• 대한치과기공학회지
• /
• 제38권3호
• /
• pp.157-163
• /
• 2016

Purpose: It is to compare and evaluate the change of the wear rate and phase variation of the Zirconia before and after the sintering after the grinding by a high speed equipment manufactured for the Zirconia. Methods: The specimen of the sintered Zirconia was manufactured as size of $15mm{\times}15mm{\times}2mm$. The grinding has been applied to each of all pieces of each test groups for a minute fit for each condition at same speed of 50,000 rpm by a diamond bur at high speed handpiece with injection of the air and water. For the observation of the surface before and after the sintering of the each test piece, the cross section of it was observed as 100 magnification by a scanning electron microscope after it was coated by PT, and the diffraction analysis was performed by XDR to compare the crystal phase of the Zirconia. The average surface roughness value of all specimens were evaluated. The wear test was performed at room temperature by applying a load of 1kg for 120,000 cycles for the chewing period 6 months. Wear was analyzed for the enamel cusps by measurement of the vertical substance loss with a laser scanner. Conclusion: The phase variation from the tetragonal phase to the monoclinic phase was confirmed in the test group of the pre-sintered Zirconia after the grinding, and the value of the surface roughness and the wear rate was increased in experimental group.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 동계학술발표대회 논문집
• /
• pp.357-362
• /
• 2008

This study have goal with reverse engineering for petrochemistry of high pressure ball valve for localization. Ball valve for development accomplished with flow analysis based on provision of ANSI B16.34, ANSI B16.10, ANSI B16.25 In order to localize the petrochemistry high pressure control valve. Numerical simulation using CFD(Computational Fluid Dynamic) in order to predict a mass flow rate and a flow coefficient form flow dynamic point of view. The working fluid assumed the water($H_2O$). The valve inlet and outlet setup a pressure boundary condition. The outlet pressure was fixed by atmospheric pressure and calculated inlet velocity 5m/s. CFD solver used STAR-CCM+ which is commercial code. The result shows change of mass flow rate according to opening and closing angle of valve. Flow decrease observed open valve that equal percentage flow paten which is general inclination of ball valve. The structural analysis used ANSYS which is a commercial code. Stress analysis result of internal pressure in valve showed lower than yield strength. This is expect to need more detail design and verification for stem and seat structure.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2007년도 동계학술발표대회 논문집
• /
• pp.510-515
• /
• 2007

A Study on Typical Rates of Water-use for School Facilities has been carried out in this work. Water supply system is given much weight in school facilities. Therefore, it set up a basis efficiency using of water sources to calculate typical rates of water use. The results are summarized as follows ; 1) On the whole, typical rates of water-use was founded out 15 L / stu. d in pirmary school, 10 L / stu. d in middle school and 30L / stu. d in high school smaller than the existing it. It was rate of water-use change as season and Max. Rates of water-use was July. 2) I deem that school hours are 5 hour's in primary school, 7 hour's in middle school and 8 hour's in high school. It the concept of 1 hour that is lesson time 40 minutes and resting time 10 minutes in primary school, lesson time 45 minutes and resting time 10 minutes in middle school and lesson time 50 minutes and resting time 10 minutes in high school. 3) It is desired that we calculate the volume of pump and water tank throughout this concept and the size of water tank should be 1.5 times with taking pick load into consideration by this study on typical rate of water-use. 4) The amount of using water increases in gradually and I consider the life cycle of facilities is more than 10 years. As a result, I can forecast that the size will be insufficiency but I deem that if we devise a plan about parallel pumping on water tank space, we can cope with it. Also, it is expected that we can cut back the transport energy by controlling pump volume.

• 한국화재소방학회논문지
• /
• 제28권5호
• /
• pp.37-43
• /
• 2014

재실자가 부속실로의 피난 시 부속실 송풍기가 작동하기 전단계에서는 실내화재로 인한 풍속이 발생하여 부속실 개방과 더불어 연소생성물이 부속실을 오염시켜 피난장애의 결과를 가져올 수 있다. 이로인한 화재크기 및 실내 개구부 크기가 화재풍속에 미치는 영향을 확인하기 수치해석 연구를 수행하였다. 수치해석에서는 화재크기 및 실내 개구부 크기를 달리하였고, 실제의 공동주택 형상과 치수를 반영하였다. 수치해석 결과, 화재크기별 실내의 개구부 크기에 따라서 중성대 높이가 변화하여 부속실로 흐르는 화재풍속 특성이 다르게 나타남을 확인할 후 있었다. 또한, 실내 중성대가 높은 곳에 형성된 경우에는 방화문 상 하부에서 화재풍속의 차이가 나타남을 확인할 수 있었다.

• 대한통합의학회지
• /
• 제8권4호
• /
• pp.155-161
• /
• 2020

Purpose : This study was conducted to investigate the effect of positive active pressure technique and active breathing technique on lung function in healthy adults. Methods : In this study, the passive lung expansion technique and active respiration enhancement technique using an air mask bag unit were conducted in 30 normal adults to observe changes in pulmonary function with forced vital capacity (FVC), Forced expiratory volume at one second (FEV1). In order to observe the change in the level of respiratory function, we would like to investigate the peak expiratory flow (PEF) and the forced expiratory flow (FEF 25-75 %). Results : As a result of this study, there was no significant difference in comparison between the passive lung expansion technique and the active breathing enhancement technique (p>.05). The passive lung expansion technique effectively increased the effortful expiratory volume and the median expiratory flow rate of 1 second (p<.05). And the passive lung expansion technique effectively increased the effortless lung capacity and the maximum expiration flow rate (p<.05). Conclusion : The passive lung expansion technique effectively increases the range of motion of the lungs and chest cages, intrathoracic pressure, and elasticity of the lungs, and the active breathing technique increases the muscle functions such as the diaphragm and the biceps muscles. It is expected that it will be able to selectively improve the respiratory function of patients with respiratory diseases or functional limitations as it is found to be effective.

• 플랜트 저널
• /
• 제18권3호
• /
• pp.52-61
• /
• 2022

본 연구는 실제 운영중인 영동에코발전본부 1호기 125 MW 우드펠릿 발전소를 대상으로 탈질설비 운전조건이 NOx 발생량에 미치는 영향을 시험하였다. SNCR 요소 유량 증가에 따라 NOx 농도는 점차 감소하였으나 SCR 후단 암모니아 슬립은 상승하였다. 시험대상 보일러는 고온의 내부온도로 인해 SNCR 운영에 불리한 구조이며 노즐의 최적위치 검토가 필요할 것이다. SCR 희석공기 온도변화는 NOx 발생량에 영향을 미치지 않았다. SCR 암모니아 유량 증가는 SCR 후단 NOx 농도를 감소시켰고 NOx 제거효율도 증가시켰다. 다만 암모니아 슬립 자체 기준치를 초과하지 않는 암모니아 유량 111 kg/h가 최대 운전기준으로 추정된다. SCR 믹서 압력 상승은 NOx 농도를 감소시키고 제거효율도 최대로 측정되어 NOx 생성을 가장 효과적으로 억제하는 변수로 파악되었다.

• Journal of Animal Science and Technology
• /
• 제64권4호
• /
• pp.782-791
• /
• 2022

The purpose of this study is to evaluate the effects of multiple cooling systems and different drinking water temperatures (DWT) on the performance of sows and their hair cortisol levels during heat stress. In this study, the effect of four different cooling systems: air conditioner (AC), cooling pad (CP), snout cooling (SC), and mist spray (MS), and two DWT, namely low water temperature (LWT) and high water temperature (HWT) on 48 multiparous sows (Landrace × Yorkshire; 242.84 ± 2.89 kg) was tested. The experiment is based on the use of eight replicas during a 21-days test. Different behaviors were recorded under different cooling treatments in sows. As a result, behaviors such as drinking, standing, and position change were found to be lower in sows under the AC and CP treatments than in those under the SC and MS treatments. Lying behavior increased under the AC and CP systems as compared with that under the SC and MS, systems. The average daily feed intake (ADFI) in sows and weight at weaning in piglets was higher under the AC, CP, and LWT treatments than under the SC, MS and HWT treatments. Sows subjected to SC and MS treatment showed higher hair cortisol levels, rectal temperature, and respiratory rate during lactation than those under AC and CP treatments. Hair cortisol levels, rectal temperature, and respiratory rate were also higher under the HWT than under the LWT treatment. As per the results of this study, the LWT has no significant effect on any of the behavioral factors. Taken together, the use of AC and CP cooling treatment is highly recommended to improve the behavior and to reduce the stress levels in lactating sows.

• 한국패류학회지
• /
• 제23권1호
• /
• pp.1-8
• /
• 2007

본 연구는 피조개 양식 산업의 지속적인 생산을 위해 양식현장에 바로 응용할 수 있는 기초 연구로서 인공치패를 대상으로 치패의 크기별, 저질 종류 및 입자 크기, 그리고 수온, 염분 및 공기노출에 따른 잠입 능력을 조사 하였다. 피조개 치패의 크기에 따른 잠입 실험 결과 실험 개시 후 300분 경과 후 각장 $16.3\;{\pm}\;1.2\;mm$에서 97.7%로 가장 높게 나타났고, 각장 $12.8\;{\pm}\;0.8\;mm$에서 97.0%, 각장 $9.2\;{\pm}\;1\;mm$에서 96.7%, 각장 $5.9\;{\pm}\;0.7\;mm$에서 96.3%로 치패의 크기에는 상관없이 각장 약 6 mm 이상이면 잠입이 가능하였다. 저질종류에 따른 잠입 실험 결과 실험 개시 300분 경과 후에는 잠입률이 모래(75%) + 뻘 (25%) 에서 98.3%로 가장 높게 나타났으며, 뻘(100%) 에서 98.0%, 모래 (50%) + 뻘 (50%) 에서 97.3%, 모래 (25%) + 뻘 (75%) 에서 97.3%, 모래 (100%) 에서 86.3%순으로 나타났다. 입자크기에 따른 잠입 실험 결과는 실험 개시 300분 경과 후 잠입률이 1 mm 모래에서 85.0%로 가장 높았고, $12\;{\mu}m$ 뻘에서 83.0%, 2 mm 모래에서 75.7%, 3 mm 모래에서 75.0%, 4 mm 모래에서 72.5%순으로 입자 크기는 1 mm 및 $12\;{\mu}m$ 뻘이 잠입에 적정한 것으로 판단된다. 공기노출 시간에 따른 잠입 실험 결과는 실험 개시 300분 경과 후 1시간 노출구가 93.3%로 가장 높았고, 3시간 노출구 86.7%, 6시간 노출구 86.7%, 9시간 노출구 80.0%, 12시간 노출구 36.7%, 18시간 노출구 33.3% 및 24시간 노출구 30.0%로 노출시간이 길수록 잠입률이 낮았다. 수온에 따른 잠입 실험 결과는 실험 개시 300분 경과 후 $30^{\circ}C$에서 96.7%로 가장 높게 나타났고, $25^{\circ}C$에서 90.0%, $20^{\circ}C$에서 90.0%, $15^{\circ}C$에서 73.3%, $10^{\circ}C$에서 63.3% 및 $5^{\circ}C$에서 56.7%로 수온이 $30^{\circ}C$ 이내에서는 높을수록 높은 경향을 보였다. 염분에 따른 잠입 실험 결과는 실험 개시 300분 경과 후 염분 30 psu에서 93.3%로 가장 높았고, 35 psu에서 90.0%, 25 psu에서 83.3%, 20 psu에서 60.0%, 15 psu 이하에서는 거의 잠입이 이루어 지지 않았다. 따라서, 적정 살포를 위한 잠입률은 치패의 크기와 상관없이 저질종류는 모래 (75%) + 뻘 (25%), 입자크기는 1 mm 모래에서 높게 나타났다. 공기 중 노출시간은 짧을수록, 수온은 $30^{\circ}C$ 이내에서 높을수록, 염분은 20-35 psu 이내에서 높을수록 잠입률이 높은 경향을 나타내었다.

• 한국환경보건학회지
• /
• 제46권6호
• /
• pp.735-749
• /
• 2020

Objectives: The aim of this study was to investigate airborne pollen counts, inhalant allergen sensitization rate, and allergic disease prevalence among elementary school children in Ulsan, South Korea during 2012-2018. Methods: Burkard samplers for pollen were installed on rooftops in suburban and urban areas in Ulsan. A 24-hour sampling of airborne allergens was conducted six days/week from January 1, 2013 to November 31, 2018. Skin prick tests were done with a total of 4,246 primary school students residing in urban and suburban areas in 2012, 2014, 2016, and 2018. This study examined sensitization to 20 major inhalant allergens. Results: The highest monthly counts of airborne pollen were observed in April and September each year. Among the pollen identified over the six years, pine showed the highest pollen counts (44.3%), followed by oak (22.3%), alder (6.3%) and Japanese hops (4.3%). Tree pollen predominated from March to June, and weed pollen predominated from August to October. Higher sensitization rates for inhalant allergens were observed in Dermatophagoides farinae (42.4%), Dermatophagoides pteronyssinus (43.6%), cat fur (12.1%), birch (9.9%), oak (9.6%), and alder (8.7%). The inhalant allergen sensitization rate was highest in the group with comorbidity (asthma and/or rhinitis and atopic dermatitis), and respiratory allergic disease (asthma and/or rhinitis) was higher than that of atopic dermatitis. Conclusion: Both the counts of tree pollen in the air and the sensitization rate for tree pollen were high in Ulsan. The temporal change in respiratory allergic diseases was similar to that for the sensitization rate of tree pollen, such as oak. In the future, it is considered that additional continuous research on various inhalant allergens and pollen should be conducted.

• 한국건설순환자원학회논문집
• /
• 제2권3호
• /
• pp.173-179
• /
• 2014

본 연구는 석탄을 사용하여 발전한 후 남은 폐기물인 석탄회를 콘크리트의 잔골재로 재활용하기 위한 실험적 연구이다. 석탄회는 크게 플라이 애시와 바텀 애시로 구분될 수 있다. 플라이 애시의 경우 콘크리트의 배합 시 시멘트를 대체하는 재료로 많이 활용되고 있는 반면 바텀 애시의 경우 대부분이 매립되고 있는 등 재활용률이 낮은 실정이다. 본 연구에서는 재활용률이 낮은 바텀 애시의 활용률을 증대시키고자 콘크리트의 잔골재로 일부 치환하였으며 활용성을 확인하였다. 콘크리트 배합 시 물시멘트 비를 고정한 상태에서 바텀 애시의 사용량을 증가 시키게 되면 작업성이 현저히 떨어지게 되므로 일정 수준이상 사용하기 위한 대책이 필요하다. 이러한 문제를 해결하기 위하여 폴리카르본산계 고성능 감수제를 사용하여 콘크리트를 배합하였고 콘크리트 비빔 직후 및 비빔 1시간 후 유동성 및 공기연행성을 비교하여 실제 레미콘이나 배치 플랜트에서 생산된 콘크리트가 현장에 타설되는 시간을 모사하였다. 연구 결과 바텀 애시를 잔골재의 30%정도 치환한 콘크리트 비빔 1시간 후 작업성과 공기연행성을 확보할 수 있었고, 압축강도는 다소 감소하였으나 바텀 애시를 콘크리트 잔골재로 사용할 수 있는 가능성을 확인할 수 있었다.