• Journal of computational fluids engineering
• /
• v.19 no.2
• /
• pp.8-16
• /
• 2014

Two-dimensional prediction capability of several analysis codes, such as XFOIL, MSES, and KFLOW, is compared and analyzed based on computational results of airfoil flows. To this end the transition transport equations are coupled with the Navier-Stokes equations for the prediction of the natural transition and the separation-induced transition. Experimental data of aerodynamic coefficients are used for comparison with numerical results for the transitional flows. Numerical predictions using the transition transport model show a good agreement with experimental data. Discrepancies have been found in the prediction of the pressure drag are mainly caused by the difference in the far-field circulation correction methods.

• Proceeding of EDISON Challenge
• /
• 2012.04a
• /
• pp.53-56
• /
• 2012

항공기에 작용하는 공기역학적 힘인 양력과 항력은 항공기 날개 설계에서 성능을 좌우하는 성능지수로 주로 이용된다. 본 연구에서는 NACA0012 airfoil 모델의 공력특성을 EDISON 열유체 시뮬레이션 프로그램(이하 EDISON)을 이용해 분석하고 검증해 보았다. 아음속 유동의 특정 조건에서 받음각과 유동형태에 따른 공력특성 분석을 수행하여 받음각에 따라 변하는 양력계수, 항력계수, 양항비, 실속각과 천음속 유동 조건에 맞추어진 마하수 0.5~1.22 영역에서 변하는 항력계수를 기존 데이터와 비교 검증했다.

• International Journal of Aeronautical and Space Sciences
• /
• v.14 no.3
• /
• pp.210-214
• /
• 2013

The sensitivity of transonic flow past a Whitcomb airfoil to deflections of an aileron is studied at free-stream Mach numbers from 0.81 to 0.86 and vanishing or negative angles of attack. Solutions of the Reynolds-averaged Navier-Stokes equations are obtained with a finite-volume solver using the $k-{\omega}$ SST turbulence model. The numerical study demonstrates the existence of narrow bands of the Mach number and aileron deflection angles that admit abrupt changes of the lift coefficient at small perturbations. In addition, computations reveal free-stream conditions in which the lift coefficient is independent of aileron deflections of up to 5 degrees. The anomalous behavior of the lift is explained by interplay of local supersonic regions on the airfoil. Both stationary and impulse changes of the aileron position are considered.

• 한국전산유체공학회:학술대회논문집
• /
• 1999.05a
• /
• pp.171-176
• /
• 1999

In the present paper, three types of the flow solvers were used to investigate the influence on the airfoil shape optimization. The adopted equations, i.e., Euler , thin layer Navier- Stokes and full Navier-Stokes ones, are solved using implicit LU-ADI decomposition scheme. The feasible direction algorithm with the sinusoidal function was used as an optimization algorithm. The present numerical method was applied to the drag minimization problems under the initial shape of NACA0012 airfoils.

• Journal of Mechanical Science and Technology
• /
• v.20 no.8
• /
• pp.1248-1255
• /
• 2006

The velocity and pressure fields of a ship's propulsion mechanism of the Weis-Fogh type, in which a airfoil moves reciprocally in a channel, are studied in this paper using the advanced vortex method. The airfoil and the channel are approximated by a finite number of source and vortex panels, and the free vortices are introduced from the body surfaces. The viscous diffusion of fluid is represented using the core-spreading model to the discrete vortices. The velocity is calculated on the basis of the generalized Biot-Savart law and the pressure field is calculated from integrating the equation given by the instantaneous velocity and vorticity fields. Two-dimensional unsteady viscose flows of this propulsion mechanism are numerically clarified, and the calculated results agree well with the experimental ones.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.5
• /
• pp.321-327
• /
• 2016

This paper presents the application of airfoil impeller for enhancement of aerodynamic performance of a high speed centrifugal fan. Three airfoil impellers are proposed, considering the maximum thickness and the location of maximum thickness of the airfoil. C4 airfoil thickness distribution is applied to the three airfoil impellers. The impellers are evaluated using CFD (computational fluid dynamics) and suction power test. From the results, it is confirmed that flow separations on the pressure side of the impeller blades and the pressure side of diffuser blades are reduced when airfoil blade is applied to the impellers. It is also confirmed that with the centrifugal fan having airfoil impellers, there is an increase in fan efficiency by approximately 3% and reduction in specific sound level by approximately 1.3 dB(A).

• Journal of Mechanical Science and Technology
• /
• v.14 no.2
• /
• pp.226-235
• /
• 2000

The performance prediction of an airfoil fan using a commerical code, STAR/CD, is verified by comparing the calculated results with measured performance data and velocity fields of an airfoil fan. The effects of inlet tip clearance on performance are investigated. The calculations overestimate the pressure rise performance by about 10-25 percent. However, the performance reduction due to tip clearance is well predicted by numerical simulations. Main source of performance decrease is not only the slip factor but also impeller efficiency. The reduction in performance is 12-16 percent for 1 percent gap of the diameter. The calculated reductions in impeller efficiency and slip factor are also linearly proportional to the gap size. The span-wise distributions of phase averaged velocity and pressure at the impeller exit are strongly influenced by the radial gap size. The radial component of velocity and the flow angle increase over the passsage as the gap increases. The slip factor decreases and the loss increases with the gap size. The high velocity of leakage jet affects the impeller inlet and passage flows. With a larger clearance, the main stream moves to the impeller hub side and high loss region extends from the shroud to the hub.

• Wind and Structures
• /
• v.32 no.3
• /
• pp.239-248
• /
• 2021

In this study, three airfoil families, NACA, FX and S, in each case three from each series with different shapes were investigated at different angles of attack using Computational Fluid Dynamics (CFD) method. To verify the CFD model, simulation results of the NACA 0012 airfoil was compared against the available experimental data and k-ω SST was used as the turbulence model. Lift coefficients, lift to drag ratios and pressure distributions around airfoils were obtained from the CFD simulations and compared each other. The simulations were performed at three Reynolds numbers, Re=2×105, 1×106and 2×106, and angle of attack was varied between -6 and 12 degrees. According to the results, similar lift coefficient values were obtained for symmetric airfoils reaching their maximum values at similar angles of attack. Maximum lift coefficients were obtained for FX 60-157 and S 4110 airfoils having lift coefficient values around 1.5 at Re=1×106 and 12 degrees of angle of attack. Flow separation occurred close to the leading edge of some airfoils at higher angles of attack, while some other airfoils were more successful in keeping the flow attached on the surface.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.615-620
• /
• 2000

Manoeuvrability of ships has been receiving a great deal of attention both concerning navigation safety and the prediction of ship manoeuvring characteristics, especially at the preliminary design stage. Recently, in order to improve manoeuvrability of ships, High-lift devices could be applied to design of rudder at design stage. Now, among the them, we carried out the flow visualization and investigation of flow field around a flapped rudder(trailing-edge flap). A trailing-edge flap is simply a portion of the trailing-edge section of airfoil that is hinged and which can be deflected upward or downward. Flow visualization results of flap defection shown as follow Photos including main body and flap defection.

• Journal of computational fluids engineering
• /
• v.17 no.2
• /
• pp.1-10
• /
• 2012

This paper presents the numerical simulation results of heat transfer and friction loss for a rotating two-pass duct with the airfoil-guide vanes in the turning region. The Kriging model is used as an optimization technique with Reynolds-averaged Navier-Stokes analysis of flow field and heat transfer with shear stress transport turbulent model. To improve the heat transfer performance, angle and location of the airfoil-guide vanes have been selected as design variables. The optimization problem has been defined as a minimization of the objective function, which is defined as a linear combination of heat transfer related term and friction loss related term with a weight factor. The airfoil-guide vanes in the turning region keep the high level of heat transfer while the friction loss has a low value. By comparing the presence or absence of airfoil-guide vanes, it is shown that the airfoil-guide vanes exhibited the best heat transfer performance to improve the blade cooling except the first passage.