• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.4
• /
• pp.127-134
• /
• 2021

In this study, the adhesive fracturing characteristics of a DCB specimen due to single and heterogeneous bonding materials under tearing load was investigated. The experiments were conducted to examine the fracturing properties of the adhesive DCB specimen. As an experimental condition, a forced displacement of 3mm/min was applied to one side while the other side was fixed. As a result of the experiment, it was found that the AL6061-T6 material was superior to the CFRP material in terms of maximum stress, specific strength, and energy release rate when compared to the adhesive fracturing property of a single material. We tested CFRP-AL, a heterogeneous bonding material, and compared its experimental results to the results from the single materials. Based on these results, CFRP-AL with a heterogeneous bonding material was observed to have the superior structural safety compared to single materials for the mode III fracture type.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.2
• /
• pp.7-13
• /
• 2019

This study aims to develop a FE Model to simulate dissimilar friction stir welding and to address its potential for fundamental analysis and practical applications. The FE model is based on Coupled Eulerian-Lagrangian approach. Multiphysics systems are calculated using explicit time integration algorithm, and heat generations by friction and inelastic heat conversion as well as heat transfer through the bottom surface are included. Using the developed model, friction stir welding between an Al6061T6 plate and an AZ61 plate were simulated. Three simulations are carried out varying the welding parameters. The model is capable of predicting the temperature and plastic strain fields and the distribution of void. The simulation results showed that temperature was generally greater in Mg plates and that, as a rotation speed increase, not the maximum temperature of Mg plate increased, but did the temperature of Al plate. In addition, the model could predict flash defects, however, the prediction of void near the welding tool was not satisfactory. Since the model includes the complex physics closely occurring during FSW, the model possibly analyze a lot of phenomena hard to discovered by experiments. However, practical applications may be limited due to huge simulation time.

• Journal of Welding and Joining
• /
• v.34 no.3
• /
• pp.23-30
• /
• 2016

This paper discusses the optimization of friction stir spot welding (FSSW) process parameters for joining Aluminum alloy (AA6061-T6) with Magnesium alloy (AZ31B) sheets. Prior to optimization an empirical relationship was developed to predict the Tensile Shear Fracture Load (TSFL) incorporating the four most important FSSW parameters, i.e., tool rotational speed, plunge rate, dwell time and tool diameter ratio, using response surface methodology (RSM). The experiments were conducted based on four factor, five levels central composite rotatable design (CCD) matrix. The maximum TSFL obtained was 3.61kN, with the tool rotation of 1000 rpm, plunge rate of 16 mm/min, dwell time of 5 sec and tool diameter ratio of 2.5.

• The Bulletin of The Korean Astronomical Society
• /
• v.37 no.2
• /
• pp.215.1-215.1
• /
• 2012

일반적인 천체 망원경의 반사경은 유리재질의 소재를 원하는 형상의 반사면으로 가공한 후 그 위에 알루미늄 코팅을 하여 사용한다. 하지만 본 연구에 사용된 망원경은 주경과 부경을 모두 알루미늄(Al-6061 T6)을 직접 가공하여 제작하였다. 알루미늄을 직접 가공하여 반사경을 만들 경우의 장점은 냉각이 필요한 기기에서 광구조물과 반사경의 열팽창 계수 차이를 신경 쓸 필요가 없으며 DTM(Diamond Turning Machine)을 이용할 수 있다는 것이다. 본 망원경은 망원경의 성능을 향상시키기 위하여 3매의 보정 렌즈를 사용한 반사굴절 망원경이며 구경은 200mm, 초점거리는 750mm, F수는 3.75이다. 주경과 부경은 각각 200 mm와 90 mm의 쌍곡면으로 설계 및 제작되었다. 본 연구에서는 DTM을 이용해 알루미늄 재질의 주경과 부경을 제작하고 이 반사경들의 측정 결과를 토대로 측정 결과와의 오차가 가장 작은 새로운 반사경 설계식을 유도하였다. 이 설계식을 이용하여 광학 설계 프로그램에서 망원경의 성능을 예측하였으며 실제 제작된 망원경을 이용하여 얻은 이미지와 비교한다.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.5
• /
• pp.70-75
• /
• 2018

This study analyzes the change of Al 6061-T6 specimen surface shape when undergoing microparticle spraying and analyzes the influence of factors on the experiment. Fine particle spraying is applied to the specimen and the surface shape of the processed surface is measured through a surface shape measuring device. The measured data was analyzed by the ANOVA method to investigate the effect of factors such as particle, nozzle diameter, pressure, injection height, and injection time on the injection depth and injection diameter.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.5
• /
• pp.122-130
• /
• 1996

In this study, machinability of some aluminum-magnesium alloy are experimentally investigated using polycrystalline diamond tool with turning, and evaluated some independent cutting variables affected micrometal cutting characteristics as cutting force, specific cutting resistance, shear angles. To know the effect of cutting parameters of single point diamond machining, experiments were performed to measure cutting forces for high speed turning of aluminum alloy 6061-T6, SM45C and FC20 with poly- crystalline diamond and coated cemented carbide tool. Independent cutting variables were changed to a variety of cutting speed, feed rate, rake angles, material properties of workpiece and tool. Futhermore. Some useful informations are obtained in this study can guide micro metal cutting of aluminum alloy with diamond tool.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.145-148
• /
• 2006

Cold gas dynamic spray is a relatively new coating process by which coatings can be produced without significant heating during the process. Cold gas dynamic spray is conducted by powder sprayed by supersonic gas jet, and generally called the kinetic spray or cold-spray. Cold-spray was developed in Russia in the early 1980s to overcome the defect of thermal spray method. Its low process temperature can minimize thermal stress and also reduce the deformation of the substrate. Most researches on cold-spray have focused on micro scale coating, but our research team tried to apply this method to macro scale deposition. The macro scale deposition causes deformation of a thin substrate which is usually convex to the deposited side. In this research, the main cause of the deformation was investigated using 6061-T6 aluminum alloy and properties of deposited aluminum layer such as coefficient of thermal expansion, Elastic modulus, hardness, electric conductivity were measured. From the result of the analysis, it was concluded that compressive residual stress was the main reason of substrate deformation while CTE had little effect.

• Transactions of Materials Processing
• /
• v.27 no.6
• /
• pp.331-338
• /
• 2018

Electrohydraulic forming (EHF) process is a high speed forming process that utilizes the electric energy discharge in fluid-filled chamber to deform a sheet material. This process is completed in a very short time of less than 1ms. Therefore, finite element analysis is essential to observe the deformation mechanism of the material in detail. In addition, to perform the numerical simulation of EHF, the material properties obtained from the high-speed status, not quasi static conditions, should be applied. In this study, to obtain the parameters in the constitutive equation of Al 6061-T6 at high strain rate condition, a surrogate model using an artificial neural network (ANN) technique was employed. Using the results of the numerical simulation with free-bulging die in LS-DYNA, the surrogate model was constructed by ANN technique. By comparing the z-displacement with respect to the x-axis position in the experiment with the z-displacement in the ANN model, the parameters for the smallest error are obtained. Finally, the acquired parameters were validated by comparing the results of the finite element analysis, the ANN model and the experiment.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.12
• /
• pp.2091-2099
• /
• 2001

Fatigue crack growth behavior of inclined cracked Al 6061-T6 thick aluminum plate(6mm) repaired with the bonded composite patch was studied. A 0°inclined crack bonded reinforced composite patch and 15°, 30°, 45°, 60°inclined crack plates were tested. The effect of patch and inclined angle were studied and compared to each other. Also we investigated to the crack propagation direction and debonding behavior during the fatigue crack growth test. In this paper. a study was con(ducted to get an fatigue life, fatigue crack growth ratio and crack growth direction. Finally, the effectiveness of composite patch on inclined cracked plate was investigated. The results demonstrated thats there was a definite variation in fatigue life and fatigue crack growth behavior depending on the inclined crack angle.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.4
• /
• pp.483-490
• /
• 2013

In aluminum sheet metal forming, the conventional forming methods of T4 or T6 heat-treated sheets result in low formability and dimensional accuracy. This study suggests a new forming method for aluminum sheets called as hot forming quenching (HFQ) that solves the problems faced in the conventional method. HFQ combines the heat treatment and forming processes through the forming die during the quenching of a solid solution. To evaluate the application of HFQ to the sheet forming of aluminum, an Erichsen and V-bending test are performed in this study to measure the dimensional accuracy and formability, which are then compared with those of the conventional forming method. Furthermore, the strength and hardness of the products formed by HFQ are measured to confirm the degradation in mechanical properties compared with the conventional forming method, which shows the validity of the application of HFQ to aluminum sheet metal forming.