• Journal of the Korea Concrete Institute
• /
• v.16 no.6 s.84
• /
• pp.805-811
• /
• 2004

In this paper, effects of mixture proportion and material condition on both fundamental properties, drying and autogenous shrinkage of high performance concrete are discussed. According to the results, for the effect of mixture proportion on the fundamental properties, decrease in W/B and unit water content results in reduction of fluidity, while air content has no variation. Compressive strength exhibits an decreasing tendency with an increase in W/B and unit water content do not remarkable affect the compressive strength. For the effect of materials on the fluidity, the fluidity of low heat portland cement(LPC) is smaller than that of ordinary portland cement(OPC). The use of Polycarbonic acid based superplasticizer(PS) has more favorable effect on enhancing fluidity than Naphtalene based superplasticlzer(NS) and Melamine based superplasticizer(MS). Air content of concrete using LPC is larger than that using OPC. The effects of superplasticizer type on the air content is larger in order of MS, PS and NS. The use of LPC exhibited lower strength development at early age than OPC, whereas after 91days, similar level of compressive strength is achieved regardless of cement type. Compressive strength of concrete is not affected by SP type. For the effect of mixture proportion and materials on drying and autogenous shrinkage, an increase in W/B results in reduction of drying shrinkage and an decrease in water content leads to reduce drying shrinkage. Autogenous shrinkage is not observed until 49 days with the concrete mixture with $35\%$ of W/B and $145 kg/m^3$ of water content. This is due to the combination effects of expansion admixture and shrinkage reducing admixture, which causes an offset of autogenous shrinkage. The use of LPC results in a reduction in autogenous shrinkage compared with OPC. SP type has little influence on the autogenous shrinkage. It is found from the results that mixture proportioning of high performance concrete incorporating fly ash, silica fume, expansion admixture and shrinkage reducing admixture is need to focus on the increase in W/B and the reduction in water content and the use of LPC and MS is also required to use to secure the stability against shrinkage properties.

• Journal of Korean Society of Forest Science
• /
• v.107 no.1
• /
• pp.1-15
• /
• 2018

In order to determine the effects of thinning on mushroom fruiting, microclimate and air temperature in Quercus mongolica forests, this study investigated changes in crown density, soil temperature, air temperature and throughfall in the natural Q. mongolica forest which was thinned by approximately 45% four years ago. The results showed that crown density was smaller than control by 6% from April to October, The soil temperature and air temperature in the thinned stands were significantly higher than those of the control by $1{\sim}2^{\circ}C$ until August and differences in air and soil temperature. The average daily temperature difference was higher than control by $0.2{\sim}0.7^{\circ}C$ until October. Throughfall from July to September in the thinned was approximately 135 mm higher than in the control. The maximum difference in throughfall per unit time was 3.5 mm/h. Soil moisture in the thinned site increased by approximately 5% compared with the control and reduced to the normal moisture after 4 days in both sites. 55 mushroom species were found in the thinned area between July and September. The thinned site contained 10 mycorrhizal mushrooms more than the control and 1 saprophytic mushroom species more than the control. Shannon-Wiener Index was 3.2, approximately 0.5 higher than the control. Tylopilus neofelleus, etc., occurred in the thinned site more quickly, but Aaricus subrutilescens, Clitocybe sp, occurred later. In the thinned site, the dominance of Tylopilus neofellelus and Armillaria sp. increased approximately 6% and 30% and yield about 1.5 times and 20 times, respectively. In conclusion, thinning in the Q. mongolica forest increased the soil and air temperature, soil moisture, throughfall and the diversity of mushroom species, and advanced the period of occurrence, and increased dominance and yield of some mycorrhizal mushrooms and Amillaria sp.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.34 no.10
• /
• pp.1599-1605
• /
• 2005

The object of this study is to develop the method for differentiating fresh meat from frozen meat by using the measurement of the mitochondrial malate dehydrogenase in the Korean native cattle. The principle of this experiment is based on the fact that the enzyme proteins associated with mitochondrial membrane could be released by freezing. The methods of differentiating fresh meat from thawed, frozen meat were studied by measurements of mitochondrial malate dehydrogenase activity of meat press juice. Fresh and frozen beef were stored at 4, -4, -18 and -77$^{\circ}C$ for 15-day storage period. A meat press machine using air pressure was manufactured especially for these experiments, and sufficient amount of drip (about 0.15 mL/g) from 1.5 g of beef sample was efficiently obtained under a pressure of 8 kg/$cm^{2}$ generated by the meat pressing machine. The mitochondrial malate dehydrogenase activities of frozen meat drip i년ices stored at -18 and -77$^{\circ}C$ were significantly higher than those of fresh and frozen meat samples at -4$^{\circ}C$ (p < 0.05) during 10-min reaction period. However, the enzyme activities of the frozen meat drip juices (-18 and -77$^{\circ}C$) disappeared after 5 minutes of the reaction, which was not observed from the fresh and -4$^{\circ}C$ frozen meats. The enzyme activity maintained until 12 minutes for the fresh and -4$^{\circ}C$ frozen meats. From these results, the mitochondrial malate dehydrogenase could be considered as an indicator to differentiate fresh beef from frozen one.

• Journal of the Korea Concrete Institute
• /
• v.21 no.3
• /
• pp.283-290
• /
• 2009

Differently from fly ash, the bottom ash produced from thermoelectric power plant has been treated as an industrial waste matter, and almost reclaimed a tract from the sea. If this waste material is applicable to foam concrete as an aggregate owing to its light-weight, however, it may be worthy of environmental preservation by recycling of waste material as well as reducing self-weight of high-rising structure and horizontal forces and deformations of retaining wall subject to soil pressure. This study has an objective of evaluating the effects of application of bottom ash on the mechanical properties of foam concrete. Thus, the ratio of bottom ash to cement was selected as a variable for experiment and the effect was measured in terms of unit weight of concrete, air content, water-cement ratio and compressive strength. It can be observed from experiments that the application ratios have different effects on the material parameters considered in this experiment, thus major relationships between application ratio and each material parameter were finally introduced. The result of this study can be applied to decide a mix design proportion of foam concrete while bottom ash is used as an aggregate of the concrete.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.11
• /
• pp.870-877
• /
• 2020

A suction bucket foundation, especially useful at depths of more than 20m, is a method of construction. The method first places an empty upturned bucket at the target site. Then, the bucket is installed by sucking water or air into it to create negative pressure. For stability, it is crucial to secure the verticality of the bucket. However, inclination by the bucket may occur due to sea-bottom conditions. In general, a repeated intrusion-pulling method is used for securing verticality. However, it takes a long time to complete the job. In this paper, we propose a real-time suction bucket verticality monitoring system. Specifically, the system consists of a sensor unit that collects raw verticality data, a controller that processes the data and wirelessly transmits the information, and a display unit that shows verticality information of a circular steel pipe. The system is implemented using an inclination sensor and an embedded controller. Experimental results show that the proposed system can efficiently measure roll/pitch information with a 0.028% margin of error. Furthermore, we show that the system properly operates in a suction bucket-based model experiment.

• The Korean Journal of Physiology
• /
• v.9 no.2
• /
• pp.7-15
• /
• 1975

The maximum breathing capacity (MBC) and the maximum mid-expiratory flow rate (MMF) are widely used in evaluation of the ventilatory function, among various parameters of pulmonary function. The MBC volume is the amount of gas which can be exchanged per unit time during maximal voluntary hyperventilation. Performance of this test, unlike that of single breath maneuvers, is affected by the integrity of the respiratory bellows as a whole including such factors are respiratory muscle blood supply, fatigue, and progressive trapping of air. Because of this, the MBC and its relation to ventilatory requirement correlates more closely with subjective dyspnea than does any other test. The MMF is the average flow rate during expiration of the middle 50% of the vital capacity. The MMF is a measurement of a fast vital capacity related to the time required for the maneuver and the MMF relates much better to other dynamic tests of ventilatory function and to dyspnea than total vital capacity, because the MMF reflects the effective volume, or gas per unit of time. Therefore, it is important to have a prediction formula with one can compute the normal value for the subject and the compare with the measured value. However, the formulas for prediction of both MBC and MMF of the Korean children and adolescents are not yet available in the present. Hence, present investigation was attempt to derive the formulas for prediction of both MBC and MMF of the Korean children and adolescents. MBC and MMF were measured in 1,037 healthy Korean children and adolescents (1,035 male and 1,002 female) whose ages ranged from 8 to 18 years. A spirometer (9L, Collins) was used for the measurement of MBC and MMF. Both MBC and MMF were measured 3times in a standing position and the highest values were used. For measurement, the $CO_2$ absorber and sadd valve were removed from the spirometer in order to reduce the resistance in the breathing circuit and the subject was asked to breathe as fast and deeply as possible for 12 seconds in MBC and to exhale completely as fast as possible after maximum inspiration for MMF. During the measurement, investigator stood by the subject to give a constant encouragement. All the measured values were subsequently converted to values at BTPS. The formulas for MBC and MMF were derived by a manner similar to those for Baldwin et al (1949) and Im (1965) as function of age and BSA or age and height. The prediction formulas for MBC (L/min, BTPS) and MMF (L/min, BTPS) of the Korean children and adolescents as derived in this investigation are as follows: For male, MBC=[41.70+{$2.69{\times}Age(years)$}]${\times}BSA$ $(m^{2})$ MBC=[0.083+{$0.045{\times}Age(years)$}]${\times}Ht$ (cm) For female, MBC=[45.53+{$1.55{\times}Age(years)$}]${\times}BSA$ $(m^2)$ MBC=[0.189+{$0.029{\times}Age(years)$}]${\times}Ht$ (cm) For male, MMF= [0.544+{$0.066{\times}Age(years)$}]${\times}Ht$ (cm) For female, MMF=[0.416+{$0.064{\times}Age(years)$}]${\times}Ht$ (cm)

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.45 no.2
• /
• pp.85-95
• /
• 2009

The fishing lamp is a fishing gear that gathers fish at night. But the cost of oil, which is used to light fishing lamp, has been risen significantly up to 30-40% of total fishing costs. Therefore it is very urgent to develop an energy economical fishing lamp in order to solve the business difficulties of fisheries. Under this background, this research aims at developing a fishing lamp for squid jigging and hairtail angling fishery using the LED, which has excellent energy efficiency and durability. The LED fishing lamp developed can be controlled to fix a fit direction of fish shoal deep because a fishing lamp can be adjustable up and down directions. One unit of fishing lamp has about an 80Watt capacity and the frame of fishing lamp is made of aluminium to emit generated heat of LED to outside. The LED lamp developed was highly durable, only 5.7% of emitting efficiency decreased for 18 months. The illuminance of a unit LED lamp was 2,070lux at 1m and 21lux at 10 m distance, and the intensity of LED lamp system emitted 2,580lux and 400lux at the respective distances. After development of this fishing lamp, 100 units are installed on operating fishing vessels. Experimental results show that energy consumption of squid jigging and hairtail angling was reduced by 40% and 87%, respectively. In conclusion, our methods showed elevated fishing power, compared with traditional fishing method: 37.7% for squid jigging and 24.5% for hairtail angling.

• Proceedings of the Korea Contents Association Conference
• /
• 2009.05a
• /
• pp.120-126
• /
• 2009

As the information age grows rapidly, the amount of digital texts has been increasing as well. It has brought an increasing of visualization case in order to figure out lots of digital texts. Existing visualized design of digital text is merely concentrating on figuration of subject word through adoption of stemming algorithm and word frequency extraction, prominence of meaning of text, and connection in between sentences. So it is a fact that expression of rhythm that can visualize sentimental feeing of digital text was insufficient. Syllable is a phoneme unit that can express rhythm more efficiently. In sentences, syllable is a most basic pronunciation unit in pronouncing word, phase and sentence. On this basis, accent, intonation, length of rhythm factor and others are based on syllable. Sonority, which is most closely associated with definitions of syllable, is expressed through air flow of igniting lung and acoustic energy that is specified kinetic energy into sonority. Seen from this perspective, this study examines phonologic definition and characteristics based on syllable, which is properties of digital text, and research the way to visualize rhythm through diagram. After converting digital text into phonetic symbol by the experiment, rhythm information are visualized into images using degree of resonance, which was started from rhythm in all languages, and using syllable establishment of digital text. By visualizing syllable information, it provides syllable information of digital text and express sentiment of digital text through diagram to assist user's understanding by systematic formula. Therefore, this study is aimed at planning for easy understanding of text's rhythm and realizing visualization of digital text.

• Applied Chemistry for Engineering
• /
• v.19 no.6
• /
• pp.652-660
• /
• 2008

For the recycling of rapid-chilled steel slag, the mechanical strengths and physical properties of EVA-polymer modified mortars with the various replacement ratios of rapid-chilled steel slag were investigated. Twenty five specimens of polymer modified mortars were prepared with the five different amounts of EVA-polymer modifier (0, 5, 10, 15, 20 wt%) and rapid-chilled steel slag (0, 25, 50, 75, 100 wt%). For the investigation of the characteristics of polymer modified mortars, the measurements such as water-cement ratio, unit volume weight, air content for fresh mortar and compressive strength, flexural strength, water absorption, hot water resistance, porosity and SEM investigation for curing specimens were conducted. As a results, with an increase in the replacement ratio of rapid-chilled steel slag, water-cement ratios decreased but unit volume weight increased remarkably. With increasing EVA-polymer modifier and the replacement ratio of rapid-chilled steel slag, percent of water absorption decreased but compressive and flexural strengths increased remarkably. By the hot water resistance test, mechanical strengths decreased but total pore volume and porosity increased remarkably. In the SEM observation, the components of specimen were shown to stick to each other in the form of co-matrix phase before hot water resistance test, but polymer modifier of co-matrix phase was decomposed or deteriorated after hot water resistance test.

• Journal of Korean Elementary Science Education
• /
• v.19 no.1
• /
• pp.131-143
• /
• 2000

The unit of a buoyant force included in the 7th national science curriculum for 6th grade students. On the contrary, it seldom that students' conception about buoyant phenomena is studied, even though there has been many studies of students' conceptions of basic science contents. The purpose of this study was to survey the elementary school students' conceptions of a buoyant force, to analyze their cognitive levels, and to explore the relationships between them. Sixth grade students (total numbers is 192) were selected .from 5 .lasses in two elementary schools in a local city of Kyungsangdo. They were asked to respond two kinds of test, which are the Logical Thinking Ability (GALT) to investigate students' cognitive levels and the Buoyant Force Questionnaire (BFQ). We developed BFQ test, based on the 7th national science curriculum for 6th grade and the previous researches of a buoyant force. We, qualitatively, analysed students' frequency of responses about a buoyant force and their types of explanation, and, quantitatively, analysed the relationships between cognitive levels and conceptions of a buoyant force with SPSS/ PC 7.0 programmes. The results of cognitive level showed that half of 6th grade students were in the concrete operational stage, 43.2% in the transitional stage, 6.8% in the formal stage. However, their sub-logical thinking abilities in a combinational, conservational, controlling variables, proportional, probability and correlational logic were very fluctuated from 91% to 8%. The results that only 4.8% of elementary students had correct conceptions of a buoyant force suggest that 6th grade students had great difficulties in understanding of that concept. Their difficulties would originated from the frequent common-sense explanations of a buoyant phenomena in terms of the weight or the unique properties or the contact area of an object or with/without air. Furthermore students' explanations, frequently, changed with context of problems of a buoyant force. Scheffe test of quantitative results that elementary students in the concrete level had 50.6% of concept formation in a buoyant force, the transitional level 54.5%, and in the formal operational level 62.8% showed significant differences of conceptions of a buoyant force with cognitive levels. Therefore the concrete operational elementary students had more difficulties of understanding of a buoyant force than the transitional and formal level, which is required to higher cognitive levels. This conclusion have implications that the unit of a buoyant force have to be presented with concrete activities for majority of students who are in concrete and transitional levels.