• Journal of the Korean Society of Visualization
• /
• v.15 no.2
• /
• pp.48-58
• /
• 2017

To analyze bubbles generated by an ABB (Air Bubble Barrier), we developed image processing procedure and statistical analysis method. Air was discharged from 5 mm nozzle as swarm form at the bottom of 1 m3 water tank. Flow rates of discharged air are ranged from 2 L/min to 20 L/min and these are corresponding to Reynolds number of 1766-17663. Rise velocity of bubble is extracted by using image process pretending intrusive method. Mean equivalent velocity was calculated using void fraction weighting factor. Bubble diameter is obtained and compared with correlations in the literature. Also, we present a correlation according to the result of this study. Mean velocity and mean diameter of bubbles increase with increasing gas Reynolds number. But these parameters show an asymptotic trend when they approach to high Reynolds number.

• The Korean Journal of Community Living Science
• /
• v.24 no.2
• /
• pp.187-194
• /
• 2013

The purpose of this study was to define the optimal boxthorn berries washing method for developing the boxthorn berries cleaner. We analyzed the rate of removal of residual pesticides according to washing methods; 1st - habitual washing method, 2nd - drum rotation washing method, 3th - drum rotation and air bubble washing method, 4th - drum rotation and nozzle spray washing method, 5th - drum rotation and air bubble and nozzle spray washing method. A rate of removal of residual pesticides of 88% was detected in the drum rotation and air bubble and nozzle spray washing method, and a rate of 82% was detected in the habitual washing method. The drum rotation and air bubble and nozzle spray washing method appeared to be the best good washing effect compared to the habitual washing method(about 6% compared to 82.0% higher). Clothianidin Triadimefon, Triforine ingredients, the drum rotation and air bubble and nozzle spray washing method efficiency was lower compared to the habitual washing method removal efficiency.

• Journal of the Korean Society of Visualization
• /
• v.15 no.2
• /
• pp.59-67
• /
• 2017

To verify floatability of ABB (Air bubble barrier), we compared bubble swarm behavior with and without the air-driven ejector. Experiment was conducted using the fabricated air-driven ejector with 5 mm nozzle on the bottom of 1 m3 water tank. Reynolds number of air in the nozzle was ranged 1766-13248. We analyzed data with statistical method using image processing, particle mage velocimetry (PIV) and proper orthogonal decomposition (POD) analysis. As a result of POD analysis, there was no significant eigenmode in bubbly flow generated from the ejector. It means that more complex turbulent flows were formed by the ejector, thereby (1) making bubbles finer, (2) promoting three-dimensional energy transfer between bubble and water, and (3) making evenly distributed velocity profile of water. It is concluded that the air-driven ejector could enhance the performance of ABB.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.05a
• /
• pp.763-768
• /
• 2001

The purpose of this study is to research a specific material characteristics of top down concrete at column joint and to reduce column joint opening. Based on the established top down study, the experiment to apply an real construction case is performed. When the concrete placed into joint of top down column, raised air bubble is left as opening. This study is examined the incomplete packing reason in the top down column and found to air deflation method. The result of study is below (1) As the method to minimize column opening caused from confined air, it is required that an air exhaust port installation in joint column. (2) From air exhaust port installation, most of air bubble in column part is exhausted. As the concrete placing height is going up, air bubble size is going smaller.

• Journal of the Society of Naval Architects of Korea
• /
• v.37 no.4
• /
• pp.48-55
• /
• 2000

A basic research of air bubble locus around the ship hull is performed to know the bubble's behavior which is generated around the hull surface. In this paper. bubble's behavior around the ship hull is calculated and experimented with the variation of bubble size and the location of bubble generation. For the use of the equation for bubble locus, Kawakita's equation which include the effect of bubble buoyancy is adopted. For the numerical simulation. a finite difference method based on the MAC method is used. Also experiments are performed about series 60 hull form at CWC. The results of calculation are compared with those of experiment.

• The Journal of the Acoustical Society of Korea
• /
• v.40 no.4
• /
• pp.320-329
• /
• 2021

In this paper, an empirical model of air bubble size to be applied to an air masker for reduction of underwater radiation noise is presented. The proposed model improves the divergence problem under the low-speed flow condition of the existing model derived using Rayleigh's jet instability model and simple continuity condition by introducing a jet flow velocity of air. The jet flow velocity of air is estimated using the bubble size where the liquid is quiescent. In a medium without flow, the size of the bubble is estimated by an empirical method where bubble formation regime is divided into a laminar-flow range, a transition range, and a turbulent-flow range based on the Reynolds number of the injected air. The proposed bubble size model is confirmed to be in good agreement with the Computational Fluid Dynamics (CFD) analysis result and the experimental results of the existing literature. Using the acoustic inversion method, the air bubble population is estimated from the insertion loss measured during the air injection experiment of the air- masker model in a large cavitation tunnel. The results of the experiments and the bubble size model are compared in the paper.

• Architectural research
• /
• v.26 no.1
• /
• pp.13-20
• /
• 2024

This study is a research investigation into the properties of bubbles that affect the characteristics of foamed concrete during its production. The study examined the properties of bubbles based on the manufacturing conditions. To investigate these properties, the selected experimental factors included bead size, the length/diameter ratio of the bubble-generating tube, and compressed air. The experimental design used a design of experiments, and the test results were analyzed using analysis of variance. The foaming agent used to generate bubbles was AES (Alcohol Ethoxy Sulfate), and the method employed for bubble manufacture was the pre-foaming method. In the test results, a significant factor affecting the foaming rate of bubbles was the bead size; the highest foaming rate was observed when using 2mm beads. Bead size also primarily influenced the volume change of the aqueous solution, while other factors did not affect the foaming rate and volume change. None of the factors affected the change in bubble size, but compressed air was considered the main factor affecting bubble size and its change. The foaming rate and volume change of the aqueous solution showed a high correlation with each other. Spherical bubbles in the early stage eventually transformed into angular bubbles. Moreover, over time, it was observed that the bubble size increased.

• The Journal of the Acoustical Society of Korea
• /
• v.42 no.3
• /
• pp.227-232
• /
• 2023

Underwater noise pollution has a significant impact on the marine environment. This study proposed a simple approach to estimate the acoustic radiation efficiency of structures with air bubble layers. The method considered the insertion loss caused by the air bubble layer through post-processing of numerical results, assuming that insertion loss is equivalent to attenuation as demonstrated by previous studies. The proposed approach was validated by comparing it with a fully coupled analysis for plate structure models. The commercial finite element program COMSOL Multiphysics was used for the acoustic-structure interaction analysis, and the acoustic characteristics of air bubble layer for the fully coupled analysis was simulated by on the Commander and Prosperetti theory. The trends indicated good agreement between the simple approach and the fully coupled analysis in terms of radiation efficiency. It is confirmed that the proposed method is providing insight into the principal mechanism of underwater noise reduction for the bubble layer on the wedge-shaped structure.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.835-838
• /
• 2002

An experiment has been performed using a facility, which simulates the safety depressurization system (SDS) and in-containment refueling water storage tank (IRWST) of APR1400, an advanced PWR being developed in Korea, to investigate the dynamic load resulting from the blowdown of steam from a steam generator through a sparser. The influence of the key parameters, such as air mass, steam pressure, submergence, valve opening time, and pool temperature, on frequency and peak toads was investigated. The blowdown phenomenon was analyzed to find out the real cause of the initiation of bubble oscillation and discrepancy in frequencies between the experiment and calculation by conventional equation for bubble oscillation. The cause of significant damping was discussed and is presumed to be the highly tortuous flow path around bubble. The Rayleigh-Plesset equation, which is modified by introducing method of image, reasonably reproduces the bubble oscillation in a confined tank. Right after the completion of air discharge the steam discharge immediately follows and it condenses abruptly to provide low-pressure pocket. It may contribute to the negative maximum being greater than positive maximum. The subsequently discharging steam does not play as at the driving force anymore.

• Journal of computational fluids engineering
• /
• v.13 no.4
• /
• pp.126-134
• /
• 2008

We developed a three dimensional Navier-Stokes code based on the level set method to simulate two phase flows with high density ratio. The Navier-Stokes equations with consideration of the surface tension effects are solved by using SIMPLE algorithm on a non-staggered grid. The present code is validated by simulating two test problems. First one is to simulate a rising bubble inside a cube. The thickness of the interface of the bubble is shown to affect the pressure distribution around the interface. As the thickness decreases, the pressure field around the interface becomes more oscillatory. As the bubble rises, a ring vortex is shown to form around the interface and the bubble eventually develops into an ellipsoidal shape. Merge of two bubbles inside a container is secondly tested to show the robustness of the present code for two phase flow simulation. Numerical results show stable and reliable behavior during the process of merging of two bubbles. The velocity and pressure fields around the interface of bubbles are shown oscillation free during the merging of two bubbles.