is an essential trace metal found in all tissues and is required for normal amino acid, lipid, protein and carbohydrate metabolism. The objective of this work was research on the corrosion behavior of Si, Zn and Mn-doped hydroxyapatite on the PEO-treated surface. Anodized alloys was prepared at 270V~300V voltage in the solution containig Zn, Si, and Mn ions. Ion release test was carried out using potentidynamic and AC impedance method in 0.9% NaCl solution. The surface characteristics of PEO treated Ti-6Al-4V alloy were investigated using XRD, FE-SEM, AFM and EDS.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2017년도 춘계학술대회 논문집
• /
• pp.152-152
• /
• 2017

Titanium and its alloys have been widely used for biomedical applications. However, the use of the Ti-6Al-4V alloy in biomaterial is then a subject of controversy because aluminum ions and vanadium oxide have potential detrimental influence on the human body due to vanadium and aluminum. Hence, recent works showed that the synthesis of new Ti-based alloys for implant application involves more biocompatible metallic alloying element,such as, Nb, Hf, Zr and Mo. In particular, Nb and Hf are one of the most effective Ti ${\beta}$-stabilizer and reducing the elastic modulus. Plasma electrolyte oxidation (PEO) is known as excellent method in the biocompatibility of biomaterial due to quickly coating time and controlled coating condition. The anodized oxide layer and diameter modulation of Ti alloys can be obtained function of improvement of cell adhesion. Silicon (Si) and magnesium (Mg) has a beneficial effect on bone. Si in particular has been found to be essential for normal bone and cartilage growth and development. In vitro studies have shown that Mg plays very important roles in essential for normal growth and metabolism of skeletal tissue in vertebrates and can be detected as minor constituents in teeth and bone. Therefore, in this study, Si and Mg coatings on the hydroxyapatite film formed Ti-29Nb-xHf alloys by plasma electrolyte oxidation has been investigated using several experimental techniques. Ti-29Nb-xHf (x= 0, 3, 7 and 15wt%, mass fraction) alloys were prepared Ti-29Nb-xHf alloys of containing Hf up from 0 wt% to 15 wt% were melted by using a vacuum furnace. Ti-29Nb-xHf alloys were homogenized for 2 hr at $1050^{\circ}C$. The electrolyte was Si and Mg ions containing calcium acetate monohydrate + calcium glycerophosphate at room temperature. The microstructure, phase and composition of Si and Mg coated oxide surface of Ti-29Nb-xHf alloys were examined by FE-SEM, EDS, and XRD.

• 한국건설순환자원학회논문집
• /
• 제2권2호
• /
• pp.158-165
• /
• 2014

연구에서는 BP부산물을 혼입한 알칼리활성 무시멘트 지반개량재의 사면안정 및 침투류 수치해석을 통하여 원지반토와 비교하여 개량토의 지반개량 효과를 검토하고자 하였다. 그 결과 사면안정해석을 실시한 결과에서는 건기시, 우기시 모두 건설공사 비탈면 설계기준(국토해양부, 2006)의 기준안전율을 만족하는 것으로 확인되었으며, 우기시 쏘일네일링으로 기준안전율을 만족하지 못하는 사면이 개량토로 보강하여 기준치를 만족한 것으로 나타났다. 또한 침투류 해석을 실시한 결과 개량토의 투수계수가 작아지는 것으로 나타났으며, 원지반토에 비하여 개량토로 표면보강된 경우는 포화심도가 낮아진 것으로 나타났다.

• 한국분말재료학회지
• /
• 제24권1호
• /
• pp.46-52
• /
• 2017

Fecralloy coating layer with large surface area is suitable for use as a filter media for efficient removal of hot gaseous pollutants exhausted from combustion processes. For uniform preparation of a Fecralloy coating layer with large surface area and strong adhesion to substrate, electrospray coating and thermal treatment processes are experimentally optimized in this study. A nano-colloidal solution with 0.05 wt% Fecralloy nanoparticles is successfully prepared. Optimized electrospraying conditions are experimentally discovered to prepare a uniform coating layer of Fecralloy nano-colloidal solution on a substrate. Drying the electrospray coated Fecralloy nano-colloidal solution layer at $120^{\circ}C$ and subsequent heating at $600^{\circ}C$ are the best post-treatment for enhancing the adhesion force and surface roughness of the Fecralloy coating layer on a substrate. An electrospray coating system, consisting of several multi-groove nozzles, is also experimentally confirmed as a reasonable device for uniform coating of Fecralloy nano-colloid on a large area substrate.

• 자원환경지질
• /
• 제12권2호
• /
• pp.79-93
• /
• 1979

한반도 내에 부존되고 있는 중적광상들은 세 주요한 Metallousenetic Epoch (Pre-Cambrian E., Jurassic-early Cretaceous E., 및 late Cretaceous-early Tertiary E.)에 생성되었고 성인으로 열수작용과 접촉교대작용에 기인된다고 보고되었다. 이중 12개 광상(달성, 산내, 일광, 상동, 대화, 월악, 복수, 옥방, 쌍전, 홍성, 삼봉, 청양)을 본 연구의 대상으로 택하고 각 지역에서 채취한 표품중 모두 25개 시료에 대하여 지화학적 실험을 수행하였다. 즉 각 분쇄된 시료 (-80+120mesh)는 super panner, 중액, isodynamic separator, UV lamp를 이용한 물리적인 처리과정을 거쳐 최종으로 입체현미경 하에서 단체분리된 후 Jarrell-Ash 1.5m Grating Spectrometer를 이용하여 본 연구대상 시료로 개발한 Spectrochemical method (Carrier: NaCl, Internal standard: $La_2O_3$)로 정량 분석되었다. 본 연구에서 밝혀낸 국내 회중석 광내에 함유되는 희유 윈소의 종류는 모두 Al, Bi, Fe, Si, Mn, Pb, Mg, Sn, Mo, Cu, Sr, Cr, Y, Ag, Ti, Ni, As, Yb의 18개 원소이며, 이들은 각각의 절대적 및 상대적인 함량과 각 광화작용의 시기, 광상의 성인, 모암, 각 원소의 mobility 그리고 회중석광의 형광색 및 육안색과 비교 검토되었다. 본 연구의 결과로 회중석광이 정출되는 과정에서 유사한 지질환경의 물리화학적인 여건이 이루어지면 그 내에 함유되는 몇 성분원소들의 화학적인 특성은 매우 유사성을 보여주는 typochemical habit를 가짐을 알 수 있었다. 본 연구에서 밝혀진 한국산 회중석 광내의 희유성분(稀有成分)으로서 Y, Mn, Sr 원소들의 Geochemical mobility의 특성(特性)은 앞으로 회중석광의 심도탐광을 위하여 고려되어야하고, 더욱 연구개발되어야 할 것이다. 또한 상기 회중석 광내의 물리적 및 화학적으로 결합되어 있는 불순물의 희유성분들은 선광 제련 파정에서 금속성분의 추출농집공정(工程)에 유용한 자료가 될 것이다.

• 한국염색가공학회지
• /
• 제22권3호
• /
• pp.194-206
• /
• 2010

This study was carried out to identify the optimum dyeing conditions for maximum dye uptake of Prunus yedoensis Matsumura flower extract on silk fabric and to investigate hue/tone characteristics and fastness properties of the dyed fabrics. As results, the flower extract was found to contain flavonoids by FT-IR and to show yellowish shade by UV-vis spectrum. Silk fabric was optimized for maximum dye uptake to five repetitions of dyeing at $80^{\circ}C$ for 60 min with an extract concentration of 600% owf in terms of both K/S and color differences. Pre-mordanting was more effective to dye uptake than post-mordanting for all of the mordants used. Un-mordanted and pre-mordanted fabric showed YR(Yellow Red) while most of post-mordanted ones did Y(Yellow). Main tones of dyed fabrics were sf(soft) and lt(light) in the case of unmordanting or Al-mordanting whereas they were d(dull) and g(grayish) by post-mordanting with Cu, Cr, and Fe, respectively. The fastness grades to rub and dry cleaning were reasonably good for most dyeing conditions while those to light were poor. Finally dyeing condition for each hue/tone of the dyed silk with the flower extract was optimized considering fastness properties.