• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.5
• /
• pp.89-95
• /
• 2018

In this paper, we analyze the antenna performance changes caused by the aircraft structure, diffraction and reflection, when the direction finding antenna used in the aircraft is mounted on the aircraft. Direction finding antenna is an antenna that receives radar threat signal in the direction finding device of aircraft electronic warfare system. Recently, because various antenna are mounted on an aircraft, various analyzes such as antenna performance and interference analysis are required. Therefore, the electromagnetic analysis was carried out by installing a broadband direction finding antenna with 50% bandwidth on simulated aircraft, and the direction finding performance was analyzed by comparing the single antenna performance with the performance mounted on the aircraft. The analyzed direction finding accuracy was $6.47^{\circ}$ RMS and predicted to be suitable as an antenna for aircraft direction finding antenna.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.3
• /
• pp.451-456
• /
• 2020

In this paper, we studied the method of designing a embedded antenna for mounting on the JTDLS complete aircraft. The proposed antenna satisfies the MIDS-LVT operation frequency band and is designed as a broadband in consideration of expandability. As a result of the design, it was confirmed that the proposed antenna has similar electrical performance to the existing blade antenna and has broadband characteristics. As a result of EM analysis, the antenna was mounted on the top and bottom parts of the aircraft to check the mount of the aircraft, and it was confirmed that both the top and bottom parts had good radiation characteristics. The technology acquired through this study is judged to be applicable to the JTDLS completed aircraft.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.11
• /
• pp.1037-1043
• /
• 2004

In this paper, a new fault detection and isolation algorithm fur inertial sensor system is proposed. To identify the inertial sensor fault, single antenna GPS receiver is used as an effective redundancy source. To use GPS receiver as redundancy for the inertial sensors, the algorithm to estimate the attitude and acceleration using single antenna GPS receiver is adopted. By using Doppler shift of carrier phase signal and kinetic characteristics of aircraft, attitude information of aircraft can be obtained at the coordinated flight condition. Based on this idea, fault diagnosis algorithm for inertial sensors using single antenna GPS based attitude is proposed. For more effective FDI, decision variables considering the aircraft maneuver are proposed. The effectiveness of the proposed algorithm is verified through the numerical simulations.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.3 s.106
• /
• pp.295-306
• /
• 2006

In this paper, we proposed and implemented a novel antenna cover mounted over a microstrip path antenna for ultrafast aircraft. A protective antenna cover prevents alteration in the electrical characteristics of the antenna due to environmental conditions. The permittivity of the cover materials should be practically invariable at all operating frequencies. We evaluated the characteristics of the antenna with both simulation and experiment. The experimental results show that the proposed antenna cover can be useful for ultrafast aircraft.

• Composites Research
• /
• v.37 no.1
• /
• pp.53-57
• /
• 2024

Numerous studies have explored structural antennas for integrating advanced wireless systems into aircraft without altering their external form. However, much of the research on structural antennas has focused on patch antennas, which are characterized by limitations such as narrow frequency bands and low directivity. In contrast, the Vivaldi antenna, widely utilized in wireless applications, offers the advantages of a wide frequency band and high directivity. Nevertheless, its application to aircraft has been challenging due to radiation direction constraints. In this study, we endeavor to address this issue by proposing the application of the antenna patch onto the honeycomb wall, thus enabling the use of the Vivaldi antenna on aircraft. The impact of the honeycomb structure on antenna radiation performance was analyzed, and the potential of the honeycomb Vivaldi antenna was validated through simulation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.2
• /
• pp.131-139
• /
• 2011

In this paper, we propose a double-faced window printed antenna for aircraft applications. The proposed antenna structure consists of a feeding line and a multi-loop radiator located on different sides of the window to use the limited given-area effectively. The proposed antenna is optimized by the genetic algorithm in conjunction with the FEKO EM simulator. The optimized antenna is built and installed on a 1/10 sized KUH-Surion mock-up and antenna performances such as the reflection coefficient and the radiation patterns are measured. The optimized antenna shows a half power matching bandwidth of about 33 % at 60 MHz and an average bore-sight gain of about -3.49 dBi. To verify the reception capability of the optimized antenna, we simulated the received power according to a flight scenario. The result confirms that the optimized antenna shows a minimum received power level above -60 dBm at a range of 200 km, which is similar to the pole antenna that is currently used as a FM voice antenna for KUH-Surion.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.8
• /
• pp.766-773
• /
• 2016

This paper proposes an aircraft-installed compact offset-parabolic-reflector antenna for the spinning direction-finding applications. The feeder of the reflector antenna is a LPDA antenna that has the ultra-wideband characteristics and the $45^{\circ}$ slant linear polarization. The reflector is designed to be slanted by $5^{\circ}$ in the elevation and to be small in size on the basis of the reference parabolic shape for the purpose of the high gain and mounting on the underside of aircraft fuselage. Over the ultra-wideband 20:1 bandwidth from S to Ka band, the measured average gain of the proposed antenna is 27.97 dBi, and the average half-power beam width is $4.55^{\circ}$ in the azimuth and $4.3^{\circ}$ in the elevation which is the pencil-beam radiation pattern. All the measured data are similar to the simulation results. The designed compact offset-parabolic-reflector antenna that is installed in the limited area has the ultra-wideband and high-gain characteristics. We expect that the newly designed antenna can be applied to the spinning direction-finding antenna system installed in an aircraft.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.7
• /
• pp.567-575
• /
• 2014

This paper suggests an installation procedure of a smart skin prototype into an aircraft, flight demonstration test procedures and test results. Four communication and navigation antennas are embedded into one Conformal Load-bearing Antenna Structure(CLAS). Log periodic patch type antenna was designed as a multi-band antenna to cover four antenna frequency bands. The requirements of CLAS were verified by ground tests before aircraft installation. A CLAS speed-brake was installed into KT-1 aircraft and performances of dual antennas were verified as multi-antenna tests on the ground. Electromagnetic compatibility tests were conducted to check compatibility between the CLAS and all existing equipments. Flight demonstration tests were conducted by one sortie of flight test for one antenna. The activeness and continuity of communication and navigation signal during the flight, null area of antenna signal along the circling flight were monitored. The embedded antennas worked better than expected during four sorties of flight tests.

• Journal of Aerospace System Engineering
• /
• v.15 no.5
• /
• pp.106-112
• /
• 2021

In this study, we performed a design and structural analysis of a blade-shaped antenna installation on the rear fuselage of a rotary wing aircraft operated by the military. When the structure is damaged while the aircraft is in operation, it is separated from the aircraft main structure and may collide with the rotor or blades to cause the aircraft to crash. Therefore, structural safety for the modified structure must be secured. The design requirement for the newly installed modified part were established, and the load condition was constructed by applying the load that may occur in the aircraft after the modification. Structure safety for the modified structure was secured by performing structure analysis. To analysis stress and deformation of aircraft structure, we developed finite element model and verified it by using hand calculation method. We confirmed the safety of the modified structure through the final structural integrity analysis.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.10
• /
• pp.951-957
• /
• 2013

In this paper, we propose a performance evaluation process of aircraft blade antennas. The process consists of various sub-processes that should be considered for a stable communication link with the base station. The process begins with the settlement of the ground shape and size to evaluate the impedance matching characteristics of a stand-alone antenna. Next, the main communications area of the antenna is determined by considering a flight scenario, and then the minimum gain requirements of the antenna are derived in the operating frequency band. Finally, the proposed evaluation process is applied for a commercial aircraft blade antenna. The results demonstrate that the proposed process is suitable to be adopted for the evaluation of aircraft blade antennas.