• 한국전산유체공학회지
• /
• 제18권4호
• /
• pp.41-46
• /
• 2013

The selection of the optimal position of the flap was performed in order to improve the aerodynamic performance during the take-off and landing processes of aircraft. For this, the existing airfoils of the main wing and flap are selected as the baseline model and the lift coefficients (cl) according to angle of attacks (AOA) were calculated with the change of the position of flap airfoil. The objective function was defined as the consideration of the maximum cl, lift to drag ratio and cl at certain AOA. Then, at 121 experimental points within $20mm{\times}20mm$ domain, two dimensional flow simulations with Spalart-Allmaras turbulence model were performed concerning the AOA from 0 to 15 degree. If the optimal position was located at the domain boundary, the domain moved to the optimal position. These processes were iterated until the position was included in the inside of the domain. From these processes, the flow separation at low AOA was removed and cl increased linearly comparing with that of the baseline model.

• 한국태양에너지학회 논문집
• /
• 제23권3호
• /
• pp.55-61
• /
• 2003

This paper represents the effect of rotor geometry on the performance of a small-scale Wells turbine for wave energy conversion. In this study, four kinds of blade profile were selected from previous studies with regard to the blade profile of the Wells turbine. The experimental investigations have been performed for two solidities by model testing under steady flow conditions, and then the effect of blade profile on the running and starting characteristics under sinusoidal flow conditions have been investigated by a numerical simulation using a quasi-steady analysis. In addition, the effect of sweep on the turbine characteristics has been investigated for the cases of CA9 and HSIM 15-262123-1576. As a result, a suitable choice of these design factors has been suggested.

• 한국태양에너지학회 논문집
• /
• 제23권2호
• /
• pp.99-105
• /
• 2003

This paper presents the effect of rotor geometry on the performance of a small-scale Wells turbine for wave energy conversion. In this study, four kinds the Wells turbine of blade profile were selected from previous studies. The types of blade profile included in the papers are as follows: NACA0020 ; NACA0015; CA9; and HSIM 15-262123-1576. The experimental investigations have been performed for two solidities by testing model under steady flow conditions. The effect of blade profile on the running and starting characteristics under sinusoidal flow conditions have also been investigated by a numerical simulation based on a quasi-steady analysis. In addition, the effect of sweep on the turbine characteristics has been studied for the cases of CA9 and HSIM 15-262123-1576. Based on the evaluation, a suitable choice of these design factors has been suggested. As a result, it seems that a suitable choice of the sweep ratio of 0.35 for the blade profile of the Wells turbine.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제10권2호
• /
• pp.97-105
• /
• 2002

A centrifugal water chiller using alternative refrigerant R134a has been developed. The prototype was designed to have refrigerating capacity of 300RT. Its compressor employs a single high-speed impeller, airfoil diffuser and collector. Newly developed, enhanced tubes were installed in the evaporator and the condenser to reduce the required head for the compressor. Off-design characteristics at various conditions, performance test of the compressor and analysis of the refrigeration cycle were performed. So the probability of use in part load condition was checked and the direction for revision was suggested.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.179.2-179.2
• /
• 2010

In this study, we have constructed the method of design about H-Darrieus wind turbine, a kind of VAWT(vertical axis wind turbine). The NACA 0012 airfoil is chosen for the blade, and DMS(double multiple streamtube) theory is used for the analysis. The flow field is computed with numerical solution of rotating Navier-Stokes equations. From the result of experimental data of power coefficient curves, the validity of the present research is checked. Through the non-dimensional parameter analysis for the wind turbine design, we estimated the efficiency of wind turbine with the resultant Cp's, with which an efficient design of VAWT is achieved, and aerodynamic characteristics are presented systematically.

• 한국항공우주학회지
• /
• 제32권10호
• /
• pp.20-27
• /
• 2004

본 논문에서는 CRW 무인 항공기에 사용되는 타원익형과 전기체의 공력해석 및 동체와 로터를 연결하는 허브주위의 공기역학적 현상에 대한 분석을 수행하였고 허브로 인한 항력 증가를 감소할 수 있는 방안을 모색하였다. 또한 항력 감소를 위해 제안한 fairing 장착방법을 풍동시험을 통해 그 효과를 확인하였다.

• 한국해양공학회지
• /
• 제9권2호
• /
• pp.75-82
• /
• 1995

The free surface effects on the aerodynamic performance of 2-D wings are investigated based on the potential flow approximation. The wing is represented b source and vortex distributions on the wing surface. The steady free surface effect is taken into account by source distribution on the free surface and the velocity potentials of air and water flows are obtained. Using three different techniques, namely, positive image method, inverse image method and source distribution method, numerical results are obtained for wave elevation, pressure distribution and lift coefficient with various foil sections. The wave elevation calculated by the inverse image method is shown to be very small even at higher speeds so that the free surface effect on the performance of wings is regraded negligible. However, the wave elevations by the positive image method and source distribution method are relatively high at higher speeds and accordingly the free surface effects on wings can not be neglected.

• 한국전산유체공학회지
• /
• 제16권4호
• /
• pp.72-83
• /
• 2011

A high-order discontinuous Galerkin method for the two-dimensional compressible Navier-Stokes equations was developed on unstructured triangular meshes. For this purpose, the BR2 methd(the second Bassi and Rebay discretization) was adopted for space discretization and an implicit Euler backward method was used for time integration. Numerical tests were conducted to estimate the convergence order of the numerical solutions of the Poiseuille flow for which analytic solutions are available for comparison. Also, the flows around a flat plate, a 2-D circular cylinder, and an NACA0012 airfoil were numerically simulated. The numerical results showed that the present implicit discontinuous Galerkin method is an efficient method to obtain very accurate numerical solutions of the compressible Navier-Stokes equations on unstructured meshes.

• 한국유체기계학회 논문집
• /
• 제13권2호
• /
• pp.59-64
• /
• 2010

A design method of Sirocco fan is developed for constructing 3-D impeller and scroll geometries, and for predicting both the aerodynamic performance and the noise characteristics of the designed fan. The aerodynamic blading design of fan is conducted by blade angle, camber line determinations and airfoil thickness distribution, and then the scroll geometry of fan is designed by using logarithmic spiral. The aerodynamic performance of designed fan is predicted by the meanline analysis with flow blockage, slip and pressure loss correlations. Based on the predicted performance data, fan noise is predicted by two models for cutoff frequency and broadband noise sources. The present predictions for the performance and the noise level of actual fans are well agreed with measurement results.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2003년도 The Fifth Asian Computational Fluid Dynamics Conference
• /
• pp.291-293
• /
• 2003

This paper deals with a thrust generation of flapping-airfoil by dynamic stall. From many other previous research results, phase angle $ between pitching and plunging mode of flapping motion must be 90 deg. to satisfy maximum propulsive efficiency. In this case, leading edge vortex is relatively small. This phenomenon is related dynamic stall. So preventing leading edge vortex induced by dynamic stall guarantees maximum propulsive efficiency. But, in this paper we insist the leading edge vortex yields quite a positive influence on thrust generation and propulsive efficiency. In order to certify our opinion, pitching and plunging motions were calculated with the parameter of amplitude and frequency by using the unsteady, incompressible Navier-Stokes flow solver with a two-equation turbulence model. For more efficient computation, it is parallelized by MPI programming method.