• Journal of Advanced Marine Engineering and Technology
• /
• 제38권9호
• /
• pp.1064-1069
• /
• 2014

에멀젼연료(Emulsified fuel)와 EGR(Exhaust Gas Recirculation)는 디젤엔진으로부터 발생하는 NOx를 저감시키는 효과적인 방법들이다. 일반적으로, EGR 방법은 열적, 화학적 그리고 희석효과의 세 가지 다른 경로에 의하여 디젤 엔진의 연소에 영향을 미치는 것으로 알려져 있다. 그중 특히 열적효과는 흡기 중의 이산화탄소와 수분에 의한 열용량의 증가와 관련되어 있다. 한편, 물의 증발열과 마이크로 폭발(Micro-explosion)을 이용하는 에멀젼연료는 디젤엔진의 배기 배출물을 저감시키는 효과적인 방법으로 인식되어 왔다. 본 연구에서 저자는 함수율 20%의 에멀젼연료와 EGR율 30%의 사용에 의한 연소와 배기 배출물 특성에 대하여 연구하였다. 그리고 연료 분사 패턴 제어의 효과에 대하여 조사하였다.

• 한국자동차공학회논문집
• /
• 제14권5호
• /
• pp.32-38
• /
• 2006

Currently, due to the serious world-wide air pollution by substances emitted from vehicles, emission control is enforced more firmly and it is expected that the regulation requirements for emission will become more severe. A new concept combustion technology that can reduce the NOx and PM in relation to combustion is urgently required. Due to such social requirement, technologically advanced countries are making efforts to develop an environment-friendly vehicle engine at the nation-wide level in order to respond to the reinforced emission control. As a core combustion technology among new combustion technologies for the next generation engine, the homogenous charge compression ignition(HCCI) is expanding its application range by adopting multiple combustion mode, catalyst, direct fuel injection and partially premixed combustion. This study used a 2-staged injection method in order to apply the HCCI combustion method without significantly altering engine specifications in the aspect of multiple combustion mode and practicality by referring to the results of studies on the HCCI engine. In addition, this study confirmed the possibility of securing optimum fuel economy emission reduction in the IMEP 8bar range(which could not be achieved with existing partially premixed combustion) through forced charging, exhaust gas recirculation(EGR), compression ratio change and application of DOC catalyst.

• 대한기계학회논문집B
• /
• 제24권2호
• /
• pp.161-168
• /
• 2000

Lean combustion in a SI engine is one of the best solution for the improvement of fuel economy and reduction of pollutant emission. In order to access a lean combustion engine, stable combustion at lean AlF ratio is needed. In this paper, the effect of fuel injection timing on lean misfire limit has been investigated in an MPI engine. To investigate the interaction of injection timing and intake flow characteristics, three different swirl generating SCV(swirl control valve) configurations were considered, and investigated their effects on lean misfire limit and torque at full load operation. Also the effects of spark timing on lean combustion has been investigated. Lean combustion has been examined and the results are reported in this paper. SCV B has been developed to satisfy the requirements of sufficient swirl generation to improve lean combustion and stable performance. It is found that injection timing, spark timing and intake air motion govern the stable lean combustion.

• 전기화학회지
• /
• 제13권3호
• /
• pp.193-197
• /
• 2010

In terms of the system efficiency, it is very useful to apply the ejector into the fuel recirculation system of a fuel cell system since the ejector needs no parasitic power to operate. Since the conventional automotive fuel cell use hydrogen and air as their fuel, the only hydrogen is needed to be recirculated for the better fuel efficiency. On the other hand, the submarine fuel cell needs both hydrogen and oxygen recirculation systems because the submarine drives under the sea. In particular, the cathodic recirculation has to meet the tougher target since the oxygen based pressurized stack generally used in the submarine applications generates the significant amount of the water in the stack during the operation. Namely, the oxygen utilization has designed less than 50% in the whole operating range for the better exhausting of the generated waters. And thereby in terms of the oxygen utilization, the entrainment ratio of the ejector should be more than 1 within the whole operating range. However, the conventional ejector using a constant nozzle can not afford to satisfy the mentioned critical requirement. To overcome the problem, the dual-ejector and its control strategy are designed. The performance of the proposed dual-ejector is verified by the experiments based on the real operating conditions of the target submarine system. Furthermore, the proposed design method can be used for the other fuel recirculation system of a large-scale fuel cell system with the critical requirement of the fuel utilization.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2002년도 ICCAS
• /
• pp.68.3-68
• /
• 2002

This paper presents a neural network approach to control exhaust gas recirculation(EGR) in a Liquefied Petroleum Gas(LPG) engine. In order to meet Increasingly stringent automotive exhaust emission regulations, alternative fuels such as LPG engines have been developed in many countries. HC&CO emissions of LPG engines can be easily reduced through air-fuel ratio control, but the control effect on NOx reduction is not good enough. Consequently EGR system is introduced to achieve a significant reduction in NOx emissions. Conventional EGR control uses the mapping method. The calibration time is long and the work is complex when adopting this mapping method. However neural networks are suitable f...

• 설비공학논문집
• /
• 제18권10호
• /
• pp.819-825
• /
• 2006

In a SOFC/GT (solid oxide fuel cell/gas turbine) hybrid power generation system, the recuperator is an indispensible component to enhance system performance. Since the expansion ratio to the recuperator core is very large, generally, the effective header design to distribute the flow uniformly before entering the core is crucial to guarantee the required performance. In the present study, we focus on the design of a diffuser type recuperator header with a 90 degree turn inlet port. To reduce the flow separation and recirculation flows, multiple horizontal vanes are used. The number of horizontal vanes is varied from 0 to 24. The air flow velocity is measured at 40 points just behind the core outlet by using a hot wire anemometer. Then, the flow non-uniformity is evaluated from the measured flow velocity. The experimental results showed that inlet air velocity did not effect on relative flow non-uniformity. According to increasing the number of horizontal vanes, flow non-uniformity reduced about $40{\sim}50%$ than without using horizontal vanes.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1997년도 한국자동제어학술회의논문집; 한국전력공사 서울연수원; 17-18 Oct. 1997
• /
• pp.484-487
• /
• 1997

In this paper a simulation program for the powertrain control of a gasoline engine with automatic transmission is presented, The object-oriented programming approach has been pursued, and MATLAB/ SIMULINK was adopted for its environment. The purpose of the paper is to demonstrate the programmability of a control system in the object-oriented fashion so that the transferability of the objects is guaranteed. The program developed in the paper was applied to a gasoline engine and the mathematical models used in the paper were just adopted from the literature. It is shown that the simulation results and real experimental results coincide well. Therefore, it is expected that the program or objects made in the paper are useful for the automotive engineers when they design a new engine/transmission system or modify a part of existing system.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.287-288
• /
• 2007

This paper is for a Real-time Active Control System to operate a boiler. By sensing of flame we wanted to get status of a furnace as many as possible, like load, efficiency, and/or amount of pollutant. These data can be used to make optimal running point by controlling the ratio of air and fuel. So the last object is to make a closed actual control loop from optical head to valve controllers. The first job was to design and to develop a optical data acquisition system. including optical sensor module. And we gathered flame data in variable situations for taking the trend of flame against burning environment. Currently we are developing a general system model, designing some control strategy and testing this active control system.

• 제어로봇시스템학회논문지
• /
• 제7권11호
• /
• pp.912-917
• /
• 2001

In this study, we define the measuring method of crank angle precisely using an event and perform a study on the hardware structure and software algorithms which is applicable for the commercial engine. Also we developed a Computer-ECU(Personal computer based electronic control unit) using a computer and a microprocessor, for performing the ignition at a desire position(angle) and for controlling a duty ratio a pulse for ISC(Idle speed control). We applied these algorithms to the modeling which is induced a concept of event and got a better result than a conventional ECU in the state of transient as a result of performing air fuel ratio control in a commercial engine. This technique can be used for the back to improve ECU performance. It the present type of Hybrid I. C voltage regulator is altered to the new type of regulator, we will be surely able to reduce the production cost as well as simplify the design of alternator\`s rear bracket and rectifier part because of the removal of trio diode. Experiment is taken by MS-R004.

• Journal of Biosystems Engineering
• /
• 제8권2호
• /
• pp.49-61
• /
• 1983

U shape multitube heat exchanger was equipped in the flue to recover the exhaust heat from the boiler system. The fluids of the exhaust heat recovery equipment were the flue gas as the hot fluid, and the water as the cold fluid. The flow geometry of the fluids was cross flow - two pass, the hot fluid being mixed and the cold fluid unmixed. The results of the theoretical and the experimental analysis and the economic evaluation are summarized as follows. 1) The heat exchanger effectiveness and the temperature efficiency of the hot fluid were about 35% when the fuel consumption rate was 140 - 150 L/15min. The temperature efficiency for the cold fluid ranged from 3.0% to 4.5%. The insulation efficiency ranged from 85% to 98%, which was better than the KS air preheater insulation efficiency of 90%. 2) The relationship between the fuel consumption rate, F, and the outlet temperature, $T_{h2}$, of the flue gas from the heat exchanger was $T_{h2}$ = 0.927F + 110. In order to prevent the low temperature corrosion from the coagulation of $SO_3$, it is necessary to maintain the fuel consumption rate above 82 L/15min. 3) The ratio of the exhaust heat from the boiler system to the total energy consumption was about 14.5%. With the installation of the exhaust heat recovery equipment, the energy recovery ratio to the exhaust heat was about 25%. Accordingly, about 3.6% of the total fuel consumption was estimated to be saved. 4) Economic analysis indicated that the installation of the exhaust heat recovery equipment was feasible to save the energy, because the capital reocvery period was only 10 months when the fuel consumption rate was 80 L/15min. 4 months when it was 160 L/15min. 5) Based on the theoretical and the experimental analysis, it was estimated to save the energy of about 18 million Won per year, if four heat exchangers are installed in a factory. 6) A further study is recommended to identify the relationship among the flow rate of the exhaust gas, the size of the heat exchanger and the capacity of the air preheater. For a maximum heat recovery from the exhaust gas an automatic control system is required to control the flow rate of the cold fluid depending on the boiler load.